These new companies no longer charge crazy upfront fees, moving instead to what’s known as a “SaaS” monthly subscription model, often with a free trial period. Therefore, the risk of trying a new product is greatly reduced, as you are required to pay little or nothing upfront. Even Microsoft announced in 2015 that they would be moving their flagship product, Microsoft Office, to this pricing model.
If you have a broker that’s too successful you may be a low priority. If you choose a broker that’s inexperienced but attentive, you may end up paying for their novice mistakes. My advice is to not choose a broker but instead choose a team. Pick a junior/senior combo so that when you’re hunting for space you work more with the junior, and when it comes to negotiating the deal you have the experienced veteran leading the negotiation.”
Shop layout is all about making the best use of space. Place your machines so that you have adequate “safe space” that you need to work around them. The “buffer area” beyond that is the amount of room you need to run large stock though a given machine, keeping in mind that buffer areas can overlap between machines. If you want to get more organized, buy some 1/4-inch squared paper, make scale models of each machine including the safe space around each, and place them on your model shop layout. Remember that buffer areas need to be long enough to put an 8' sheet through a table saw, or a 6' plank through your planer, for instance. I raised my planer, so that I can use the area above my router table to pass long planks through the planer – all it takes is some modelling, and a little shuffling, and you will find the layout that works for you. Each space will have challenges; I had the area under the stairs that was wasted space, so I installed the dust collector there.
Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regulations, a larger lot, or more congenial neighbours.
Chris Marshall: You’re asking a question that would take many magazine articles or a whole chapter of a good shop-design book to answer adequately. If you haven’t already done so, you might also want to ask this question to the good folks that frequent our forum on woodworking.com. Every woodworker with a shop will have a slightly different answer, so here’s mine. I’ve never had a brick shop, but my last one was a metal pole barn (30 ft. x 40 ft.). I outfitted the interior with 2×6-framed walls and plenty of insulation. It stayed reasonably cool in the summer and warm in the winter, using a wall air conditioner and a 60,000 BTU furnace. Currently, I have a 24 ft. x 42 ft. garage space for my shop. It is framed conventionally with 2×6 walls and stick-built 2×10 rafters. I’ve only been in my new shop for about a year, but it is working just as well or better than my pole barn did, because the new shop has many large windows that let in lots more natural light. I’ve used 8-ft. fluorescent T8 light fixtures in both buildings with good success, and I ran both 110- and 220-volt outlets all around the room. The last shop had a plywood floor; the current one, a concrete slab. I thought I would notice a bigger difference between the two flooring types, in terms of how tired it makes my legs by the end of the day. But in all honesty, a good pair of supportive shoes seems to make the difference moot for me. Both types of buildings benefit from a dehumidifier during humid months (when I’m not running the A/C, that is) to keep the relative humidity low and my tools rust-free. If all things were equal, and money were no object, I would probably go with a conventionally framed wood building over the pole barn. It was easier to build that from scratch as opposed to retrofitting the pole barn framing with walls afterward. But, as I say, the next woodworker will probably offer you a completely different answer from mine. Good luck in your decision!
Many small businesses in New York and New Jersey were forced to close following Superstorm Sandy because they lacked the insurance that would have gotten them back on their feet. That part is well known. What’s less well known is that this lack of proper insurance, coupled with the lack proper legal incorporation, resulted in many entrepreneurs seeing their personal assets come under threat.
I used to keep screws in a cof- fee can, but when I reached in with my hand, the screw points pricked my fingers. The can was also a dust and dirt depot. I bought a clear water bottle with a pop-up lid and poured screws into the bottle with a funnel. The screws stay clean, and I can shake them out of the bottle one at a time. — Bruce Burley. Hardware Storage: DIY Tips and Hints
I think it would work pretty well for a music festival, I don’t see why not. I wouldn’t say it is robbery proof, but generally robbers are looking for quick and easy targets, like a purse sitting on the front seat, just smash and grab. If someone really wanted to rob what was under they platform, they surely could, but they’d need more tools and more time to do so. And they don’t even know if there is anything good under there… I’d like to think of it as a really good robbery deterrent.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.