Hand tools offer your best chance of finding a real bargain. Until the early 20th century, nearly all woodworking was done with hand tools, and their designs and uses have changed little. Most of the high-end planes on today’s market, for example, are just reproductions of the original designs. And because the originals were mass-produced, they are fairly easy to find at rummage sales and antiques stores. (For more information, refer to Matthew Teague’s article, “Buying Old Tools,” in FWW #180).
We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.
Solar Shower. For easy, inexpensive showering in wilderness locations, nothing beats a good solar shower. This is basically a bag of water that you leave out in the sun until it heats up, then hang it from a high place and shower using the attached nozzle. 5-gallon solar showers should get you about 5 minutes of good water flow. There are also pricier but more convenient pump-operated solar showers that you can buy.
There are certain areas that are the responsibility of the federal government, such as firearms, fish, and wildlife. For more on these federal requirements, enforced by bodies such as the Food and Drug Administration (FDA) and the Environmental Protection Agency (EPA), you can explore the information here on the Small Business Administration (SBA) website.

When you set out to start your small business, investing in the right technology and equipment should be considered in conjunction with your store design. They should seamlessly integrate with and improve the customer experience in your store. Everyone remembers their first trip to the Apple Store and the “wow” moment of having their sale rung up by the assistant in the middle of the store, rather than having to wait in a line. But fewer people probably notice the carefully positioned heater that creates a warm environment for them as they walk through the door. It’s all part of the same idea.


Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
In today’s competitive business landscape, the key card that small business owners hold up their sleeve is their ability to offer something distinctive, original, and personal. As small businesses grow, however, it can become increasingly difficult for the time-pressed, financially strapped entrepreneur to maintain direct oversight over every aspect of their store.
When Julie Owen bought Cocobolo Interiors in 2008, she set about adding more contemporary items to the Armonk, N.Y., shop. But with only 3,000 square feet, she struggled to figure out where to put her expanding line of furniture, lighting fixtures and accessories. Her solution: create sections within the shop and arrange the furniture the way customers might imagine it at home, using low bookcases and folding screens as dividers.
Some people lean towards starting a small business because they seek freedom, others to fulfill their passions. Some entrepreneurs, however, are driven by a desire to build a legacy, one that that they can hand down to generations to come. Whatever your reasons are for reaching for the stars and aiming for the moon, before you start, remember, there is a dark side.

When you set out to start your small business, investing in the right technology and equipment should be considered in conjunction with your store design. They should seamlessly integrate with and improve the customer experience in your store. Everyone remembers their first trip to the Apple Store and the “wow” moment of having their sale rung up by the assistant in the middle of the store, rather than having to wait in a line. But fewer people probably notice the carefully positioned heater that creates a warm environment for them as they walk through the door. It’s all part of the same idea.


While you have a decent starter shop, it's important to keep in mind the projects that your tools can handle.  You are going to want to focus on projects that don't require your stock to be ripped to a different dimensions than what you purchased it at.  You are currently only set up to do crosscuts with your miter saw.  So while you can turn an 8' 2x4 into two 4' 2x4s, your not going to be able to turn that same board into two 2x2s.    
Couldn’t disagree more. Still got the same setup a few years in. As mentioned the sag is minimal (not non-existent), I place a small removable 2×2 near the tailgate so I can hop up top. You’re not building a home up to code, you’re building a practical truck camping solution, and in my extensive experience it is more than fine. You can do thicker plywood, but realize that it will be much heavier and more cumbersome to move.
The good news is that when you’re starting your small business, you now have the tools to take a data-led approach to choosing the right store design. For example: Not sure what type of music gets your customers in the mood to spend? Simply choose a few different styles and display a different one each week. After the test is complete, analyze sales data to help you identify what could be impacting sales. The key to getting accurate results from this kind of test is to avoid switching up the other variables in your store that can impact sales, such as signage, or testing one type of music during a regular business week and another type during a holiday week. For more details on how to create controlled in-store experiments, you can check out Lean Retail 101

A great product line will also reflect a range of price points. For a business that is working hard to convey a sophisticated and elite vibe, it might be a useful strategy to set a high minimum price, but for the vast majority of small businesses, your pricing should be guided by one key thought: I want every single person who comes through my door to be able to find something that fits their budget. 

I get all the zen I need from Dunkin Donuts. :) Actually, I am reserving judgement concerning sound at this point and here’s why. I worked in a 1000 sq ft shop for the first 5 years of this show and never had any echo complaints. That was with 16 ft ceilings. The new shop was pretty unbearable to talk in when it was empty and became quite tolerable when filled with the initial equipment. With the addition of the floor pads and cabinetry, I am pretty confident the echo will be reduced fairly close to the previous shop’s level. If not, I’ll have to consider my options, because there’s no way I’m hanging drapes in my shop, lol.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
I will also typically secure those sorts of items under my locked platform if I am gone for a few days in the backcountry, because in reality I could probably care less if someone broke in and stole my box of food, versus someone who stole my clothes or expensive down jackets, which would be much more problematic (and costly) to replace on the road.
It might sound harsh, but when starting a small business your online presence is crucial. If you speak to some experienced local business owners, many will denounce the existence of online review sites like Yelp and Google Local. They’ll tell you about the added time and pressure they now face to maintain social media profiles for their businesses. A lot of local entrepreneurs will share their bad experiences with online daily deal websites like Groupon. But all that complaining doesn’t change one established fact that the internet isn’t going anywhere.
2) I haven’t spent very many nights in full on winter conditions (that 12 degree night in Boise comes to mind!), so I can’t comment too much. It was fine for that… Mostly it was hard transitioning from the warmth of the cab to the frigid air while you are shifting things around and getting ready for bed, but then once you were inside the canopy it was fine. Lots of frosty ice on the inside windows, but in my sleeping bag all was well. It stays a little warmer in the canopy. Maybe I’m a wuss, but I didn’t want to spend an extended period of time dirtbagging it in my truck while I was ice climbing (I spent the first two months in Ouray, CO, sharing a rental), I just thought it would be too challenging/miserable to dry and manage gear in a confined space with the shorter daylight hours. I’d be perfectly content doing future weekend trips with this setup though!
Above all, remember that all of these elements can form part of your negotiation. Unless you are pursuing a highly desired space in a hot rental market, there is usually a point of leverage available to you in every lease negotiation. When it comes to getting the best possible deal in these situations, you’ll want to seek quality professional advice, this will normally include a broker and real estate lawyer.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
As a retailer, it's possible to use furniture, displays, racks, and other tools to create a clear path for your customers through your store. This will vary greatly depending on the size and your general store layout. However, you know that most North American customers will naturally turn right — so, your next job is to make sure that as they do, they also continue walking throughout your store to gain the maximum exposure to your products. This not only increases the chances of them making a purchase, but a well-thought-out path can be a great way to strategically control the ebb and flow of foot traffic in your store. 
When starting your small business, the easiest way to go about choosing a business name is to approach the task the same way you approach building new relationships. Did we lose you for a second? Here’s what we mean. It takes just one-tenth of a second for us to judge someone based on a first impression. There are endless relationships that instantly blossom or never get off the ground based off of this one simple fact. Most of us, even if it is on a subconscious level, understand this. Which is why when we meet someone that we are trying to impress, we make an attempt to adjust our appearance, body language, even the way we talk, to ensure we are putting our best foot forward.
1) I haven’t lived with another person sleeping in the back (where you at ladies?!). I have spent a few weeks here and there on the road with others, I slept in the back, they had their own tent at camp. It does get crowded having two people with full alpine kits sharing the same storage space. You have to juggle space and work together to get to things. As for two people sleeping in the back, I think that would be pretty tight (doable, but challenging). In my research (links in this post at the bottom) I know there were a few couples living in a shared truck bed…

Now that you have written everything out, now take out a calendar that has 12-month blocks and map out each business goal in the corresponding month that it has to be completed by (or accomplished). So you have 12 squares (12 months) and you are literally placing these ideas into the month you want to accomplish them by. By the time you are done with this, you will have a sheet of paper with all your ideas written into the months on the calendar.
Without organization, living in a van can feel cluttered and chaotic, so you'll want to make the most of your storage space. This is a good time to make sure you've paired down your belongings to a reasonable amount and to make sure everything has a place. (As a former engineer who loves making things as efficient and optimized as possible, this was Ben's favorite step!) 

Back in the 1970s and treeplanting in Oregon, I and Tony Lessa lived for two weeks at a time in the back of my 1954 Chevy PU. The canopy was just a simple shell with the board across next to the cab. After the fourth or fifth trip out in the season the accumulated funk was too much. You can imagine two hard-working guys in very muddy and cold conditions coming in after work with dirty wet gear. Pretty desperate circumstances but before Reagan trashed the treeplanting industry our coop ( Hoedads & then Second Growth) was making good money so we endured the hardships. It works for the young. Now, at 76, I find sleeping two of us between the wheel wells in a Dodge G. Caravan (seats removed) much too crowded. I think I will tent and the wife can have the van.
Reactions are typically over-the-top excitement. Everywhere I go, there are people snapping pictures, taking videos, and giving me a “thumbs up.” Sometimes while on the highway, cars will go ahead of me about a mile or so and then pull over to get out and video me driving by them. Truck drivers are always getting on the CB radio asking about the truck.
You can see in this step how I notched each rafter to fit more securely to the walls.  I also used a metal hurricane strap to secure each rafter to the wall.  Even though this was not required by code, I felt my tools were far to valuable to be left to chance over such an inexpensive solution.  The walls are a simple board and batten system.  The 1x3 trim covers the joints of the 4x8 OSB.  They make much more high quality sheets goods to use as siding.  However, the cheapest I found was $35 a sheet and the OSB was about $5 a sheet.  I sealed the OSB and painted it with exterior paint.  If I run into problems in the future, I can just add a second layer of more durable material or simply have siding installed.  It has held up very well over the past couple years and I see no need to spend more money on it now.
Ultimate Small Shop is a turnkey solution for woodworkers to get started with their dream workshop. Every woodworker, hobbyist or professional, wants a nice workshop in their home. It may be the garage or a shed, the barn or a detached man cave, the basement or a room up somewhere with enough space. Woodworkers often fail to create their dream workshops due to dearth of space and funds. Ultimate Small Shop solves both these issues and empowers woodworkers to live their dreams.
There are benefits to either approach. Sharing a common wall with your house can require some careful soundproofing but can reduce heat loss and exterior fin­ishing costs like siding. A shop located in an addition is more likely to be allowed to have living space or storage space above it, and it may be easier to make use of the existing plumbing and electri­cal and heating systems of your home to service your shop space. Another advantage of an addition is not having to run to an outbuilding in minus-30-degree weather or a summer downpour.

Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.


First things first, the machinery is going to do the bulk of your work. Hand tool purists may argue differently but how many machines do you have in your home to make things easier? The same should be true for your workshop. Yes, there may be moments when you take a deep breath at the initial investment but if you’re looking at woodworking as a prolonged pastime then the tools will last you for years to come. Plus you’re not buying everything at once. Start small and build up your collection.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
Let’s say you’re a Brooklyn-based hipster and you want to follow your lifelong dream of opening your very own artisanal, organic lemonade stand. You’re planning on stationing your retro lemonade stand along a busy road in Williamsburg, Brooklyn. And maybe you want to hire a couple of college kids to collect the money and serve your customers, (probably while wearing some painfully cool 1970s punk band t-shirts). You’re only thinking about it semi-seriously. It might be something you’re going to do when you’re not focusing on your real career as an aspiring DJ.
Hey thanks for the great insight on a pickup camping setup! I just purchased a 2002 tundra with a 74″ bed. Picking it up in Denver in a week and driving it to Durango and then around the southwest. I mainly decided on a truck for a mobile place to keep my dog(that doesn’t have an interior he can rip to shreds), but I am thinking of building a setup similar to yours. You haven’t used yours with a canine companion have you? Any suggestions on keeping it dog-friendly, dog-comfortable and dog-proof? I will be keeping him in the back while at work and such and will be camping in the back with him and possibly another person.
Both of those broader lenses are still useful ways to look at app costs, but costs can additionally be broken down by app type and the features associated with them. Also, two years in technology is a very long time. So, we will start by looking at what's changed. We'll then move on to looking at app costs based on the different kinds of apps in the market.
Finally, think about the overall color and feel of your workshop. A fresh coat of bright white paint will help your lighting go farther, but you might also consider adding a splash of color for fun. An accent wall or an epoxy floor coating are good ways to upgrade your workshop from drab to fab without adding fussy decorations that will get in the way of business.
Boy you guys are spoiled, lol. There will always be at least some echo in the shop. I wouldn’t judge the acoustics based on this video though since the shop was still being put together at the time. No cabinets and no floor tiles, so the echo is to be expected. Have you seen the latest video? http://www.thewoodwhisperer.co.....rock-star/ The sound is dramatically improved over the Dream Shop video and all I did so far was add a few floor mats here and there. By the time the cabinets are in and I get some nice rubber floor tiles in place, the sound should be at least to the level of the old shop if not better. Right now though, my priority is on building a bed and I do consider the current sound to be “acceptable” for web videos. I’ll focus on tweaking things when I finally get some spare time. Considering adding some acoustic tiles to the ceiling.
×