Most businesses must obtain a variety of business licenses, permits, and registrations before opening their doors to the public. As a small business owner, it is your responsibility to ensure that you are abiding all the laws and regulations applicable in your state and to your particular industry. You also have to research and apply for all relevant permits and licenses that apply to your business type and location. Remember, it is impossible to plead ignorance as a defense. It’s up to you to educate yourself. When in doubt leave it to the professionals. CT Corporation offers custom license packages that simplify the process for business owners. Click here for an example of what that looks like.
I’m currently in the process of building my own small shop and I almost didn’t watch this video because I was afraid I might become too jealous. I wasn’t. It made me realize that a good shop is worth waiting for and that I don’t need to be discouraged when things aren’t moving as quickly as I hoped. Thank you for the inspiration and congratulations on your new shop, you deserve it.
I have a question, you mention what a problem it would be if the cinder blocks were to sink yet you have installed them with the least amount of footprint on the ground. Was there a reason for this? I would have installed them with the flat side on the ground, and I realize they would not hold as much load as the way you have them but considering the number you have used, the spacing, and the size of the shed, load should not be a problem. Just wondering.
My wife and I have just bought a block and will be building a new house – as part of this will be the building of the “shed” – which is really a workshop as I am a very keen Woodworker (I have most of the toys!!). My question is – Leaving money aside “Is a brick or metal shed better – especially in regards to moisture, inside temperature (heating and cooling), noise etc”? Any other suggestions would also be appreciated – eg lining the structure, power needs, lighting, etc. I appreciate your expert opinion. – Ivan Banks
It does sag a little bit, but not worryingly so. As I mentioned, it often rests on top of the large plastic boxes I place underneath, and I put in a small wooden brace at the entrance. You could definitely build it slightly smaller, or put in a more substantive center brace — like a sheet of plywood that fits into the groove of the bed liner and is the exact height you want.
Garage spaces are usually not insulated, and garage doors on most homes have very poor insulation. That means it’ll inevitably be super hot and stuffy in the summer, and freezing cold in the winter. To be comfortable in your workshop you’ll need to take the extra step to insulate your garage and set up some space heaters, and some portable floor or window AC units. Having to wear a heavy coat while you work will impede your DIY efforts and nobody likes working in a sauna.
While the recession brought with it a well-documented squeeze on small business lending from banks, there are a number of alternative funding sources available to those who are starting or expanding their small business. Loans and/or equity investments can be sourced from multiple sources, including credit unions, savings and loans, and private financial companies. Family members, friends, and colleagues are also potential avenues to explore.
Garage spaces are usually not insulated, and garage doors on most homes have very poor insulation. That means it’ll inevitably be super hot and stuffy in the summer, and freezing cold in the winter. To be comfortable in your workshop you’ll need to take the extra step to insulate your garage and set up some space heaters, and some portable floor or window AC units. Having to wear a heavy coat while you work will impede your DIY efforts and nobody likes working in a sauna.
Thanks again for the inspiration. I've just finished putting the door on my 12x16 shop. Aside from shingles it is ready for the winter. I've yet to cut out the hatch for the lumber or start on the interior, but at least it's weather tight and I can work on the rest I the coming months. I am planning to use mineral wool bays for insulation to mitigate sound and ease installation. I don't see a way to add pictures to this reply (I'm on my phone), so I'll try to add one or two later.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
When I built my shop I opted to buy a much higher quality miter saw and table saw than I truly needed at the time.  It ate up a ton of my budget and forced me to put off adding the tools that would allow me to buy cheaper stock for 2-3 years.  During that time my savings buying rough cut lumber would have probably paid for the upgraded equipment I started out with.  
Once again I would like to Thank You for letting so many of us see what is going on in your world. It is very educational and entertaining to see what has happened in the past few months of your dream shop build. As I was watching the video I periodically looked out my window to see the snow falling steadily and building up along the windowsill. Every now and then I imagined I was in your sunny backyard admiring your Shop. I am looking forward to seeing what you will create in your New Space. Keep up the Good work and Congratulations on your Dream Shop.
Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.
The kind of apps that fall into this app type are extensive. Facebook, Instagram, Snapchat, Twitter, WhatsApp, Pinterest, and YouTube are all examples. Remember that some of these apps have been worked on for many, many years. Thus, a v1.0 social app or social networking app will likely not offer all of the same features. For instance, Snapchat did not start with videos, filters, or their "Stories" functionality. A social app would, however, include user authentication, friending, favoriting (or other data interaction), some sort of messaging, and comparable "baseline" functionality.
Enter the garage heater. These space heaters are specifically designed to warm up wide open areas and to function under much tougher circumstances than you’re likely to find in the average house. A well designed garage heater will offer at least 5,000 watts of heating power — enough to warm 750 square feet of space. A smaller heater might take off a bit of the chill, but to really warm your workshop — and keep it that way — you’ll need a heater of this size.

Above all, remember that all of these elements can form part of your negotiation. Unless you are pursuing a highly desired space in a hot rental market, there is usually a point of leverage available to you in every lease negotiation. When it comes to getting the best possible deal in these situations, you’ll want to seek quality professional advice, this will normally include a broker and real estate lawyer.

Food in bear country… When I was in *real* bear country, like in the Sierras, I always kept my food and scented items in the provided bear lockers. Any of the trail heads or camping areas will have bear lockers. Other than that I never really worried about. Just kept it in the cab, yeah. But the Sierras were the only place I went with any considerable bear problems.
But here’s a quick back-story so you know how things went down. The reason I moved my shop so many times was because the sale of our old house fell through at the last minute. This is the house with the original Wood Whisperer shop/garage. We took the house off the market to recuperate and wait for the market to improve. In the mean time, I decided that I should probably make the best of the shop space that I was already paying for, so that’s why I moved my tools back there. When we eventually put that house back on the market, it sold on the first day. That was a BIG surprise! While we weren’t financially (or mentally) ready to build the new shop, I wasn’t about to lose a chance to get that 2nd mortgage gorilla off my back. So all of our resources went into the sale of the old house and the purchase of my mom’s new place. Truth is, there really wasn’t much left to put toward the new shop. Thanks to some financing wizardry, we made it work. But let’s just say I’ll be paying this off for quite some time!
Plywood comes in several different types, the most common being pine and lauan. We used ¼” lauan plywood for the walls in our van. Lauan is cheap, it bends easily, and in our opinion its grain pattern looks nicer than pine. Hardwood plywood like birch costs more than pine or lauan, it weighs more, and it’s more difficult to bend. This type of plywood is a great option for furniture, but we think lauan is a better choice for your walls and ceiling.
Household vacs are not designed to handle large quantities of sawdust or wood chips. Their filters clog up quickly, greatly reducing suction. While you can get away with using a small cordless vacuum for small messes, a shop vacuum offers greater power and capacity. Whether you already own a shop vacuum or are shopping for your first, consider purchasing disposable bags or a washable and reusable CleanStream filter.

I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.
Disclaimer: We spend hours researching and writing our articles and strive to provide accurate, up-to-date content. However, our research is meant to aid your own, and we are not acting as licensed professionals. We recommend that you consult with your own lawyer, accountant, or other licensed professional for relevant business decisions. Click here to see our full disclaimer.
A battery isolator allows your vehicle’s alternator to charge your auxiliary batteries while you drive, and keeps everything separated so you don’t drain your starting battery. Since we installed our Keyline Chargers Dual Battery Smart Isolator, our batteries are almost always fully charged. It’s also very simple to install - the toughest part is running the cable inside your van from the engine compartment.
A battery isolator allows your vehicle’s alternator to charge your auxiliary batteries while you drive, and keeps everything separated so you don’t drain your starting battery. Since we installed our Keyline Chargers Dual Battery Smart Isolator, our batteries are almost always fully charged. It’s also very simple to install - the toughest part is running the cable inside your van from the engine compartment.

Chris Marshall: You’re asking a question that would take many magazine articles or a whole chapter of a good shop-design book to answer adequately. If you haven’t already done so, you might also want to ask this question to the good folks that frequent our forum on woodworking.com. Every woodworker with a shop will have a slightly different answer, so here’s mine. I’ve never had a brick shop, but my last one was a metal pole barn (30 ft. x 40 ft.). I outfitted the interior with 2×6-framed walls and plenty of insulation. It stayed reasonably cool in the summer and warm in the winter, using a wall air conditioner and a 60,000 BTU furnace. Currently, I have a 24 ft. x 42 ft. garage space for my shop. It is framed conventionally with 2×6 walls and stick-built 2×10 rafters. I’ve only been in my new shop for about a year, but it is working just as well or better than my pole barn did, because the new shop has many large windows that let in lots more natural light. I’ve used 8-ft. fluorescent T8 light fixtures in both buildings with good success, and I ran both 110- and 220-volt outlets all around the room. The last shop had a plywood floor; the current one, a concrete slab. I thought I would notice a bigger difference between the two flooring types, in terms of how tired it makes my legs by the end of the day. But in all honesty, a good pair of supportive shoes seems to make the difference moot for me. Both types of buildings benefit from a dehumidifier during humid months (when I’m not running the A/C, that is) to keep the relative humidity low and my tools rust-free. If all things were equal, and money were no object, I would probably go with a conventionally framed wood building over the pole barn. It was easier to build that from scratch as opposed to retrofitting the pole barn framing with walls afterward. But, as I say, the next woodworker will probably offer you a completely different answer from mine. Good luck in your decision!
I’ll throw this suggestion out to you too – while a warm sleeping bag would be a good start, maybe a couple sheets of plywood to put over the truck bed with a tarp over that would provide you some extra protection from rain/snow and also trap in some body heat. You wouldn’t have to make them permanent and could just slide the wood into the bed when not sleeping under it. A cheap bivy as Ryan suggested would also be a good consideration and a quality sleeping pad to provide some warm rating and comfort from the truck bed.

In a woodworking shop, lumber storage is key, and it’s best to design shelves or racks that are about 50 percent larger than you think you need — you’ll almost certainly acquire more materials as the years go on. To maximize a small space, use walls by mounting shelves to the ceiling and purchasing a sturdy step ladder to help you reach things. A wall covered in standard pegboard and outfitted with hooks allows you to customize hand tool storage and keep your most-used hardware within easy reach.
In short – yes. The small business community is a diverse and eclectic collection of mom-and-pops, multi-generational businesses, one-stop shops, trendy boutiques, food trucks, lemonade stands, wine stores, bicycle stores masquerading as bars, and more. These entrepreneurs come from every walk of life and their motivations for starting small businesses are as unique as the businesses themselves. If you’re reading this, chances are you’re looking to join their ranks, and we say: “Go for it!”
Another flexible option is the portable work tables the guys are building back in our shop. This gives us a work surface that we can move wherever we may need it. Now the main workbench we’ve left a little gap between two of the cabinets for a trashcan or a stool to slip in but we did need to support the countertop where it crosses so Tim and Chris are adding some 1x4s to bridge the space. They’re also putting in a 2×4 inside one of the cabinets where the two pieces of plywood will have to be seamed. Then it’s just a matter of laying in the pieces in place and nailing them down to the cabinet. That trim strip around the edge is mostly for looks but the cedar backsplash along the back will keep us from banging up the wall or getting small items stuck between it and the counter. All in all it started to look pretty good.
Ok Rob let me try again .I would suggest you sign up for a community collage woodworking class or a woodworking coop where you can use the tools you will need to build the kind of items you have in mind. You say you have used the tools you listed but that could mean only used them once or twice. If you have minimal experience with tools and woodworking that might be another reason to take a class assuming there is one available . Do you have a space you can use as a shop ,a garage,carport etc? As far as tools and equipment are concerned I think Knotscott covered it very well. I know your supposed’s said you couldn’t find tools on Craigslist or garage sales but those might be the place you can make an offer on a shop full of tools in the price range you trying to stay in possibly with some materials and other extras. It might even work to put a wanted wood shop full of tools in the tools section of your local Craigslist.
You see, everyone can make money with his/her hobby, and I am going to reveal it to you in a minute… Ultimate Small Shop Ebook Download There are millions of people who have the same hobbies and interests just like you. Everyone is searching for more information about their hobbies and passions. Take a guess – what is the best place to find the information today? I think you will agree that the World Wide Web (the Internet) is one of the best places on the Earth to look for information related to your hobby. Millions of people use the Internet to find the answers to the questions they have, to solve the problems they encounter every day. So, how could you make money with your hobby? It’s simple – build your own web site (online business) about your hobby. Ken Evoy, internationally acclaimed Internet marketer, developed a system – SiteBuildIt! (SBI!) – that helps anyone to create professional websites about his/her hobbies, interests and passions. Hundreds (maybe even thousands) of SBI! users have already quit their jobs and now are making a living from the comfort of their own homes, doing what they love – creating web content about their hobbies. Each web site built by SBI! is search engine optimized. It means that when you build your own web site with the SBI! tools, the traffic to your web pages is guaranteed through search engines. And it doesn’t matter what your hobby is – Ken takes you by hand and explains how you can make money from the traffic received to your web site. What matters is – you create information-rich content pages about what you know and love – about your hobby! Ultimate Small Shop discount If you think that you cannot write web content – forget it, you can! – SBI! will guide you step-by-step from developing your web site’s concept to brainstorming hundreds of profitable related keywords; building a themed web site; generating motivated, targeted search engine traffic that wants to click on your recommendations, links to the related products sold by merchants that you will represent. Note that this is not a “get rich quick” scheme. It will require lots of your energy, work and time. The bottom line is that you will have a hobby that makes money for you!I’ve always liked to make gadgets and gizmos that have some function, either useful or not so useful. It started with the simple things that many kids make – slingshots, a simple bow, and arrow, a toy boat. Occasionally I made more involved items such as a canoe and a dune buggy. Then there was the grass hut – 12 feet across, octagonal in shape, and thatched top to bottom with a thick layer of grass. I built it in a remote location, near a strip mine filled with water. Hauled the cut grass in a 1972 Volkswagon convertible with the top down. Piled the grass high in the back seat. It must have taken a dozen trips back and forth from a nearby hay field. Simple things appeal to me more than costly homemade items. A small project lets me pursue an interest without interfering with other goals. Ultimate Small Shop Tips A project with a small amount of time invested seems more like entertainment.
So you stayed up all night, thought long and hard, and decided you want to name your designer sunglass hut The Sunny Rabbit. We don’t blame you, it’s a pretty cool name. Most would tell you that the next and most logical next step is to register your business as a DBA or at the state level. But, we’re here to tell you that’s wrong! Here’s why. We just talked about how the right business name can make or break your brand identity and in today’s digitally connected world, securing your brand identity across the web is equally as important.

If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.
×