We first obtained legal permission from Hasbro [which originally developed the Transformer toy line back in the 1980s] to build it late in 2015. I also had to obtain my commercial driver’s license (CDL), so I spent a few months learning how to drive a truck while simultaneously spending the winter of 2015-16 working with Western Star to piece together on paper a vehicle that mirrored the Optimus Prime truck. Once the factory delivered the truck in April 2016, we got to work on the customization and fabrication right away. It was roadworthy again by October 2016. So the entire process from start to finish was about a year.
I’ll throw this suggestion out to you too – while a warm sleeping bag would be a good start, maybe a couple sheets of plywood to put over the truck bed with a tarp over that would provide you some extra protection from rain/snow and also trap in some body heat. You wouldn’t have to make them permanent and could just slide the wood into the bed when not sleeping under it. A cheap bivy as Ryan suggested would also be a good consideration and a quality sleeping pad to provide some warm rating and comfort from the truck bed.
You’ll want to consider your insurance needs both in terms of the potential frequency of claims against you and the size of the potential liability. You’re also going to want to think carefully about your assets and what you can and cannot afford to lose. A good rule of thumb is to always buy insurance if you can’t absorb the loss of a particular asset without dramatic effect.
I framed in a 4x8 Garden Shed on the back. I didn't want it so deep that stuff would get buried in it. I need to take an updated picture of the back. These pics were from early on and I have changed some things in the organization. I used similar framing techniques and built a lean to roof attached with metal hangers. I chose to use clear corrugated roofing to allow natural light into this shed. You can see the 2 shopvacs that were originally part of my simple vacuum system. I have removed them and found that I get better airflow using an electric leaf blower with the vacuum attachment hooked up to my system. There is a large metal trashcan with a dust collection separator to collect the larger pieces of saw dust and chips. My air compressor is on a shelf on the right now and I ran a hose through the wall and to a 25 foot reel attached to the ceiling. I wired separate switched for both on the inside of my shop. These systems work extremely well for a small shop. The wall provides some insulation from the overwhelming noise they would otherwise create inside the shop.
Well, I hate pegboard, pegboard’s in every shop, people use the heck out of it. And what I wanted to do was start moving the tools in, get a few of them in and then maybe just build some little racks for the screwdrivers and a few of the things like that. But things that are like categories – like a drill, drill bits – just let the drill bits be right here. Certain things maybe that you don’t use all the time, hole saws or maybe brass for something like that, can go down in other drawers.
When Julie Owen bought Cocobolo Interiors in 2008, she set about adding more contemporary items to the Armonk, N.Y., shop. But with only 3,000 square feet, she struggled to figure out where to put her expanding line of furniture, lighting fixtures and accessories. Her solution: create sections within the shop and arrange the furniture the way customers might imagine it at home, using low bookcases and folding screens as dividers.
There are a variety of structures to choose from when starting a small business. However, the most common business structures include sole proprietorship, partnership, corporation, and S corporation. The structure you choose determines which income tax return form you have to file, which, you guessed it, dictates your legal and financial responsibilities as a small business owner. Because of this, you’ll want to make sure you understand the options that are available to you and weigh the pros and cons before incorporating your business.
For those of us building apps, there's an increasingly larger burden on us to meet the expectations of our users. We've outlined the considerations of what makes a great app in the past, which are more relevant than ever. Users simply don't have the patience for apps that are overly complex, slow, or buggy. The best apps are personalized, highly contextualized, and touch human emotion. Meeting those user expectations is significantly challenging.
The primary investment of any garage workshop are the tools. Protect your investment with a high quality tool chest that is neatly organized and (if needed) lockable. Look for smooth rolling ball-bearing drawers, and if you’re buying used, beware of rust and dirt that could corrode your tools. We recommend installing drawer mats to keep your tools from sliding around. They also give your tools a softer cushion to rest in.
You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.
Thankfully, the tools we use continue to get better and more app specific. For example, Sketch lets us design more efficiently with its focus on creating user interfaces. Marvel helps us craft better prototypes with it being specifically for apps. Swift has been a revelation for the Apple ecosystem and has expanded developer interest considerably. Android Studio and now Kotlin are doing the same for Android apps. Firebase and yes, even Parse, now as Parse Server, helps developers build app-focused backends to bring apps to the market more quickly.
Really enjoyed watching the video of the shop build. You will be turning out great pieces in no time. At the end of the video it looks like you have your dust collection system up and running. Where did you purchase the duct work? I thought I remember you talking about this in the old shop. Did you use regular HVAC 4″ round duct or a heavier piece. Thanks for the insight and good woodworking.
This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.
Non-Standard Miter Slots - This one is a downer. One of the primary advantages of having a table saw is access to jigs that expand the saws functionality. This is a major issue if you plan on buying after market jigs. Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list. Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.