So far it has worked out. It's probably not ideal. I imagine a system would work much better, but it gets the job done until then. I ended up setting up in my small 1 car garage as well now. I used two shopvacs to build a system in there. I have a few new Instructables to put together and a new shop tour to do as well. Thanks for the comment! FYI: The wood storage has passed the time test. I have not had to change a thing about it. I plan on adding a shelf above the sheet goods to store thin moldings and cut-offs. I still find it incredibly easy to access my wood quickly with that setup. I have to move stuff around in the garage to get to my wall mounted wood storage, so it's more of a pain.
Hey Kasey, I don’t do anything for insulation, I treat truck camping just as I would cold weather tent camping. Just bring a good sleeping bag and learn how to manage in the cold. Usually the side wall of the truck is not at a perfect 90 degree angle, so you will need to check out the angle and compensate. You can hold up a small piece of 2×4 at the back to judge the angle and make a few test cuts to ensure it sits “flat” aka level.
This will be a personal matter, depending on whether it will be helpful for finishing or sharpening. However, it is a good idea to look beyond your current use of this space to the next owner. Would it be beneficial to add plumbing hookups so that the shop could someday be an apartment, or an art studio, or an extension to your house? It could add to the resale value of your house to be able to create as flexible an area as possible by roughing in a bathroom and even a kitchenette area if you can. If this is done when wall cavities are open or before the slab is poured, your forethought could pay dividends but not cost much up front.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette package. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provincial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effectively through your drawings that your structure will comply with the technical requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
Becoming a small business owner is one of the most rewarding and inspiring journeys a human being can take. It provides you with a chance to be your own boss, take control of your financial destiny, and become a meaningful contributor to your local economy and community. There will always be a reason not to take the plunge. But if there is one rule of small business — and life — is that nothing will happen if you don’t make it happen.
Hey there Ryan. Cool blog! I love the idea of trucking-it! I’m not able to do something like that, though I wish that I had taken the time when I was younger to do so. Here’s a suggestion that you might consider, if you haven’t already considered it before: Obtaining and using a hammock. I’d suggest bolting in an eye hook on the truck, or using the bumper as a tie point if you don’t have a second tree around. Also, in the high desert, you could use rocks as anchor points for it. Just an idea, from one camper to another.
From building websites for other small businesses to providing technical support for certain projects, quality web development is in high demand right now. With such a technical skillset, make sure you can describe what you do and how you will do it in easy-to-understand language. Test your messaging on friends and family who don’t have a firm understanding of the work you do.
Hey Ted! If you mean to ask whether you could sit up from one of the vertical sidebins and have enough headroom under the Leer 122, I think that would be a no. You’d have to build the sidebins to be a little shorter. At least with my truck, that would be the case. Perhaps with a full-size pickup you would have enough room thanks to the overall size increase of the canopy as well.
Ultimate Small Shop is a complete guide to setting up your own workshop, from the planning phase to optimizing it for business. You’ll learn how to put together a complete and functional workshop for less than you expect. Ralph aims to get your shop set up for less than $1,000. Ultimate small Shop includes suggestions on where you can get the tools and equipment needed at the most affordable prices and how to optimize space to get the most out of the little room you have.
Depending on your situation, you may need to upgrade to 200 amp electrical service in order to meet the needs of your house and your shop. It may also be in your interests to add in a separate electrical service meter on your shop so that you can clearly write off electrical use for your business, or in future rent the space out and clearly separate out the utilities for billing your tenant. Generally, you don’t want to skimp on the power to your shop or on the lighting you include.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking. These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email firstname.lastname@example.org and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence.
Electricity was something we didn’t want to worry about at all in our van, so we went big from the beginning. We bought Renogy's 400-watt solar kit and two VMAX 155ah batteries. We mounted three of the panels on our van’s roof, and the fourth we attached to a folding stand made out of PVC so we could roll it out as needed. While the system works great and keeps us charged up, in hindsight it was a little bit of overkill - especially since we added a battery isolator.
If you are going to apply for a trademark, make sure to conduct a comprehensive search, like the one mentioned in ‘Securing Your Business Name’ to ensure no one is already using your proposed name in a similar capacity. The United States Patent and Trademark Office also provide a simple search tool that will quickly let you know if you’re potentially infringing on someone else’s turf from a legal point of view.
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wiring for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to finishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a programmable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.