Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appro­priate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with hom­eowners and builders to make sure that the work will meet code and will endure.

Power outlets are also needed for lighting, heaters, AC units, radios, televisions, CNC machines, 3D printers, and computers—all of which you’ll find in many workshops (although maybe not together, and maybe not all in your garage.) You simply can never have too many outlets and it’s much safer to have too many than not enough. Bring in an electrician to help install your outlets and setup 220v power if needed for larger shop tools.


Pegboard panels like this are extremely popular way to display and store hand tools. But they have one annoying problem is that when you lift off a tool, often the hook itself will pop out of the board. And that happens with over a number of times, every time you reach for a tool it can get pretty annoying. So you can buy at the hardware store, they make straps and special devices to hold the hook in place, but I’ve found this works just as well and it’s a lot cheaper.
So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.

You may want a garage door if you will need to access your shop with large workpieces or tools, or if you or future owners will ever want to use the space to park a vehicle. Garage doors are notoriously drafty, however, so if you think you can live without one you will probably be warmer. Instead, you could opt for out-swinging double doors. In a small shop you can, at a pinch, rip longer lengths of lumber by feeding the material out of either a strategically placed door or window.
An exclusive arrangement is one where the tenant works exclusively with one broker for a 3 – 12 month period. During this time, the tenant can’t work with another broker. A commission between the tenant and broker is negotiated, equal to a small portion of the expected tenant broker fee. However, this commission is paid only if there are no tenant broker fees.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.

In our opinion, having one of these is an absolute must for living on the road - especially in humid areas. To fully cover the width of a van’s side doors/back doors, you’ll need a larger screen that’s designed for French doors. If your vehicle has a smaller door opening like an RV, a screen meant for a standard door will work fine. We could only find standard door screens, so we bought two and hot-glued them together to cover up our side door.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).
Do you create, collect, or curate anything special? Consider starting an ecommerce store and turning your hobby into a full-time job. Whether you need somewhere to sell all that pottery you’ve been making, or an excuse to search for the sports memorabilia you love tracking down -- an ecommerce store can make it financially viable for you to pursue your passion.
Most businesses must obtain a variety of business licenses, permits, and registrations before opening their doors to the public. As a small business owner, it is your responsibility to ensure that you are abiding all the laws and regulations applicable in your state and to your particular industry. You also have to research and apply for all relevant permits and licenses that apply to your business type and location. Remember, it is impossible to plead ignorance as a defense. It’s up to you to educate yourself. When in doubt leave it to the professionals. CT Corporation offers custom license packages that simplify the process for business owners. Click here for an example of what that looks like.
Above all, remember that all of these elements can form part of your negotiation. Unless you are pursuing a highly desired space in a hot rental market, there is usually a point of leverage available to you in every lease negotiation. When it comes to getting the best possible deal in these situations, you’ll want to seek quality professional advice, this will normally include a broker and real estate lawyer.
I have a plastic bed lining on my truck, which also covered the back of the tailgate… I just popped the screws off, took off the plastic liner and drilled holes in the sheet of plywood to match those used by the plastic tailgate cover. Sorry if that doesn’t help you with your setup. But I’m sure you could just drill your own holes in the metal tailgate. Use the plywood cover as a guide for your screw holes…
To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.
This will be a personal matter, depend­ing on whether it will be helpful for finishing or sharpening. However, it is a good idea to look beyond your current use of this space to the next owner. Would it be beneficial to add plumbing hookups so that the shop could someday be an apart­ment, or an art studio, or an extension to your house? It could add to the resale value of your house to be able to create as flexible an area as possible by roughing in a bathroom and even a kitchenette area if you can. If this is done when wall cavities are open or before the slab is poured, your forethought could pay dividends but not cost much up front. 
As always, great article! While my dirtbag adventure will likely only be about 6-7 months, I am starting to wonder about logistics. You mention that most people use the automobile they have. I drive a Prius. Not ideal for sleeping in, but I’m a pretty content ground dweller. I know that long-term I may start to question this. Here’s the proposition I’m considering: by saving on gas (45-50 mpg), I can occasionally cough up the money for lodging when I feel the need for added comfort. I can definitely do the number crunching, but I’m wondering if you’ve encountered people doing this or did similar analyses of your own at any point. I’d love to hear any insights you may have on this.
Equity financing is money raised in exchange for a share of ownership in your business. The core benefit of this type of funding is the lack of debt. You won’t have to worry about those pesky monthly repayments. The downside? You are giving up total ownership of your business, you are giving up the rights to a portion of the ongoing profits of the business, and you are potentially giving up some control of how your business is run (Though this is not always the case).
After years of digging down under router tables, lifting the entire unit up to change bits, and then fighting to get the plate flush again in the table, I chose to spend the money to pur­chase a router table, fence, and lift system. I did a thorough review of these systems, and chose the Canadian made Jessem Rout-R-Lift II kit. The system comes with a solid steel stand, a phenolic table, an adjustable extruded aluminum fence, and their base model lift system. For budget reasons, I did not choose the hefty Mast-R-Lift, but I am quite happy with the lighter Rout-R-Lift II. It will last me a couple of lifetimes, so it is the right system at the right price for me in my one-man shop. Hats off to Jessem for making a great lift at a very rea­sonable price in the middle of a tough economy. The table is durable, and flat. The direct drive lift is smooth and precise. I mated the lift system to a mid-sized model 690 Porter Cable router, which has a fixed speed, and enough power to do any­thing I need. The Jessem system uses a bayonet type mount for the table inserts, a nice touch that makes swapping the table insert quick and simple. As with all my machines, the router table is connected with the supplied dust port to my shop dust collection system with automated switching. 
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
However, instead of sharing a remodel update this week I thought I would do something a little different. This little voice in my head (sometimes called my husband) has been nagging me to add videos to my blog. I did a couple 1 minute hands-only videos a few months back, but I have been seriously afraid to get in front of the camera. The nagging voice finally won out and I bit the bullet and got in front of the camera for you today! I decided to do a video for today’s post instead of just writing out a boring list. And while editing the video I came to the realization that I am very expressive when I talk. Wow! I use my whole face when I talk. I guess that’s what people meant when they said I am dramatic. Oh well, this is me so I hope you enjoy today’s video about how to build a woodshop on a budget.
You see, everyone can make money with his/her hobby, and I am going to reveal it to you in a minute… Ultimate Small Shop Ebook Download There are millions of people who have the same hobbies and interests just like you. Everyone is searching for more information about their hobbies and passions. Take a guess – what is the best place to find the information today? I think you will agree that the World Wide Web (the Internet) is one of the best places on the Earth to look for information related to your hobby. Millions of people use the Internet to find the answers to the questions they have, to solve the problems they encounter every day. So, how could you make money with your hobby? It’s simple – build your own web site (online business) about your hobby. Ken Evoy, internationally acclaimed Internet marketer, developed a system – SiteBuildIt! (SBI!) – that helps anyone to create professional websites about his/her hobbies, interests and passions. Hundreds (maybe even thousands) of SBI! users have already quit their jobs and now are making a living from the comfort of their own homes, doing what they love – creating web content about their hobbies. Each web site built by SBI! is search engine optimized. It means that when you build your own web site with the SBI! tools, the traffic to your web pages is guaranteed through search engines. And it doesn’t matter what your hobby is – Ken takes you by hand and explains how you can make money from the traffic received to your web site. What matters is – you create information-rich content pages about what you know and love – about your hobby! Ultimate Small Shop discount If you think that you cannot write web content – forget it, you can! – SBI! will guide you step-by-step from developing your web site’s concept to brainstorming hundreds of profitable related keywords; building a themed web site; generating motivated, targeted search engine traffic that wants to click on your recommendations, links to the related products sold by merchants that you will represent. Note that this is not a “get rich quick” scheme. It will require lots of your energy, work and time. The bottom line is that you will have a hobby that makes money for you!I’ve always liked to make gadgets and gizmos that have some function, either useful or not so useful. It started with the simple things that many kids make – slingshots, a simple bow, and arrow, a toy boat. Occasionally I made more involved items such as a canoe and a dune buggy. Then there was the grass hut – 12 feet across, octagonal in shape, and thatched top to bottom with a thick layer of grass. I built it in a remote location, near a strip mine filled with water. Hauled the cut grass in a 1972 Volkswagon convertible with the top down. Piled the grass high in the back seat. It must have taken a dozen trips back and forth from a nearby hay field. Simple things appeal to me more than costly homemade items. A small project lets me pursue an interest without interfering with other goals. Ultimate Small Shop Tips A project with a small amount of time invested seems more like entertainment.
1. My vehicle is a Ford F-150, which is not great for off-road travel but is by far the best I’ve ever had for mobile living. The 6.5-foot bed is perfect for my 6+ foot height, and I can probably haul everything I own other than my home furniture in the back of it. How long is the bed of your Toyota? I’ve always assumed a small pickup would tight length-wise for comfortable sleeping.
Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regula­tions, a larger lot, or more congenial neighbours. 
The kind of apps that fall into this app type are extensive. Facebook, Instagram, Snapchat, Twitter, WhatsApp, Pinterest, and YouTube are all examples. Remember that some of these apps have been worked on for many, many years. Thus, a v1.0 social app or social networking app will likely not offer all of the same features. For instance, Snapchat did not start with videos, filters, or their "Stories" functionality. A social app would, however, include user authentication, friending, favoriting (or other data interaction), some sort of messaging, and comparable "baseline" functionality.

I save all my back issues of The Family Handyman magazine and love the projects and repair tips. The trouble is, I’m not always ready to do the project when the issue arrives. To make my favorite articles easy to find at a later date, I put a stick-on label on the cover and then add notes for easy reference when the time comes to do the job. — Willie Schreiber. Plus: Check out this small workshop storage solution.
My enthusiasm was kindled and I made friends with Surrey Timbers for more 'exotic' wood. My next purchases were a Drill Press and a Scroll Saw from Axminster Tools and I set to work. An excellent piece of Yew followed by some Thermal Ash has so far produced 4 cribbage boards. I then obtained a Palm Router which, after some practice, I find better for the more intricate work.

Do you carry items that bring your customers back time and time again? Consider placing these primary and similar secondary product lines toward the back of your store. Or, if your stock is constantly changing and you don’t carry replenishing goods, place your sale items toward the back. That way, customers must pass your new items and promotional displays on their way to check out the deals in back.
Will this make me money? If it will not, cross it out. If you want to keep it on, please rephrase your goal so the outcome can be money driven. For example: Grow Instagram following (bad) vs. use Instagram to drive traffic and sales to website (winner!). This way, you can break that goal down into tasks ( ill show you that in an another step) and those tasks will lead to you actually making money with that goal instead of with just a larger Instagram following.
In the summer months, your windows will be one of the primary ways that heat gets into your van. Because of its reflectivity, Reflectix works great as a window covering to reflect radiant heat away from your windows. And, if you’re concerned about height in your van, layering Reflectix under your subfloor is a good way to add a little insulation (R-1.1) without sacrificing headroom.
To help, I’ve pulled together 40 small business ideas for anyone who wants to run their own business. Use these as a jumping off point to spark your own unique ideas.And if all else fails, live the words of Airbnb Co-founder Brian Chesky: “If we tried to think of a good idea, we wouldn’t have been able to think of a good idea. You just have to find the solution for a problem in your own life.”
With such an unstable job market and it being harder to get employed, more people are moving into entrepreneurship and being self-employed than ever before. Woodworking is a fantastic business opportunity, but you might feel that you don’t have the space or money to set up your own workshop and sell your goods. If that sounds like you, then you should check out Ultimate Small Shop by Ralph Chapman.
Many retail fixture and display companies provide store planning and design services to their customers. Though typically not free, these in-house design services can be far less expensive than hiring an independent designer. Plus, they can help streamline the process of store layout and planning, along with the purchasing and installation of displays and fixtures.
Budget Toilet: Luggable Loo. With the Luggable Loo from Reliance Products, you can turn any 5-gallon bucket into a portable toilet for your van. Make sure to line your bucket with a trash bag or toilet waste bag - then once you’ve done your “doodie” just tie up the bag and dump it in the trash. Reliance also sells deodorant chemicals that will make it easier to live with your new roommate
Use this model whether you’re looking to turn your team of one into a two-person shop or you’re hoping to build out your marketing department to a team of 10 or more.  By focusing on the skill sets your business needs to be successful — rather than on the resume of an individual candidate — you’ll ensure vital functions are covered while expanding in a sustainable way.
I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino 

Reflectix only works if there is an air gap next to it - Reflectix themselves recommend at least a ¾” gap between their material and the area to be insulated. This is the case because Reflectix is a radiant heat barrier, and when you put it right up against your van walls the foil cannot reflect back radiant heat (remember, radiant heat is only transmitted through air or a vacuum). If there is not an air gap, the insulating power of Reflectix is very low.


In my opinion, the best shop space is a flexible one. I know many folks expected that after setting up my shop so many times, I would be able to design the PERFECT shop space including a finishing room, a dust collection closet, and even some internal walls. But the truth is, the most important lesson I learned over the years was to expect change. My shop is not a static entity. It is more like a living breathing creature that adapts, evolves, grows, shrinks, and changes configuration. Committing to an internal spacial arrangement too early could yield disappointing results. This is why you won’t see me placing dust collection ductwork in the floor. I need to work in a space for at least a few months before I can be confident in my initial setup. Even then, I fully expect things to change at some point. If I made too many restrictive and/or permanent decisions ahead of time, these changes could be difficult or impossible to implement. So my best piece of advice is to forget about the concept of perfection. Instead, focus on flexibility. The ideal shop, in my mind, is little more than 4 walls, a roof, and a butt-load of outlets and lights. So here are some of my basic general goals for my new shop space.
A battery isolator allows your vehicle’s alternator to charge your auxiliary batteries while you drive, and keeps everything separated so you don’t drain your starting battery. Since we installed our Keyline Chargers Dual Battery Smart Isolator, our batteries are almost always fully charged. It’s also very simple to install - the toughest part is running the cable inside your van from the engine compartment.
Many small businesses in New York and New Jersey were forced to close following Superstorm Sandy because they lacked the insurance that would have gotten them back on their feet. That part is well known. What’s less well known is that this lack of proper insurance, coupled with the lack proper legal incorporation, resulted in many entrepreneurs seeing their personal assets come under threat.
For the large square windows near the tailgate I just used those big “magic auto shades” like these, which fit perfectly to cover up those side windows and the back window by the tailgate (I had four in the canopy) and another set up in the cab for my actual window. As for the longer side windows I just used a USPS box, haphazardly stuck up against the window. Nothing fancy.

Well, my workshop is finally complete and I’m ready to take on just about project that comes down the line. And I’m pretty well set up here. I’ve got a great workbench, plenty of table space over here that easily rolls around the shop if I need it, lot of storage space down here, I can tuck these tools away or bring out any new ones that I need. And as you can see I’ve got plenty of supplies to tackle just about any project.


This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.

You can see I broke the ultimate goal down into smaller tasks. Now you just need to do this for all the big goals that you have mapped out for the year. You may have more ideas or goals throughout the year and that’s okay. With this type of document, you are able to add another category and tasks anytime you want. This is just the best way to keep track of all the little things you need to do to accomplish your goals so you never are stuck wondering what you have to do next.

It looks great. Your little guy looks like he's having fun. I just had over 50 kids come through my shop last weekend to do some woodworking for cub scouts. I am saving left over insulation to put in there soon. I restocked my plywood recently too. The pieces of pipe made it much easier to pack in a lot of heavy pieces. I also took the time to measure lengths and mark the ends of all my lumber in the hatch under my bench to find what I need a little easier. My $100 8x8 needs a little TLC soon. But the shop is still rock solid. If you plan on making a lot of dust, I would also suggest a diy air filter with a box fan and a cheap air filter. It helps a little.


Plywood comes in several different types, the most common being pine and lauan. We used ¼” lauan plywood for the walls in our van. Lauan is cheap, it bends easily, and in our opinion its grain pattern looks nicer than pine. Hardwood plywood like birch costs more than pine or lauan, it weighs more, and it’s more difficult to bend. This type of plywood is a great option for furniture, but we think lauan is a better choice for your walls and ceiling.
In an indoor or basement shop with industrial carpeting, lay down inexpensive laminate flooring to make your life a bit easier at the end of the day. Be sure to anchor the panels or place a large rubber mat beneath to keep them from sliding over the carpet. (Covering up your carpet is even more critical if you want to go beyond wood and work with a material such as aluminum in your indoor shop; metal shavings dig into any kind of carpeting and are incredibly frustrating to clean up.)
First, decide on wax you would like to start with, there are three different kinds to choose from Ultimate Small Shop paraffin wax, soy wax, and beeswax. Paraffin wax is most commonly used in candles, this wax is found at most candle making stores. Soy wax is all natural, made from soybeans, and cleans up easily with soap and water. Beeswax is all natural too, and making beeswax candles is often easiest because you simply wrap a sheet of beeswax tightly around a wick then seal it with your thumb, which means no melting is required. To begin, spread newspapers around the candle making area. First, you melt your paraffin or soy wax and it must be double-boiled. Usually, you place a large pot that is about half-filled with water on a burner over low-medium heat, place a melter in the water, then gradually place wax pieces into the melter. When the wax has melted, you can add coloring or fragrance as desired. To make molded candles, cut the wick two inches taller than you want the candle to be, then thread it through the hole at the bottom of the mold, then plug the outside of the hole with putty. Place a pencil or similar item over the top of the mold and tie the top of the wick to it, centering the wick. If the mold is cardboard, plastic, or glass, heat the wax to 130 degrees Fahrenheit. If the mold is metal, then heat the wax to 190 degrees. You can use a candle or candy thermometer to measure this. Ultimate Small Shop Pdf When the right temperature is reached, lift the melter by the handle and slowly pour the wax into the mold. Let cool for twelve hours then refrigerate for twelve more hours, then your candle is ready to be removed. To make votives and other small container candles, you can use pre-tabbed wicks by simply placing them in the center of the votive candle molds or containers, then pour the wax mixture over and let stand for twelve hours, refrigerating the votives. By the time your teen is in high school, you probably aren’t taking as many pictures of them as you used to. I have to keep reminding myself that I only have a couple of years left and no time to waste trying to capture fleeing teenage memories. You might be thinking that I’m really organized to be already working on scrapbooking my daughter’s high school memories. To be honest, I have a shoebox full of pictures of my daughter waiting for me to get to someday. But if I wait until “someday” to continue taking pictures because I already have so many pictures I haven’t done anything with, then my daughter’s teenage years will come and go while I try to catch up. I don’t want to chronicle every detail of my daughter’s life (nor would she want me to!), but I was trying to think of some memories that she might want to laugh about and maybe even treasure someday. Ultimate Small Shop Guide Woodworking So how do you do that without ending up with pages and pages of memories? I decided to do two large (12×12) pages (facing each other in the album) for each year of high school.
As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
Most of today’s POS systems have integrated inventory management software that allows you to put hours back in your week, whatever the volume of your stock. A quality point of sale system will allow you to manage pricing changes, track product availability, cross-check inventory, and automate reorders with ease. All of which are crucial in helping you develop a deeper understanding of your business, enabling smoother day-to-day operations and smart purchasing decisions.

Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Even if a website and social media aren’t part of your immediate plans for launching a business, as a savvy 21st century entrepreneur, you want to make sure that you have complete ownership of your brand identity before paying any fees required to register your business. Using the example of The Sunny Rabbit, at the very least, you would want to run an online search to ensure that TheSunnyRabbit.com is available. Assuming you want to join the other 50 million small businesses marketing to customers on Facebook, you’ll also want to make sure that Facebook.com/TheSunnyRabbit is also available.
At least once a year I want you to set aside some time (I’m talking about a large chunk of time - like a day) and I want you to write down everything you want to accomplish this year or next year (or whenever you are planning for). I tend to plan for a whole year, but you can try 3-6 months to help you get started. Take away any and all distractions because it’s important that you are super focused on what you want to accomplish for the year. This is the time to let your ideas flow, don’t hold back. Things on this list can include: Launch your own website, release a new invitation line, and work on my Instagram account. Don’t overthink, just write down what comes to your mind and whatever your heart desires. There will be time later to refine what you have written down. When you are starting to brainstorm your goals, I would suggest that you first start off writing them on a notepad like this. And then once you are done, you can move them over to a task organizer like this.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Ordinary clip-in-place shelf brackets with slotted metal supports can hold a lot of weight. But some-times they’re unstable and can be easily knocked loose. The play in the slots allows the bracket and shelf to shift from side to side. To prevent this, use your circular saw to cut 1/8-in. deep slots into the undersides of the shelves, aligned with each bracket. When the shelf is assembled, the brackets fit into the slots, eliminating the sway. Also check out: How To Build Floating Shelves.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
Well, I thought about that I don’t want all that dust to kind of infiltrate everything else in the building. So actually instead of putting in some kind of dust collection system, I thought that I would probably just put a nice shop vac here. And then I have room that I can bring some hose back behind this column and then you know if you’re sitting here working on something we can have adapters that go right into a miter saw or right into a sander or have a little outlet more or less to lay up on the counter that would collect all of the dust. And the same thing could happen on any of the work we do out here.
Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on.  The rewards aren't usually good enough to compel me to purchase on their own.  But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.
Plus, taking the time to put pen to paper should benefit you as the small business owner as much as any potential new employee. Creating this kind of central resource about best operating practices will force yourself to formulate your thoughts and be clear about exactly what you want. Whether that means codifying sales procedures or deciding who can take cash from the cash drawer, you’ll have a clear and consistent company policy, something to which most employees will respond favorably.

Ultimate Small Shop is a complete guide to setting up your own workshop, from the planning phase to optimizing it for business. You’ll learn how to put together a complete and functional workshop for less than you expect. Ralph aims to get your shop set up for less than $1,000. Ultimate small Shop includes suggestions on where you can get the tools and equipment needed at the most affordable prices and how to optimize space to get the most out of the little room you have.
Every woodworker (I think!) dreams of someday being able to construct their own dedicated woodworking space. To date, I have bounced around from garage to garage (about 4 times), making the best of a crappy real estate situation. And while I have been lucky to have fairly large spaces to work in, I still daydreamed about the possibility of designing a shop from the ground up, with both woodworking and video production in mind.
Once you’ve got that, you’ll want to familiarize yourself with your tax obligations as a employer, including providing required employee benefits such as social security and workers’ compensation. As an employer you are also responsible for withholding federal and state taxes from your employees’ paychecks. What’s more, you are obliged to ensure all withheld tax is forwarded to the government within a defined time frame (usually a matter of days after the paycheck was issued). Failure to do so can result in a fine.
Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.
×