The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.
I totaly get not wanting to get into the cost part of the shop. We just went through a house renovation, and my stock answer to the ‘how much’ question is either ‘enough’, or ‘enough that was right for us’. There is a quality of life or utility aspect that every person needs to figure out for themselves. And, I would think not having to bounce around from garage to garage anymore has gotta be worth something!
I framed and sheathed each wall individually and then stood them up with the help of long 2x4 braces.  My neighbor let me borrow his framing nailer, which made things go much faster.  I added a second cap of 2x4 on the top to make the walls a little more rigid.  I then laminated 4 2x4's to construct a ridgeboard.  I nailed in some temporary 2x4 supports and had a friend help lift it into final position.  Once all of the rafters are cut and nailed into place, the supports were removed.
This OXO palm brush really helps us conserve water while washing our dishes. We fill the reservoir with water and a few drops of Campsuds, and we only squeeze out what we need - so it takes care of both the initial rinse and getting our dishes soapy with minimal water usage. It’s also very compact, and the comfortable shape makes it easy to scrub dishes.
Tim Inman: You don’t say where you will be located, but if you are anywhere that gets cold I definitely have a suggestion. I’ve built three shop buildings over my years. In each one, I’ve put down 2-inch closed cell foam board underneath six inches of concrete for the floor. I would never build a shop — or anything else, for that matter — without this. The foam lets the concrete become a huge heat sink and warming stone. My feet are never ever cold when I work on this combination. The shop stays reasonably warm without spikes in the heat and cooling. The tools are more rust-free, and I like it.

Love the design. I’ve got a 15 tacoma, which has rails that run the length of the bed and are what my shell is “clamped” into via a bed rail nut. Hence my problem with following your outline verbatim. Any suggestions for incorporating the rail as a substitute for the 2×4 you clamped into your truck? Essentially connecting the 3, 2×4 braces directly to the rail… I’m a construction novice, any suggestions greatly appreciated!
It does sag a little bit, but not worryingly so. As I mentioned, it often rests on top of the large plastic boxes I place underneath, and I put in a small wooden brace at the entrance. You could definitely build it slightly smaller, or put in a more substantive center brace — like a sheet of plywood that fits into the groove of the bed liner and is the exact height you want.
Hand tools offer the finesse and precision you just can’t get with anything else. There’s a sense of satisfaction you get from working the wood rather than machining it. After all isn’t that why you got into woodworking? Again there are a vast array of tools but narrow it down to a core range and you’ll have the confidence to complete a number of jobs.
When you are looking for small business funding options, be it from the local bank, an angel investor, or even a family member, the first thing you will be asked to present after your business plan will be any existing financial records. Make sure you are putting your best foot forward by keeping meticulous records, with your business finances completely separate from your personal finances.
Well I’ve been kind of fighting that, because I wanted to keep it open to where you could have the flexibility of moving things in and out. It probably makes sense. Actually have another old set of cabinets I thought about putting here, maybe put some really good casters on it to where you could keep it here. I’m also, wanted to be able to store like drum sander, other things that can go under it and then you can take those out and put them on this.
A dust mask or respirator will protect you while you're working, but won't do anything to protect you or your family from suspended particles still in the air. For this reason, an air filter is an absolute must if you work with woods indoors (I know of guys who sneezed out sawdust after working too long without an air cleaner). It's possible to make your own air cleaner out of box fans and furnace filters, but retail air cleaners will usually be much more compact. If you go that route, we recommend Wen 3410 3-Speed Remote-Controlled Air Filtration System for smaller shops.
The refrigeration setup in your van is an area where you really do get what you pay for, whether you’re paying in money or in time. The best options are the most expensive. The cheapest options are a pain and/or don’t work very well. And if you try to save money with a DIY refrigerator setup, you could end up spending a lot of time on installation.

Ultimate Small Shop

×