Most businesses must obtain a variety of business licenses, permits, and registrations before opening their doors to the public. As a small business owner, it is your responsibility to ensure that you are abiding all the laws and regulations applicable in your state and to your particular industry. You also have to research and apply for all relevant permits and licenses that apply to your business type and location. Remember, it is impossible to plead ignorance as a defense. It’s up to you to educate yourself. When in doubt leave it to the professionals. CT Corporation offers custom license packages that simplify the process for business owners. Click here for an example of what that looks like.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Every shop should have good lighting, whether natural or artificial. My video work dictates limited natural light, so I was sure to have plenty of overhead T8 fixtures (6500k). You’ll hear me mention in the video that I was disappointed to see that the ends of the shop were just a little dark. Thankfully, I was able to get the contractor to come back in and drop in 4 more fixtures for me, two at either end. Now the light is bright, crisp, and evenly distributed from one side of the shop to the other.
There are some variances in the features and reliability of different model years, and differences between the Mercedes Sprinter, Dodge Sprinter, Ford Transit, and Dodge Promaster - so make sure to do your research. The Sprinter RV Conversion Sourcebook is an incredible resource on all things Sprinter (and van conversions in general), and it goes over all the options in detail.
I will also typically secure those sorts of items under my locked platform if I am gone for a few days in the backcountry, because in reality I could probably care less if someone broke in and stole my box of food, versus someone who stole my clothes or expensive down jackets, which would be much more problematic (and costly) to replace on the road.
Now if don’t have space for a dedicated workbench say in your garage you can build one that folds out of the way when it’s not in use. Simply mount a board to the wall to hinge the table on, then you can use some eye hooks and chain to support it. Now it won’t support a ton of week but it should be just right for a weekend project every now and then.

Many retailers are also opting for digital signage. While digital signage and display solutions are more of an investment upfront, they allow you to quickly and easily show customers sales, new products, upcoming events, customer reviews, and more. Mira Digital Signage is a popular digital signage option for small businesses that is easy to use and offers affordable monthly payments. Click here for a free demo.

If you’ve got 220v, and want to get a seriously good TS, the Grizzly G1023RL is about the best bang for the buck in a 3hp industrial style cabinet saw…$1195/$1294 shipped. It’s not a necessity to have that much saw, but it’s close in price to many lesser saws, and is about all you’d ever need. If that’s more than you can stomach, and/or don’t have 220v, you’re limited to a TS that’ll run on a standard residential 110v outlet….again I’d look to a full size stationary saw. The typical contenders are the entry level price ranges are the Ridgid R4512, nearly identical Craftsman 21833, Steel City 35990, Porter Cable PCB270TS….all under $600. The next step up would include the Grizzly G0661, G0715P, Craftsman 22116 (by Steel City/Orion), Jet Proshop, General International, Rikon 10-201, and Powermatic offerings. These saws all have the potential to perform well…the end performance is largely dependent on how well you set them up, and what blade you choose.
I hope to build my own stand-alone dream shop sometime in 2015 – in the Texas Hill Country. I’ve not yet found the right lot, so much is yet unknown….but am thinking roughly 30′ x 40′ overall, with 10 or 12 foot ceiling. At one end, there will be a 10′ x 30′ space walled off into three spaces: a small finishing room, an office/design space, and a half bath.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern. 

A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.
Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on.  The rewards aren't usually good enough to compel me to purchase on their own.  But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.

If this all sounds too complex for you, there are alternatives. Thanks to advances in technology, there are tools available that help simplify bookkeeping and accounting so that you don’t have to hire a full-time accountant to take care of the basics. We’re big believers that a technology-led approach to running a small business will leave you with more actionable insights, more time to focus on your day-to-day operations, and ultimately, more money. For details on the cloud-based technologies that more and more businesses are relying on, make sure to check out our cloud-based business guide.
Spacious pathways are a key aspect of good store planning. In fact, it tops the list of retail experts’ store design tips. Heshy Lovi, Sales and Marketing Director for M Fried Fixtures, recommends aisle widths of four feet or more. This, he says, ensures your aisles and pathways will be comfortable for all customers, including those using strollers or wheelchairs.
It’s tempting to place new products, hot items, and sale signage front-and-center so they’re the first things customers see upon entering. But don’t do this! The first few feet inside the door, say five feet for a small store, and 15 feet for a larger store, is known as the decompression zone. Store design experts strongly advise against cluttering up this space.
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.
DeAnna says that in general, the front left of a retail store is a good location for the checkout counter, like the one above. Shoppers naturally drift to the right when they enter a store and tend to loop around the store, leaving on the left side. So, a checkout at the front left of your store puts it your customers’ natural exit path. Plus, it doesn’t distract them from shopping as they make their way around the store.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
There is a profound difference between a good idea and a thriving business, but as the saying goes: “A journey of a thousand miles begins with a single step.” At a certain point, turning your dreams into reality is as basic as putting a plan in place and, step by step, making it happen. The good news is that there has never been a better time for starting and learning how to run a small business.
We use this fan for extra circulation when it’s hot, and to get the air moving when it’s cold at night and we have all the windows closed. We also keep it on for our dogs while we’re driving. There are cheaper 12V fans out there, but generally the cheaper the fan the more power it draws. The Endless Breeze is a great little fan, and it’s definitely worth getting for the added ventilation.
I know in Missoula the garbage men do not like unbagged dust chips. They sent my friend a warning notice in the mail. Do you pull your drum out to the garbage and let the dust fly or dump it into a bag? My friend has garbage cans with 33 gallon liner which he pulls out of a sealed dust collection box beneath the cyclone… then he uses a hand truck to haul it out to the alley and then puts a fresh can in the box. It seems like a simple dust management method by not handling the dust by either scooping or dumping it out into a bag. I am always trying to think of ways to have less contact with harmful dust particles and I am curious as to how others handle the situation. Have a great weekend!
Have a walk-through yourself and see where the visual cues guide you or get your staff, friends, or family to do the same and give you honest feedback. Don't forget to observe your customers and see what they're drawn to, what they avoid, and how they move, then match that with your intended design. If you keep resilient and keep your eyes and ears open, you'll be sure to create a retail design that's a win-win for both you and your customers. 
You’ve probably considered what goods and services you’ll be offering, but have you researched the cost of sourcing your raw materials? How about the cost of turning those raw materials into your finished product? Do you understand how much you’ll need to charge for your products/services in order to cover the expenses of renting a space, paying employees, leasing equipment, and paying for permits and regulations? Moreover, have you considered if the answers to these questions will provide the kind of operating margin you’ll need to pay yourself a salary?
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
You may not have heard of Lemonade Freedom. It’s an organization set up after a spate of children’s lemonade stand closures by police who decided to take an absurdly heavy-handed approach to permit enforcement (you can read more about it in Forbes). Apparently the kids involved hadn’t applied for the necessary paperwork to run their stands. In one example in Georgia, three kids saving for a trip to their local water park had their endeavor closed down because they lacked the business license, peddler's permit, and food handler's license. Crazy? Only mostly.

I didn’t want to get a truck with a million miles on it. I am not a trucker by trade; I got my CDL specifically for this project. I didn’t want to get into a truck and then have to worry about its structure, engine, and transmission—and then start building Optimus on top of it. That’s why I got a brand-new truck custom-built from Western Star to become Optimus Prime.
The kind of apps that fall into this app type are extensive. Facebook, Instagram, Snapchat, Twitter, WhatsApp, Pinterest, and YouTube are all examples. Remember that some of these apps have been worked on for many, many years. Thus, a v1.0 social app or social networking app will likely not offer all of the same features. For instance, Snapchat did not start with videos, filters, or their "Stories" functionality. A social app would, however, include user authentication, friending, favoriting (or other data interaction), some sort of messaging, and comparable "baseline" functionality.
Now we’re using a lot of recycled materials in this project including some kitchen cabinets that were removed some a kitchen renovation project a few years ago and you know this is something that a lot of homeowners do if you’re real careful about removing the cabinets from a kitchen renovation or a bathroom renovation you can use them in a lot of ways around the house and certainly works good for a workshop like this.
The tablesaw—This tool is the backbone of nearly every shop, and for good reason. It allows unmatched precision in ripping parallel edges and crosscutting at a variety of angles. Most woodworkers find it crucial for the basic milling of stock. It is also suited to many joinery tasks, easily producing tenons, box joints, and—with a reground blade—the tails for dovetail joints.
With such an unstable job market and it being harder to get employed, more people are moving into entrepreneurship and being self-employed than ever before. Woodworking is a fantastic business opportunity, but you might feel that you don’t have the space or money to set up your own workshop and sell your goods. If that sounds like you, then you should check out Ultimate Small Shop by Ralph Chapman.
Plywood comes in several different types, the most common being pine and lauan. We used ¼” lauan plywood for the walls in our van. Lauan is cheap, it bends easily, and in our opinion its grain pattern looks nicer than pine. Hardwood plywood like birch costs more than pine or lauan, it weighs more, and it’s more difficult to bend. This type of plywood is a great option for furniture, but we think lauan is a better choice for your walls and ceiling.
Reflectix only works if there is an air gap next to it - Reflectix themselves recommend at least a ¾” gap between their material and the area to be insulated. This is the case because Reflectix is a radiant heat barrier, and when you put it right up against your van walls the foil cannot reflect back radiant heat (remember, radiant heat is only transmitted through air or a vacuum). If there is not an air gap, the insulating power of Reflectix is very low.
To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.
I have been working on building out the space, starting with a new welding table and small material/saw rack. I was able to dedicate a 20' x 28' area to fabrication. I need to figure out some things like angle grinder storage, fume exhaust hood and cold saw set up, but I will get there. Power is one nice thing with a 400A 208VAC 3ph supply panel. Also got the compressor in a sound dampened closet with cooling so the noise level is down significantly. Oh ya, dedicated 15 ton AC for the shop has been nice.
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
We have Eclipse Sunshades installed on our van. While they’re pricier than the cheap sunshades you’ll find at Walmart, they’re every effective. And since they permanently install on your windshield they’re much more compact - a big plus for living in a van. All we have to do is pull the shades across and velcro them together in the middle and we’re protected from both the sun’s rays and prying eyes.
Above all, remember that all of these elements can form part of your negotiation. Unless you are pursuing a highly desired space in a hot rental market, there is usually a point of leverage available to you in every lease negotiation. When it comes to getting the best possible deal in these situations, you’ll want to seek quality professional advice, this will normally include a broker and real estate lawyer.
You may already be aware of something known as the "butt-brush effect," coined by consumer behavior expert Paco Underhill. He discovered that a typical customer, especially women, will avoid going after merchandise in an aisle where they could potentially brush another customer's backside or have their backside brushed. This holds true even if the customer is very interested in a given product. An easy way to avoid this problem is to ensure that your aisle, floor, and displays allow customers to have more than adequate personal space when browsing your products.
Many retail fixture and display companies provide store planning and design services to their customers. Though typically not free, these in-house design services can be far less expensive than hiring an independent designer. Plus, they can help streamline the process of store layout and planning, along with the purchasing and installation of displays and fixtures.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.
Listing agents are hired by a landlord to list their commercial property. Listing agents earn a commission that’s paid by the landlord, typically between 3% – 6% of the total lease. Tenant brokers, on the other hand, represent tenant interests. However, tenant brokers also typically earn a percentage of the overall commission paid by the landlord, knows as the tenant broker’s fee.
As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.

It almost goes without saying that everything about your shop's design should project the right answers to each of these questions. But in today’s market, you have to go one step further. In our digitally connected world consumers have seen it all. The true art of compelling store design is in telling a story about your business, while simultaneously anticipating the needs of your customers. It’s all about the surprise and the delight.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.

Keep your air hose and fittings in one place and out of the way. Screw a coffee can onto a scrap piece of plywood. Attach a 2-1/2 in. riser block to the edge of the plywood and hang the entire contraption from a wall or work-bench. Drape your air hose over the coffee can, and store your fittings inside. It also works great for hanging extension cords. — Walter Barndt. Build an air compressor cart.
However, Sprinters are a lot more expensive than other options. It can be tough to find anything reasonably priced with less than 200,000 miles. For the Mercedes Sprinters, parts are more expensive and it may be difficult to find mechanics that have experience working on them (this is less of an issue with Transits and Promasters). And, since these are complex vehicles, they don’t lend quite as well to tinkering as something classic like a VW Vanagon or old Ford Econoline.
If you’ve spent time at your local flea or farmers’ market over the last few years, you may have noticed the explosion that has taken place in the number of innovative small business concepts. From cool new clothing lines to ingenious fusion foods, the sheer diversity of the ideas on display really hammers home one of the key lessons when starting a small business: You need to find your key differentiator. For some this is their brand story, for others it’s the value of their service, but for many quick service restaurants and small retailers, it’s a distinctive core product line that demands the attention and interest of your customers.

Now, we’ve already applied some resurfacer to fill up some of the deeper holes and after that dries overnight we’ll use a floor leveling compound tomorrow morning to really smooth everything out. Leveling compound is more fluid than the resurfacer so it flows into all of the low spots to even out the surface. Now, this won’t look like a finished floor when Tim’s done but it should do the job for our shop. Now, while he wraps up this Emily has a Best New Product that might be a great addition to your workshop.
Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
Firstly, more and more consumers are rebelling against the generic offerings of big-box retailers and seeking out the unique, personal touch offered by small, local business. You can leverage this message by weaving yourself into the fabric of your community. Canadian yoga apparel retailer Lululemon has enjoyed explosive growth thanks to their ability to do just this. According to their website, “A Lululemon store is so much more than a place to shop. It’s an education centre, a yoga studio and a meeting place. It’s a local hub for educators, ambassadors and guests to gather to learn, sweat and connect. It’s our lifeline to our communities and the soul of our company.” Lululemon uses free events to make people feel that they have a sense of ownership over the brand, and you can too! Getting people through your door is 90% of the battle and event marketing definitely can bring in crowds.
In a small store, these are usually one and the same. In stores where customers don’t shop with baskets, Lesley recommends having a checkout counter large enough to hold products as customers continue shopping. Remember, empty hands pick up more products, and that leads to more sales. Also, make sure checkout counters are large enough to handle the checkout process efficiently and allow space for customers to set down a handbag.
A dust mask or respirator will protect you while you're working, but won't do anything to protect you or your family from suspended particles still in the air. For this reason, an air filter is an absolute must if you work with woods indoors (I know of guys who sneezed out sawdust after working too long without an air cleaner). It's possible to make your own air cleaner out of box fans and furnace filters, but retail air cleaners will usually be much more compact. If you go that route, we recommend Wen 3410 3-Speed Remote-Controlled Air Filtration System for smaller shops.
Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.
Since your business name is often the first thing potential customers will see or hear, think of it as one of your key tools for leaving a lasting impression. The right name, like a firm handshake, can play a role in your brand’s perception. So make sure it’s strong, catchy, and unique, but most importantly sends the right message about your business.
Our Advice: Plan for aisle and display pathways of at least three feet, six inches wide, without obstructions. Then, once your fixtures and displays are in place, further test your store’s pathways by rolling a large baby stroller throughout your store. If you can easily navigate all traffic pathways, your customers should enjoy a comfortable browsing experience.
Tight control of inventory, while not a particularly glamorous part of owning a small business, is therefore one of the most important ways you can impact profitability. The good news now is that there is an array of technology available that can make this whole process much smoother, including sophisticated forecasting tools that will help you predict your required inventory levels for each day based on past sales, weather records, and many other factors.
My enthusiasm was kindled and I made friends with Surrey Timbers for more 'exotic' wood. My next purchases were a Drill Press and a Scroll Saw from Axminster Tools and I set to work. An excellent piece of Yew followed by some Thermal Ash has so far produced 4 cribbage boards. I then obtained a Palm Router which, after some practice, I find better for the more intricate work.
The first is that they will need to be powered by a product catalog. Many times that already exists and an app will just leverage APIs or web services to pull back products. If it doesn't, however, it will require either a custom buildout (beware!) or leveraging platforms like Shopify, Magento, or comparable solutions. The strength of these tools include providing the administration interface to add new inventory, APIs or SDKs, ways to store items in a cart, and similar features. The downsides are that you'll be limited by their workflow and customizations.
Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.
From building websites for other small businesses to providing technical support for certain projects, quality web development is in high demand right now. With such a technical skillset, make sure you can describe what you do and how you will do it in easy-to-understand language. Test your messaging on friends and family who don’t have a firm understanding of the work you do.
The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself). woodworking shop design
×