SBA provides support and tools to aspiring small business owners and in particular to minority-owned, women-owned, disadvantaged, and veteran-owned businesses, including a government-backed financing scheme to qualified participants. Local and state authorities also have a range of programs designed to encourage the growth of your small business. Make sure to research your local authority’s website.
Shop looks great Marc, I see the Clear Vue in the picture. I love mine, I used 8″ PVC for the main trunk line and came out of that with 6″ drops. It works great. I wound up building a collection bin instead of using a can, only thing I didn’t do was make the bin big enough. It holds more than the typical can but I still should have made it with more capacity. The 1800 with the 5 hp motor is stout.
Now that you have your goals mapped out and you know the exact tasks that will help you accomplish them, I want you to pick a day of the week (preferably Monday or Friday) and start planning the week ahead - don’t skip this step, never skip this step. Schedule which one these tasks will happen on what day of the week. So you are literally pulling the tasks from that spreadsheet and placing them into this weekly planner. It’s important to keep in mind deadlines (the ones you set for your goals and when they should be accomplished) and the amount of time it takes you to do a task. You may also want to write down which day it’s due, and who is responsible for this task (if you work with a team).
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience.
If you are looking to sell your business, it is important to engage a lawyer who is a business specialist to ensure you gain the best possible valuation. A small business is valued by assessing the potential ongoing income from the business over the coming few years. Normally this means that a business will be valued at three to five times net revenues, which can present a potential issue for particularly tax-savvy small business owners. Remember that every time you write off an expense against your business, you are lowering the net margin of the business. So, that dollar you saved by writing off the expense could cost you three to five dollars on the valuation of your business.
There you have it! Now you have no excuses, you must start planning right away. Please remember this can take a lot of time and a lot of work, so be sure not to stare at your task list in its entirety too often. I don’t want you to get overwhelmed knowing all the things you must get accomplished. Just focus on the goal that is the most important and attack it, task by task. Need help organizing these goals? Check out my Goal Planning Worksheets here:
I save all my back issues of The Family Handyman magazine and love the projects and repair tips. The trouble is, I’m not always ready to do the project when the issue arrives. To make my favorite articles easy to find at a later date, I put a stick-on label on the cover and then add notes for easy reference when the time comes to do the job. — Willie Schreiber. Plus: Check out this small workshop storage solution. Small woodshop workshop on a budget