In addition to sheer power, look for a model with a built-in thermostat so you can set it and forget it. This convenience feature is well worth it so you don’t have to stop what you’re doing mid-project to manually turn your heater on and off to maintain your desired temp. A good garage heater will mount to the wall or ceiling to save space and will come with a durable housing and full safety screen to keep dust and wood chips from reaching the heating elements and starting a fire.
In the case of this guide we’re going to use an area that’s a little larger and show you the tools you’ll need to set up a small workshop in just a 10×8′ shed. The list of tools is generally considered enough to cover the most common tasks. Everyone will have their own opinion on this and naturally it depends on the work you’re carrying out. But the tools on the list should be enough to strike a productive balance between having enough to get the job done and not being caught short so you’re having to borrow a friend’s. Invariably people grow their collection of tools as the jobs dictate. You don’t necessarily have to buy everything at once, just build up your list as you need to.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
If your shop will be attached to your house or another struc­ture, it will likely need to match its foundation, tying the two structures together so that one does not structurally stress the other if they shift differently. That may dictate a poured concrete or concrete block foundation. Regardless of your foundation type, a cold concrete floor will sap energy away from the rest of the structure if you are not careful, so think about how to insulate it well before you build.
Above all, remember that all of these elements can form part of your negotiation. Unless you are pursuing a highly desired space in a hot rental market, there is usually a point of leverage available to you in every lease negotiation. When it comes to getting the best possible deal in these situations, you’ll want to seek quality professional advice, this will normally include a broker and real estate lawyer.
If you have the available time, taking your DIY campervan for a test run (or two) is a great way to identify any problems while you still have access to tools, package deliveries, and a place to work. There’s just a lot that you can’t foresee until you live in your van. Taking it out for some short trips throughout your build will help you understand how you’ll actually use your new living space, what’s necessary, and what’s not.
In addition, if your aisles aren’t wide enough, you could be subject to complaints or lawsuits under the Americans with Disabilities Act (ADA). The ADA requires you to have aisles that are at minimum three feet wide. If you’re reported to be non-compliant, you could be fined if you don’t widen your aisles and remove obstructions. Learn more about the ADA’s retail store requirements here.
These basics are going to set you back about $180, leaving you with $320 left to work with.  We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives.  This should lead to more consistent results, more enjoyable builds, and increased efficiency.  These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.

Pegboard panels like this are extremely popular way to display and store hand tools. But they have one annoying problem is that when you lift off a tool, often the hook itself will pop out of the board. And that happens with over a number of times, every time you reach for a tool it can get pretty annoying. So you can buy at the hardware store, they make straps and special devices to hold the hook in place, but I’ve found this works just as well and it’s a lot cheaper.


A not for compensation nonexclusive arrangement, on the other hand, gives a tenant maximum flexibility. It’s nonbinding and there are no commissions negotiated. Instead, it gives the broker the right to speak on your behalf and schedule listings for you to see. However, while it provides flexibility, this arrangement gives the tenant broker less of a fiduciary duty.


Before starting your small business and opening its doors, it is important to take some time to define your end goal. While it almost goes without saying that this goal will be subject to change, it is only by recognizing and clearly articulating your long-term ambitions that you can provide yourself with a compass that will guide every business decision.
Remember the social media networks we asked you to secure in section five, Choosing a Business Name? Well, now is the perfect time to activate those channels. Use social media to build excitement about your grand opening and keep potential customers informed about special promotions and sales. People want to know what makes you special, so tell them why your store or restaurant will be different to what is currently available. From sharing pictures of that new fancy espresso machine or sneak peeks of your store’s interior, you can gain buy-in to your central message and build some anticipation before you even open your doors. Knowing how to to leverage key social channels is imperative to starting a success small business that will stand the test of time.
I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
Hi, I have looked through pictures of the shop books. What I am interested in finding is a book with layout design options. I am ready to build a new shop for myself and want to put dust and electrical under the slab. Best layout designs would help me to figure out how to layout a shop that is aprox. 28'x 36'. Is there a book that has this type of information.
As part of my antique restoration work I do a lot of faux finishing – hence the supply of stains and paints. Since I didn’t want to dust the house, the new shop is not connected to the house heat and air system. But, having just finished our first winter I now know the shop didn’t get below 45 degrees – and, the oven in the corner can make the shop toasty in no time at all.
In the case of this guide we’re going to use an area that’s a little larger and show you the tools you’ll need to set up a small workshop in just a 10×8′ shed. The list of tools is generally considered enough to cover the most common tasks. Everyone will have their own opinion on this and naturally it depends on the work you’re carrying out. But the tools on the list should be enough to strike a productive balance between having enough to get the job done and not being caught short so you’re having to borrow a friend’s. Invariably people grow their collection of tools as the jobs dictate. You don’t necessarily have to buy everything at once, just build up your list as you need to.
Without organization, living in a van can feel cluttered and chaotic, so you'll want to make the most of your storage space. This is a good time to make sure you've paired down your belongings to a reasonable amount and to make sure everything has a place. (As a former engineer who loves making things as efficient and optimized as possible, this was Ben's favorite step!) 

Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regula­tions, a larger lot, or more congenial neighbours. 


Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
I looked around at many versions of Taiwanese drill presses. I ended up purchasing the Ridgid DP15501 15" drill press because I liked the way the quill stop was made, the work light, key stor­age, and the easy access to the belt change system. This machine was also on sale when I needed it, so that made it a slam dunk. Choose the one that suits you, as they’re all very similar. The table is large enough, and the distance to the column is large enough to allow you to do most anything a small shop needs. 
While we think a battery isolator and a 200-watt solar kit provide more than enough power for most vanlifers, some people may want additional ways to generate electricity and charge up their batteries. Especially if you’re planning on running power-hungry electronics like TVs and air conditioners, adding a generator and/or shore power hookups will help you deal with the extra load.
I’m a 60 year young widow who just bought a bright yellow 2003 S10 step side with the intention of camping in it. But I discovered that finding a used S10 step side topper is harder than finding hen’s teeth!! Buying a new one wasn’t an option. Just found a black step side topper for a Ford Ranger. Isn’t a perfect fit but it works. And the colors compliment each other although color wasn’t my primary concern. I took two days to drive from the St. Louis area of MO to the Kansas City area to pick it up.

There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
This is about how I built my wood shop. We decided to move from our previous home for a variety of reasons. I saw the move as an opportunity to gain a bigger shop for my wood working hobby. The house we found had everything we wanted, except for a shop or even a garage. It did have a non functioning indoor pool. We thought this space would make a nice wood shop. I could just build a floor over the pool and have a shop. As we got further into the inspection process, it was looking as though fixing the structure over the pool was going to be expensive. It looked like we would have to put a bunch of money into a structure that was not really a wood shop and not a functioning pool either. It made more sense to take out the pool and structure, and then build a wood shop from the ground up. We started this project by regrading our side yard to gain access to the pool in the backyard. Once we had access, we took out the pool. We half filled the hole where the pool was with compacted gravel. I realized that if we sank the shop into the ground I could have the ceiling height I had always wanted in the shop and preserve the view from the house. The design of the shop is a box with a shed roof. The roof wraps down the east side of the structure. I like to think of it as a slightly open toolbox. The entire shop is laid out on a 24 inch grid. The windows and doors fall within this grid. I had a general contractor built the shell and then I built the windows and interior. The interior walls are comprised of a 34 inch concrete stem wall at the base. Above that is a 9 foot, plywood wall. In the space above the plywood wall and below the shed roof is poly carbonate panel to form a clerestory. The tool layout in the shop is divided into 4 areas: an area near the door for material storage and prep, a central area for general wood working, and two areas near the back of the shop, one for turning and one for metal working.
These basics are going to set you back about $180, leaving you with $320 left to work with.  We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives.  This should lead to more consistent results, more enjoyable builds, and increased efficiency.  These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
Now nobody reasonably expects you to actually hit that exact number in five years time, but the point here is accountability. A really great small business plan forces you to think through your goals, associate a dollar value with each, and articulate clearly how you will make them a reality. By declaring your projected revenue in month seven or your expenses in year five, you are giving yourself a benchmark for success.
Disclaimer: We spend hours researching and writing our articles and strive to provide accurate, up-to-date content. However, our research is meant to aid your own, and we are not acting as licensed professionals. We recommend that you consult with your own lawyer, accountant, or other licensed professional for relevant business decisions. Click here to see our full disclaimer.
×