With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Because workshops are rough and tumble places, the right fan for the job will have an industrial-strength motor and adjustable fan speeds. Easy-to-clean metal blades and a fully encased motor housing are also important features, especially if your shop tends to fill up with sawdust, wood chips and other fine debris. That extra layer of protection will help the fan motor last for years instead of being damaged by particulates.
This is a great project if you carefully consider your needs first. I left out the vise and tracks, but had no problem hand picking good 2x4 stock at the big box stores. I did use maple on the top sides in case I ever decided to add tracks, but it was not a budget buster by any means. The cabinet and drawers were a first for me and a great learning experience. I also added retractable casters so I can easily move the workbench around my shop. Love the workbench!
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
Hi Ryan: Nice job on the truck. I also have ’94 Toya 4×4 coffin sleep setup. Looking to change (access cab wanted) and may use some of your ideas. One thing I didn’t see you mention is ventilation. I am from the Mid-Atlantic region(DC/Maryland, you’re old stomping grounds) and ventilation at the New is important. My side windows have screens and I use an old mesh fly with a flexible pole for the rear tailgate area. It works really well. Kinda jerry rigged but is easy to put up and take down as well as pass through for nighttime truck exits. Not needed out west as much since bugs and humidity are lower but can’t live w/out it in these parts.

My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.


I hope to build my own stand-alone dream shop sometime in 2015 – in the Texas Hill Country. I’ve not yet found the right lot, so much is yet unknown….but am thinking roughly 30′ x 40′ overall, with 10 or 12 foot ceiling. At one end, there will be a 10′ x 30′ space walled off into three spaces: a small finishing room, an office/design space, and a half bath.

So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.


We do not recommend using Reflectix to insulate your walls or ceiling. Without an air gap, the R-value of Reflectix is about R-1. Even if you have the recommended ¾” air gap next to the Reflectix, the R-value per inch is less than R-3. There are much more efficient and cost-effective insulation materials out there for these purposes - you’ll be better off filling the space with rigid foam board.
A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.
I set an initial budget of $10,000 to build the shop – everything from studs and drywall to hand tools and machinery. The final number was over by $1,000, but I’m still very happy with the result. The shop is now my haven, with a good sound sys­tem and good lighting. Every time I go back into the shop, it is exactly the way I left it, because it is my shop!

There are many inexpensive alternatives lying around the house or at your local store you can use to create a Halloween theme that will impress all your friends.”One of the most popular party favors is a framed picture of the party guest taken at your kid’s party. He or she could be showing off a silly hat or party costume, performing an outrageous party game stunt, or wearing a face full of frosting and ice cream. Having party guests create their own make-and-take frame to display this memorable photo makes it an even greater treasure for the memory box. Start with a plain square of cardboard with an opening the size of your picture. When the decorating is done, Ultimate Small Shop Reviews simply glue the picture to the back of the frame. Why not turn that Cooking Interest, Comic Book Collecting, or Your Retro Clothing Collection Into A Home Based Business Venture! Most people enjoy hobbies they have pursued with great enthusiasm for years. Even though they may find their leisure activities fulfilling and enjoyable they never imagined making money with a fun hobby! Are you one of these gifted individuals? These talented individuals might have a passion for sewing fabulous original wardrobes, marvelous hand knitted items, furniture making, creative paintings, photographs, jewelry art, greeting card design, doll making, original toys, baby clothing, candle making, quilting, calligraphy, fancy soap making, about anything you can imagine! Crafting is actually a great way to start a home business on a shoestring. You might want to start on a small scale by offering your creative work to friends and family. Later on, once you have enough products, you might decide to rent a booth at local flea markets or crafts shows to display your work. As you may know, the Arts And Crafts Industry Is Enjoying An Amazingly Phenomenal Popularity. People are eager to purchase hand made clothing, furniture, custom made keepsakes or jewelry. If you have the creative talent this is one business you should consider! A friend, Joyce, diverted her obsession with candle making into a thriving business. She started by selling her hand made scented candles to friends and neighbors. Word of mouth spread about her candles. Soon she was receiving enough orders to keep her very busy. Joyce throws house parties to sell her candles and also takes custom orders from ads she runs in local newspapers. Next, she plans to take her candles to the stores and malls in her area.”Today is life – the only life you are sure of. Make the most of today. Get interested in something. Shake yourself awake. Develop a hobby. Let the winds of enthusiasm sweep through you. Live today with gusto.”Our hobbies help us to relax and forget our everyday problems and troubles. We are all experts in one or more fields of our lives. Ultimate Small Shop program But I am sure that not everyone has a hobby that makes money for him/her (except, of course, if you love your job).Just imagine, wouldn’t it be great if you could have money making hobby? You could get involved even more with what you already love to do, you could treat your family and friends with the extra cash, or… even quit your current job that you probably hate.
Shop layout is all about making the best use of space. Place your machines so that you have adequate “safe space” that you need to work around them. The “buffer area” beyond that is the amount of room you need to run large stock though a given machine, keeping in mind that buffer areas can overlap between machines. If you want to get more organized, buy some 1/4-inch squared paper, make scale models of each machine including the safe space around each, and place them on your model shop layout. Remember that buffer areas need to be long enough to put an 8' sheet through a table saw, or a 6' plank through your planer, for instance. I raised my planer, so that I can use the area above my router table to pass long planks through the planer – all it takes is some modelling, and a little shuffling, and you will find the layout that works for you. Each space will have chal­lenges; I had the area under the stairs that was wasted space, so I installed the dust collector there.
While strolling through the recent entries to our online shop gallery, I spotted some pretty novel designs as well as a couple of fun videos worth taking a look at. From brilliant solutions for tight spaces, to novel repurposing of department store display racks, there were plenty of interesting elements to the eight shops listed in my February round-up. By the way, if you’ve already seen our art director’s video tour of his redesigned garage shop (Mike’s Garage Shop), you can go ahead and skip it. If not however, it’s really worth a look!

This is a fundamental question. A good place to start is with a survey of your property. Most municipalities have a maximum percentage of your lot that you can build on and standard setbacks from your property lines that you will need to adhere to without needing to request special permission to build. On a photocopy of your survey you can draw in what your local setbacks are in order to define the location within which you will be permitted to build. In a best-case scenario, you will have the space to build without compromising too much on space or location; otherwise, you may need to request a minor variance, which would allow you to circumvent an obsta­cle such as a setback.
A loop floor plan, sometimes called a racetrack layout, creates the most guided shopping experience of the three. A loop store layout features a defined pathway throughout the store, which exposes customers to every item on display. Bed, Bath & Beyond stores are good examples of a loop floor plan. Loop floor plans work very well with zone merchandising tactics, too, which we discuss in detail below.
Hey there Ryan. Cool blog! I love the idea of trucking-it! I’m not able to do something like that, though I wish that I had taken the time when I was younger to do so. Here’s a suggestion that you might consider, if you haven’t already considered it before: Obtaining and using a hammock. I’d suggest bolting in an eye hook on the truck, or using the bumper as a tie point if you don’t have a second tree around. Also, in the high desert, you could use rocks as anchor points for it. Just an idea, from one camper to another.
A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.
You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.
Living on the road puts you in a wider variety of situations and environments than being stationary. If something goes wrong in the wilderness or if a disaster strikes, you’ll want to know what you should do. The SAS Survival Handbook is one of the best survival books out there. It covers primitive camping, edible plants, encountering wild animals - even disaster situations like nuclear war. It’s packed full of good-to-know actionable information. And it’s a blast to read.
What I have done in my man cave of a shop is to install above my finishing table a strip of track lighting where I have fixtures ranging from the typical bright white incandescent (typically around 4700k) all the way to the average halogen spot that I figure someone would use with an art piece (normally around 3700K). this allows me to point each light and view my piece and finish under varying light conditions to judge whether or not I prefer a particular finish or not. It also helps in photographing items (though filming is a whole nother story, I still have my 5400k T8 overheads for working).
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!
At a time when you’re focused on getting in front of customers as quickly and as often as possible, it can be hard to think about official requirements like registering a business name or deciding on a legal structure. Still, now that you have decided to start a small business or buy an existing one, one of the first critical steps is determining the business entity that's right for you.
If you are looking to sell your business, it is important to engage a lawyer who is a business specialist to ensure you gain the best possible valuation. A small business is valued by assessing the potential ongoing income from the business over the coming few years. Normally this means that a business will be valued at three to five times net revenues, which can present a potential issue for particularly tax-savvy small business owners. Remember that every time you write off an expense against your business, you are lowering the net margin of the business. So, that dollar you saved by writing off the expense could cost you three to five dollars on the valuation of your business.
GoWesty, a well-known Vanagon restorer and parts maker, recommends not buying a Westy unless you have at least $25,000 to spend overhauling it and replacing aging components. Even if you find a cheap Westy hiding out in a garage somewhere, be prepared for frequent breakdowns and expensive mechanical headaches unless you spend the cash to fully rebuild it.

Planning your store layout is no small task, but many small retail store owners do it all themselves with great success. So why not you? Take it slow, follow our seven steps, and remember to put the customer first. With the ideas in this guide and a little elbow grease, you’ll soon be on your way to mapping out a retail store that’s easy to navigate, welcoming to customers, and best of all—profitable.


Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
Other than that, you can’t have too much light — especially north light! — and you want accommodations for all the electricity you can imagine. Ceiling fans are a must. A good dust collection system is good, too. Don’t forget to plumb in for compressed air. Do NOT use hard PVC water pipe for compressed air — ever. If/when it breaks or ruptures, it explodes into tiny sharp glass-like shards. I know firsthand. I’ll tell you about it some other time. Think balloon popping!
The primary investment of any garage workshop are the tools. Protect your investment with a high quality tool chest that is neatly organized and (if needed) lockable. Look for smooth rolling ball-bearing drawers, and if you’re buying used, beware of rust and dirt that could corrode your tools. We recommend installing drawer mats to keep your tools from sliding around. They also give your tools a softer cushion to rest in.
BEST ANSWER: Hi, I probably can't help, depending on where you are in the process. If the bench in the photo looks like it's just what you need, you should download the plan. I think Rockler has several ready to assemble benches that look quite good. Example: Large Workbench (N2000) Item #: 31719... I. too, am retired and trying to decide whether to buy or build. I have a bench that looks good and works good, but just is too light for hand work. It all depends on what you expect to be using the bench for. There are some good books out there to help us decide. "The Workbench" by Lon Schleining" is excellent. Also, Christopher Schwarz has written several good books on the subject. Vince, good luck and have fun working wood.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
We first obtained legal permission from Hasbro [which originally developed the Transformer toy line back in the 1980s] to build it late in 2015. I also had to obtain my commercial driver’s license (CDL), so I spent a few months learning how to drive a truck while simultaneously spending the winter of 2015-16 working with Western Star to piece together on paper a vehicle that mirrored the Optimus Prime truck. Once the factory delivered the truck in April 2016, we got to work on the customization and fabrication right away. It was roadworthy again by October 2016. So the entire process from start to finish was about a year.
×