Solar Shower. For easy, inexpensive showering in wilderness locations, nothing beats a good solar shower. This is basically a bag of water that you leave out in the sun until it heats up, then hang it from a high place and shower using the attached nozzle. 5-gallon solar showers should get you about 5 minutes of good water flow. There are also pricier but more convenient pump-operated solar showers that you can buy.

If you want to run a business operated by yourself and more than one employee, you may run into zoning issues if your location is zoned for residential use only. It’s common for municipalities to allow and encourage home-based busi­nesses but there will likely be a maximum area that you will be permitted to add for business purposes. If you try to build a shop that will contribute noise and traffic (from employees or deliveries) to an urban neighbourhood, you run the risk of run­ning into opposition from neighbours concerned by the impact your shop will have. Your municipality will have planners with whom you should consult as you begin to define the possibili­ties that your property will allow.

Disclaimer: We spend hours researching and writing our articles and strive to provide accurate, up-to-date content. However, our research is meant to aid your own, and we are not acting as licensed professionals. We recommend that you consult with your own lawyer, accountant, or other licensed professional for relevant business decisions. Click here to see our full disclaimer.
You’ll also sometimes want to walk a property with a licensed contractor. This is because some commercial spaces require lease build outs, which are necessary additions or improvements to the space. Build outs can be fully or partially covered by the landlord. It’s important in this scenario that you get an accurate renovation estimate and negotiate a build out into your lease.
Simply get a one-inch drywall screw and drive it into the hole right beside the hook. You want to use a one inch screw because you don’t want to hit the wall behind it and you just drive the screw in until the head of it is tight against the hook, it’ll just act as a shim, and you’ll see once I get this all the way in, it lock the hook in place, and now when you take the tool on and off it won’t come off. The hook won’t pop out.

GoWesty, a well-known Vanagon restorer and parts maker, recommends not buying a Westy unless you have at least $25,000 to spend overhauling it and replacing aging components. Even if you find a cheap Westy hiding out in a garage somewhere, be prepared for frequent breakdowns and expensive mechanical headaches unless you spend the cash to fully rebuild it.

A very simple countertop but one that should work great for our workshop, now we’ve already applied one coat of polyurethane to kind of seal up the plywood. Now we’ll be applying another coat once that dries to give it a little bit of durability because this thing will get a lot of abuse. Now Tim’s applying the same kind of clear sealer to our little rolling workbenches here, and I think this is a great idea, we’ll be able to roll these out, lock down the casters on the bottom then you can have a drill press or any other bench top tool that you can work on, then when you’re finished with them you can roll it right back, tuck them up against this wall and it serves as a good storage unit and gives you the chance to keep the workshop wide open for some of the larger projects we might be working on.


Using six pipe cleaners, you can make your own skeleton. Bend one pipe cleaner into two for the backbone. Twist another around the bottom of the backbone to make into the legs. Do the same for the arms. Join two pipe cleaners and twist them around the backbone leaving some space forming a ribcage. Ultimate Small Shop Woodworking Twist the last pipe cleaner for a head and glue on some eyes. Hang with a rubber band for a bouncing effect. Your kids will love making Halloween crafts with pipe cleaners. But be careful when cutting and keep them out of their mouth. Going trick or treating? Why not make a special jug to collect candies? Cut off the top two inches of a gallon milk jug. Soak to remove any labels. Paint orange. Once dry, paint or stick on eyes nose and mouth resembling a Jack O’Lantern. Use fluorescent paint for a nice effect. The jug can be kept for future reuse. Using glue and food coloring, you can make a see-through painting. Paint a Halloween image onto a piece of plastic wrap. Before the mixture dries, put another piece of plastic wrap on. Cut it out and hang it in front of a light source for a see-through effect. You could also frame the plastic pictures using wood or cardboard if you want them to be longer lasting. Make some hand printed spiders. Ralph Chapman Ultimate Small Shop Apply black paint to your palm and 4 fingers leaving out the thumb. Place palm onto a piece of paper. Turn the paper 180 degrees and print again making sure the palm overlaps. Add some wiggly eyes using either paint or sticks. This is suitable for even 2 or 3-year-olds. Make your own blood. It is less expensive than buying ready-made blood from the Halloween shops. It’s not difficult; all you need is Karo syrup and food coloring. While you’re at it, why not make some slime using glue, water, and borax powder. This is an advanced Halloween craft, so take your time and be careful. Using apples, you can make dried, shrunken heads. Peel the apples and coat with a mixture of lemon juice and salt to prevent browning. Carve out a face of eyes, nose, and mouth. Do not worry about the finer details as they will probably be lost when the apple dries. You can use whole cloves for the eyes and rice grains for the teeth. Let the apples sit out in a warm place for about 2 weeks. If you don’t have 2 weeks, you can speed up the drying by putting them into an oven on the lowest temperature for about 45 minutes and then dry out naturally for the next 2 days or so. Ultimate Small Garage Clock Shop Once dried, they shrink and deform into weird and scary looking faces. Says Angie Maroevich, “You don’t have to spend a fortune on commercial Halloween supplies to have a great party.
Every aspect of your store should flow from a clear statement of who you are and what you stand for as a business. From the sign hanging proudly outside your store window, to the color of the wallpaper in the in-store restroom, every detail should contribute to conveying your unique purpose and brand to the world. This consistency should also be applied to all your online assets, for example, your website design.

As the old saying goes, the only two inevitable things in life are death and taxes. Almost all small businesses in the United States are subject to some form of corporate income or gross receipts tax on a state level — that is, unless you happen to be a lucky inhabitant of the great states of Wyoming, Nevada or South Dakota. Actually, even these states will require you to pay state workers' compensation insurance and unemployment insurance taxes. Oh, and of course every small business in the country is subject to some form of federal taxation.


Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
If you’ve got 220v, and want to get a seriously good TS, the Grizzly G1023RL is about the best bang for the buck in a 3hp industrial style cabinet saw…$1195/$1294 shipped. It’s not a necessity to have that much saw, but it’s close in price to many lesser saws, and is about all you’d ever need. If that’s more than you can stomach, and/or don’t have 220v, you’re limited to a TS that’ll run on a standard residential 110v outlet….again I’d look to a full size stationary saw. The typical contenders are the entry level price ranges are the Ridgid R4512, nearly identical Craftsman 21833, Steel City 35990, Porter Cable PCB270TS….all under $600. The next step up would include the Grizzly G0661, G0715P, Craftsman 22116 (by Steel City/Orion), Jet Proshop, General International, Rikon 10-201, and Powermatic offerings. These saws all have the potential to perform well…the end performance is largely dependent on how well you set them up, and what blade you choose.
As always, great article! While my dirtbag adventure will likely only be about 6-7 months, I am starting to wonder about logistics. You mention that most people use the automobile they have. I drive a Prius. Not ideal for sleeping in, but I’m a pretty content ground dweller. I know that long-term I may start to question this. Here’s the proposition I’m considering: by saving on gas (45-50 mpg), I can occasionally cough up the money for lodging when I feel the need for added comfort. I can definitely do the number crunching, but I’m wondering if you’ve encountered people doing this or did similar analyses of your own at any point. I’d love to hear any insights you may have on this. 

I didn’t want to get a truck with a million miles on it. I am not a trucker by trade; I got my CDL specifically for this project. I didn’t want to get into a truck and then have to worry about its structure, engine, and transmission—and then start building Optimus on top of it. That’s why I got a brand-new truck custom-built from Western Star to become Optimus Prime.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Whether you build or buy your workbench, it must be designed and constructed to withstand the rigors and pounding you’ll put it through. The base and legs should be sturdy and the table should not easily be knocked over. The top should be durable and not easily dinged or dented. Make sure your workbench is made of a material appropriate for your types of projects, too.
Once again I would like to Thank You for letting so many of us see what is going on in your world. It is very educational and entertaining to see what has happened in the past few months of your dream shop build. As I was watching the video I periodically looked out my window to see the snow falling steadily and building up along the windowsill. Every now and then I imagined I was in your sunny backyard admiring your Shop. I am looking forward to seeing what you will create in your New Space. Keep up the Good work and Congratulations on your Dream Shop.
I’ve been living out of my Mazda 3—not the hatchback version!— for over two years now. I love the gas savings (standard transmission; I can get up to 40mpg) and the ease of getting around places. I don’t love that I can’t lay flat (hurts the back) and that organization is tricky. However, there are certainly ways to make it work. Ryan linked to one article and there are two others that shed light on some important aspects when going on a long road trip like this.
In a woodworking shop, lumber storage is key, and it’s best to design shelves or racks that are about 50 percent larger than you think you need — you’ll almost certainly acquire more materials as the years go on. To maximize a small space, use walls by mounting shelves to the ceiling and purchasing a sturdy step ladder to help you reach things. A wall covered in standard pegboard and outfitted with hooks allows you to customize hand tool storage and keep your most-used hardware within easy reach.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
A great product line will also reflect a range of price points. For a business that is working hard to convey a sophisticated and elite vibe, it might be a useful strategy to set a high minimum price, but for the vast majority of small businesses, your pricing should be guided by one key thought: I want every single person who comes through my door to be able to find something that fits their budget.

Store design experts agree that this area should be open, inviting, and free of overpowering displays and signage clutter, as shown in the image above. Many customer behavior studies, including those conducted by Envirosell’s Paco Underhill, support this opinion. They show that customers tend to ignore displays, signage, and even manned sales counters placed close to store entrances.


In today’s competitive business landscape, the key card that small business owners hold up their sleeve is their ability to offer something distinctive, original, and personal. As small businesses grow, however, it can become increasingly difficult for the time-pressed, financially strapped entrepreneur to maintain direct oversight over every aspect of their store.
Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
There are a number of woodworking fixtures you can get by without for a long while, but a sturdy workbench isn't one of them. The trouble is, those solid-hardwood benches we all lust after can completely blow a modest woodworking budget. Here's a bench that splits the difference. You'll get a top that can stand up to significant abuse, a sturdy, heavy base that keeps the bench planted where you put it, and an end vise and T-track system for holding workpieces as well as a variety of unique jigs. It may not look quite like a European bench, but it works just as hard as one for a lot less money.

If you want to spend as little as possible on a vent fan, the Fan-Tastic Vent 1200 (about $130) is your best bet. This fan has three speeds and manual controls, and it has the same quiet operation and energy efficiency of Fan-Tastic’s other fans. If you find that you need to use it while it’s raining, it’s easy to add on an Ultra-Beeze Vent Cover later on.

If you are going to apply for a trademark, make sure to conduct a comprehensive search, like the one mentioned in ‘Securing Your Business Name’ to ensure no one is already using your proposed name in a similar capacity. The United States Patent and Trademark Office also provide a simple search tool that will quickly let you know if you’re potentially infringing on someone else’s turf from a legal point of view.
Now I want you to create a spreadsheet or use my worksheets and write one major goal on the top. This can be the first goal you want to accomplish. Then I want you to list all the tasks you need to do (or someone on your team has to do) in order to accomplish this task. For example; let’s go going back to the goal of "Launching a New Website". The tasks you will need to do to get this goal accomplished are the following;

However, another critical component to small business success is being self aware. With a variety of tools at your fingertips, tracking basic accounting can be fairly simple. Still, in order to be strategic about how you spend your money, properly leveraging these tools will still require a little bit of legwork. What used to take you eight hours might now only take one hour. But if you’re not willing or able to run through your financial tasks on a regular basis, bringing in a bookkeeper or accountant might be your best option.
I am a firm believer in having your business goals align with your personal goals. In order to do that, you need to know what your personal goals are. This may be different for everyone, but I want you to be 100% honest here. I am writing this as an update in 2018 to this original blog post and I want to be honest and share with you my personal goals for 2018:
1. My vehicle is a Ford F-150, which is not great for off-road travel but is by far the best I’ve ever had for mobile living. The 6.5-foot bed is perfect for my 6+ foot height, and I can probably haul everything I own other than my home furniture in the back of it. How long is the bed of your Toyota? I’ve always assumed a small pickup would tight length-wise for comfortable sleeping.
We first obtained legal permission from Hasbro [which originally developed the Transformer toy line back in the 1980s] to build it late in 2015. I also had to obtain my commercial driver’s license (CDL), so I spent a few months learning how to drive a truck while simultaneously spending the winter of 2015-16 working with Western Star to piece together on paper a vehicle that mirrored the Optimus Prime truck. Once the factory delivered the truck in April 2016, we got to work on the customization and fabrication right away. It was roadworthy again by October 2016. So the entire process from start to finish was about a year.
Often times those same freedom-seeking, passion-driven individuals that started their journey filled with courage and optimism, become some of the most time-pressed and financially-stressed people out there. The flip side of getting to create your own wealth is that you are solely responsible for creating your own wealth. That’s right, it all comes down to Y-O-U.
We've written about routers on the site before and my favorite is the Bosch 1617​.  It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table.  On top of that, it comes with a plunge base which makes it significantly easier to use handheld.  The package clocks in at ~$190.

At some point in the process of starting a small business, it’s pretty much guaranteed that you will hear the following statistics (or variations thereof): 25% of new small businesses close their doors within the first year and 60% are gone within three years. The exact numbers here may vary, but the message is all the same: be afraid, be very afraid!

I used to coat my metal table saw and planer bed with auto wax because it makes the wood slide nicely across the metal. But then I saw an expert cabinetmaker use wax paper, and now I do the same. I keep a roll in my shop drawer and rub a sheet of it over the metal beds on my table saw, router, planer and disc sander. The wax coating doesn’t last as long as a good paste wax, but boy, is it a lot easier and quicker. — R.J. Hayes. Plus: 22 clever new uses for your tools.
I have a basement shop with a walk out and a seperate entrace to my shop.I have approx. 5oo sq feet to work in there, there is natural light that comes in with a graet view of the lake that we live on.I have started to dress up my shop after making such beautiful furnisher for other people it started with a bench witch is 11 ft, long and plenty of stoarage space under the bench , the low storage aera of the bench is made from black walnut and the bench top is oak with bubinga trim. Saw cabient is white oak ,miter saw cabient is walnut ,american chestnut ,cherry and maple. Now the joint cabient looks out of place so I will be making a better looking cabient for the 6in. jointer. I had made a plant self to start plants along the widows but took it out and put a bench top there so it looks as a big window sill but I use it for a place to set tools as I am working on the bench also I have put walnut around the widows and painted the walls.There is a 10in. powermatic table saw,powermatic drill press fl.modle,rockler 6in. jionter, mekeita compond saw,delta 14in band saw, I have two planers and a table mount router in my bench top ,also there is an old american lath witch I have in stoage and a sears jig saw.
Ok Rob let me try again .I would suggest you sign up for a community collage woodworking class or a woodworking coop where you can use the tools you will need to build the kind of items you have in mind. You say you have used the tools you listed but that could mean only used them once or twice. If you have minimal experience with tools and woodworking that might be another reason to take a class assuming there is one available . Do you have a space you can use as a shop ,a garage,carport etc? As far as tools and equipment are concerned I think Knotscott covered it very well. I know your supposed’s said you couldn’t find tools on Craigslist or garage sales but those might be the place you can make an offer on a shop full of tools in the price range you trying to stay in possibly with some materials and other extras. It might even work to put a wanted wood shop full of tools in the tools section of your local Craigslist.
Starting to see a trend here? Notice how each of these questions begins with the customer in mind. As with all things related to your store, it’s critical to put your customer at the core of your decision making. At first glance, little things like cold drinks that aren’t quite cold enough, can seem insignificant, but it’s often the little things that hurt the customer experience and can turn a customer off to your business forever.
If you dream of devoting your life to a cause you believe in, it might be time to start a nonprofit. You’ll need to incorporate your business and file for 501(c)(3) tax-exempt status -- and then you’ll be required to meet ongoing standards of compliance, but the payoff is making a meaningful impact on a cause you believe in. Want to do good while still making a profit? Consider social entrepreneurship.
Most businesses must obtain a variety of business licenses, permits, and registrations before opening their doors to the public. As a small business owner, it is your responsibility to ensure that you are abiding all the laws and regulations applicable in your state and to your particular industry. You also have to research and apply for all relevant permits and licenses that apply to your business type and location. Remember, it is impossible to plead ignorance as a defense. It’s up to you to educate yourself. When in doubt leave it to the professionals. CT Corporation offers custom license packages that simplify the process for business owners. Click here for an example of what that looks like.
I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino

To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
We love natural light as much as anyone, and the big windows in our van were something we were super excited about. But when you're living in a van, you'll want some privacy. Trust me. You'll also need curtains to keep out the lights when you're trying to sleep. Making your own curtains can seem like a daunting task, but it's not all that hard. (I speak as someone who had to look up a tutorial to operate a sewing machine!)
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
Many retailers are also opting for digital signage. While digital signage and display solutions are more of an investment upfront, they allow you to quickly and easily show customers sales, new products, upcoming events, customer reviews, and more. Mira Digital Signage is a popular digital signage option for small businesses that is easy to use and offers affordable monthly payments. Click here for a free demo.
I save all my back issues of The Family Handyman magazine and love the projects and repair tips. The trouble is, I’m not always ready to do the project when the issue arrives. To make my favorite articles easy to find at a later date, I put a stick-on label on the cover and then add notes for easy reference when the time comes to do the job. — Willie Schreiber. Plus: Check out this small workshop storage solution. Small woodshop workshop on a budget
×