We have Eclipse Sunshades installed on our van. While they’re pricier than the cheap sunshades you’ll find at Walmart, they’re every effective. And since they permanently install on your windshield they’re much more compact - a big plus for living in a van. All we have to do is pull the shades across and velcro them together in the middle and we’re protected from both the sun’s rays and prying eyes.

Of all the LED lighting options, puck lights are the most difficult to install. You’ll have to run wiring behind the ceiling/walls for each light. And you’ll need to cut a hole with a hole saw to recess the lights into the ceiling. But with some preparation and care it's not too difficult. We have full instructions for installing LED puck lights in our epic electrical post.
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
Keep your air hose and fittings in one place and out of the way. Screw a coffee can onto a scrap piece of plywood. Attach a 2-1/2 in. riser block to the edge of the plywood and hang the entire contraption from a wall or work-bench. Drape your air hose over the coffee can, and store your fittings inside. It also works great for hanging extension cords. — Walter Barndt. Build an air compressor cart.
Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.
Tired of holding a flashlight between your teeth while working in the dark? Make a light stand by bending a 2-ft. section of 12- or 14-gauge electrical cable into a U shape. Duct-tape the light to the ends of the cable. The wire can be shaped into a hands-free supporting base for the flashlight or bent into a hook for hanging. — Paul and Haylee Lytle. Check out another hands-free light hack.
By setting up a separate legal entity, you limit the financial fallout from a failed business, you shield yourself from legal risks (such as someone injuring themselves in your store), and you potentially put yourself in a more advantageous tax situation. Equally, if you are working with partners, ensuring you are set up with the appropriate partnership will give all parties reassurance about their legal standing, obligations to, and expectations from the business in question.
Can you outfit your shop with all the necessary hand tools for just $100? Christopher Schwarz says you can, and he’ll show you how to do it in this article. Take Christopher’s shopping list to the flea market and come back with everything you need for less than you’d spend on one new hand plane. You can do all your woodworking with hand tools, and this article from Popular Woodworking will equip you with everything you need.
Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.
Once again I would like to Thank You for letting so many of us see what is going on in your world. It is very educational and entertaining to see what has happened in the past few months of your dream shop build. As I was watching the video I periodically looked out my window to see the snow falling steadily and building up along the windowsill. Every now and then I imagined I was in your sunny backyard admiring your Shop. I am looking forward to seeing what you will create in your New Space. Keep up the Good work and Congratulations on your Dream Shop.
Depending on your situation, you may need to upgrade to 200 amp electrical service in order to meet the needs of your house and your shop. It may also be in your interests to add in a separate electrical service meter on your shop so that you can clearly write off electrical use for your business, or in future rent the space out and clearly separate out the utilities for bill­ing your tenant. Generally, you don’t want to skimp on the power to your shop or on the lighting you include.
After years of digging through piles of stuff on my workbench for the air compressor accessory I needed, I had this idea. I simply drilled 7/16- in. holes on the underside of my workbench top and threaded in a few 1/4-in. NPT male couplings with quick-connect couplers. A wrench and some upward pressure are all it took to screw the couplings into the wood. Now I just snap my accessories onto the couplers when I’m not using them. — Donnie Dressler. These are the best tools for automotive work.
We have a 5-gallon clear plastic Hedpak container that our sink drains straight down into. We really like this container because it’s clear, which means we can easily see how full it is. With 5 gallons of gray water capacity, we only need to empty it every 3-4 days. Dumping is easy - just remove the tank from under the sink and pour it out into an RV dump facility or other approved area.
×