What about when you’re camping? Well, most campgrounds (including many free National Forest and BLM campgrounds) have some sort of bathroom situation. If there’s not an actual running water bathroom, you’ll typically find pit toilets (aka vault toilets), which are basically much nicer/cleaner permanent porta-potties. We also recommend picking up a good poop shovel for those times you’re camping in a wilderness area without bathrooms.
These basics are going to set you back about $180, leaving you with $320 left to work with.  We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives.  This should lead to more consistent results, more enjoyable builds, and increased efficiency.  These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000. 

In my opinion, the best shop space is a flexible one. I know many folks expected that after setting up my shop so many times, I would be able to design the PERFECT shop space including a finishing room, a dust collection closet, and even some internal walls. But the truth is, the most important lesson I learned over the years was to expect change. My shop is not a static entity. It is more like a living breathing creature that adapts, evolves, grows, shrinks, and changes configuration. Committing to an internal spacial arrangement too early could yield disappointing results. This is why you won’t see me placing dust collection ductwork in the floor. I need to work in a space for at least a few months before I can be confident in my initial setup. Even then, I fully expect things to change at some point. If I made too many restrictive and/or permanent decisions ahead of time, these changes could be difficult or impossible to implement. So my best piece of advice is to forget about the concept of perfection. Instead, focus on flexibility. The ideal shop, in my mind, is little more than 4 walls, a roof, and a butt-load of outlets and lights. So here are some of my basic general goals for my new shop space.

The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code con­ventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow founda­tion may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the con­crete slab will structurally bear the weight of the shop structure you build above it.

“If it’s a retail space then location is critical. Proximity to other retailers, access to transportation, and visibility/signage opportunity can be critical. In this case, there may only be 4 or 5 spaces available that meet the business’s criteria and objectives. A good broker will sometimes develop creative alternatives that might be outside the locational parameters but offer other advantages – such as co-tenancy or lease term flexibility.


You can see I broke the ultimate goal down into smaller tasks. Now you just need to do this for all the big goals that you have mapped out for the year. You may have more ideas or goals throughout the year and that’s okay. With this type of document, you are able to add another category and tasks anytime you want. This is just the best way to keep track of all the little things you need to do to accomplish your goals so you never are stuck wondering what you have to do next.
Well, all these years we’ve always planned on this being a nice little workshop, and now’s the time that we’re about to remove all of this and create a nice realistic, practical workshop. Not a TV workshop that just looks good, but one that will be perfect for us to use for some of the projects we have on the show, and again it will be used by our construction company for some of the projects they have.
In all you can spend under $1,000 and be setup in a great workshop. But I know how it feels when you’re shopping for new tools… and you think… “why not buy the top of the line so it lasts longer”… or “may as well get the best while I’m spending money”… those kinds of thoughts won’t only get you into big trouble with your other half… it’s also COMPLETELY wrong.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 

In each case, we shuffled the bench, jointer, table saw, and band saw across to the top of the stairs, and then tied a rope around each to act as a safety while sliding the machines down the strapping on the stairs. Yeah, the table saw hit the wall, and the promise of a good mud and paint job saved my bacon. The rope worked well, and we were able to get everything down the stairs nice and slowly with­out any major issues.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
Expanded polystyrene (EPS) is an open-celled foam board (think styrofoam) that is the cheapest of all the foam boards. It does work, but we generally don’t recommend using EPS in your van. It insulates less than XPS (R-4 per inch), and the gaps between the foam cells allow moisture to penetrate, which degrades the insulation over time. Polyiso and XPS are much better choices for a slightly higher cost.
Other than that, you can’t have too much light — especially north light! — and you want accommodations for all the electricity you can imagine. Ceiling fans are a must. A good dust collection system is good, too. Don’t forget to plumb in for compressed air. Do NOT use hard PVC water pipe for compressed air — ever. If/when it breaks or ruptures, it explodes into tiny sharp glass-like shards. I know firsthand. I’ll tell you about it some other time. Think balloon popping!
We're living in an age where we can order groceries, turn on the lights in our house, or get in a workout from the convenience of our phones, tablets, or other devices. Apps are a part of our everyday lives. They are increasingly giving us more free time or vying for more of our attention, depending on how we choose to use them. With that, here are some of the more important changes since we published our app cost article in 2015.
Finally, think about the overall color and feel of your workshop. A fresh coat of bright white paint will help your lighting go farther, but you might also consider adding a splash of color for fun. An accent wall or an epoxy floor coating are good ways to upgrade your workshop from drab to fab without adding fussy decorations that will get in the way of business.

We first obtained legal permission from Hasbro [which originally developed the Transformer toy line back in the 1980s] to build it late in 2015. I also had to obtain my commercial driver’s license (CDL), so I spent a few months learning how to drive a truck while simultaneously spending the winter of 2015-16 working with Western Star to piece together on paper a vehicle that mirrored the Optimus Prime truck. Once the factory delivered the truck in April 2016, we got to work on the customization and fabrication right away. It was roadworthy again by October 2016. So the entire process from start to finish was about a year.
A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information.
Workers’ compensation insurance is designed to provide wage replacement and medical and death benefits to employees who are injured or worse on the job. In exchange for these benefits, the employee gives up his or her rights to sue for liability leading to the accident. Your premium will reflect the type of business you operate and the average salary of your employees. Much like auto insurance, business owners who are new to starting a small business or those with less experience tend to pay higher premiums.

To make the most of your workshop oasis, look for a water dispenser that offers a choice between chilled and hot water. This will let you enjoy a cold, refreshing drink in the heat of summer rather than a lukewarm bottle that’s been sitting around gathering dust. You’ll also cut down on the amount of plastic your household goes through, which is a boon for the environment. In the winter, the hot water tap will also you to make a cup of tea or a mug of instant coffee on the spot. No matter what your taste, a versatile drink dispenser will keep you hydrated and happy while you work.
As the old saying goes, the only two inevitable things in life are death and taxes. Almost all small businesses in the United States are subject to some form of corporate income or gross receipts tax on a state level — that is, unless you happen to be a lucky inhabitant of the great states of Wyoming, Nevada or South Dakota. Actually, even these states will require you to pay state workers' compensation insurance and unemployment insurance taxes. Oh, and of course every small business in the country is subject to some form of federal taxation.
Now that you have written everything out, now take out a calendar that has 12-month blocks and map out each business goal in the corresponding month that it has to be completed by (or accomplished). So you have 12 squares (12 months) and you are literally placing these ideas into the month you want to accomplish them by. By the time you are done with this, you will have a sheet of paper with all your ideas written into the months on the calendar.
Great website! I spent a summer living out of a ford focus hatchback while road tripping around the United States. The rear seats were replaced with a small platform to store gear and the rear windows were tinted. I enjoyed the freedom that anywhere I parked no one would see me hop from the drivers seat to my platform for some zzz’s. Also no one would guess that someone is sleeping in a 3dr ford focus.
SBA provides support and tools to aspiring small business owners and in particular to minority-owned, women-owned, disadvantaged, and veteran-owned businesses, including a government-backed financing scheme to qualified participants. Local and state authorities also have a range of programs designed to encourage the growth of your small business. Make sure to research your local authority’s website.

Assume that there aren’t any decent tools on craigslist or at garage sales, and keep in mind that I have absolutely no tools, dust collection, shop-vac, clamps, sanding & painting accessories, tables, materials to build my own tables/stands/jigs, or anything else—not even safety gear (you’re such a good buddy that you even let me borrow your extra set of goggles and your earmuffs when I used to come over).
We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.
×