Use this model whether you’re looking to turn your team of one into a two-person shop or you’re hoping to build out your marketing department to a team of 10 or more.  By focusing on the skill sets your business needs to be successful — rather than on the resume of an individual candidate — you’ll ensure vital functions are covered while expanding in a sustainable way.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
But now is the time to take a step back and go on some test runs in your van. Take it out for a weekend here or there (or better yet, a week or more). Try living in it as you expect to on the road. We guarantee there will be things that worked well in your head but not so much in reality. And you’ll come up with random little hacks and innovations that will make your life on the road easier and more enjoyable.
You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.
Tim Inman: You don’t say where you will be located, but if you are anywhere that gets cold I definitely have a suggestion. I’ve built three shop buildings over my years. In each one, I’ve put down 2-inch closed cell foam board underneath six inches of concrete for the floor. I would never build a shop — or anything else, for that matter — without this. The foam lets the concrete become a huge heat sink and warming stone. My feet are never ever cold when I work on this combination. The shop stays reasonably warm without spikes in the heat and cooling. The tools are more rust-free, and I like it.
Most workshop tasks require good ventilation, and that’s something garages are generally poor at. Plus, passive ventilation (like opening a window) usually isn’t enough. A ceiling exhaust fan is a good start but if you are serious about keeping things clean then your ultimate workshop should also include a dust collection system, central vacuum and air ventilation system. All three of these systems will keep the dust, dirt, and other heavy particles off your clothes and out of your lungs which makes for a safer work environment.
In today’s competitive business landscape, the key card that small business owners hold up their sleeve is their ability to offer something distinctive, original, and personal. As small businesses grow, however, it can become increasingly difficult for the time-pressed, financially strapped entrepreneur to maintain direct oversight over every aspect of their store.

Hey Marc. Just wanted to send a huge congrats your way for this milestone. It’s been pretty awesome to follow you on this journey since I discovered you on iTunes some 5 or 6 years ago. Mad props for what you’ve done to grow and enhance the online woodworking community as well as woodworking as a whole. I think with todays generation (as well as future generations) growing up behind a computer, the work that you and the rest of the podcasting world do will go a long way towards bringing new people into the craft. I hope that in the future you are able to start a series of videos showing how you introduce Mateao to the craft. Keep up the awesome work!
I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.
They say nobody ever started a small business out of a love for numbers, but if you really want to stay the course, you’re going to want to fall in love fast. It’s only by keeping detailed accounts and tracking your business’ numbers over time, (net sales, cost of goods sold, and average transaction size) that you’ll start to gather the actionable insights you need to make intelligent business decisions.

Woodwork in all its forms is an enormously popular hobby amongst enthusiasts of all ages. Most people, regardless of their abilities, just like to tinker with a bit of wood and make something. Starting out should be easy but the misconception can be that you need a fair amount of space to begin. The fact is that many people create versatile workshops in the smallest of spaces. One in particular we like is Stephen’s 8×6 Workshop as he manages to cram an army of tools into a tiny area in a systematic and neat way.


To avoid buyer’s block, define the core characteristics you absolutely need in your business. Write them down in a prioritized list ranked from ‘deal breaker’ to ‘would be nice to have.’ Now cross off the bottom five and focus only on the ones that are left. Compromising is essential in choosing a commercial space, especially in popular neighborhoods. Besides, you’d be surprised how what once seemed like a less than stellar storefront can become your dream location once you get those creative juices flowing.
I’m a 60 year young widow who just bought a bright yellow 2003 S10 step side with the intention of camping in it. But I discovered that finding a used S10 step side topper is harder than finding hen’s teeth!! Buying a new one wasn’t an option. Just found a black step side topper for a Ford Ranger. Isn’t a perfect fit but it works. And the colors compliment each other although color wasn’t my primary concern. I took two days to drive from the St. Louis area of MO to the Kansas City area to pick it up.

The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself).
So you stayed up all night, thought long and hard, and decided you want to name your designer sunglass hut The Sunny Rabbit. We don’t blame you, it’s a pretty cool name. Most would tell you that the next and most logical next step is to register your business as a DBA or at the state level. But, we’re here to tell you that’s wrong! Here’s why. We just talked about how the right business name can make or break your brand identity and in today’s digitally connected world, securing your brand identity across the web is equally as important.
Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
Nice setup Ryan. I’m looking more for the storage aspect than the sleeping in aspect. I like how you used the cap clamps to hold things in place. Do I understand right that those are the only things holding the side shelf units in place? That and maybe the ribs in the floor of your bed? So if you unclamp the cap, the whole side cabinets would just slide out?
It does sag a little bit, but not worryingly so. As I mentioned, it often rests on top of the large plastic boxes I place underneath, and I put in a small wooden brace at the entrance. You could definitely build it slightly smaller, or put in a more substantive center brace — like a sheet of plywood that fits into the groove of the bed liner and is the exact height you want.
A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information.
When we started putting together our water system we decided to look for a stainless steel tank. Even though plastic tank options are FDA-approved for potable water use, we still don’t like the idea of our drinking water being in contact with plastic for extended periods. Sure, they say it’s “safe,” but not long ago water bottles containing BPA were considered to be safe.

I’m a 60 year young widow who just bought a bright yellow 2003 S10 step side with the intention of camping in it. But I discovered that finding a used S10 step side topper is harder than finding hen’s teeth!! Buying a new one wasn’t an option. Just found a black step side topper for a Ford Ranger. Isn’t a perfect fit but it works. And the colors compliment each other although color wasn’t my primary concern. I took two days to drive from the St. Louis area of MO to the Kansas City area to pick it up.
2) I haven’t spent very many nights in full on winter conditions (that 12 degree night in Boise comes to mind!), so I can’t comment too much. It was fine for that… Mostly it was hard transitioning from the warmth of the cab to the frigid air while you are shifting things around and getting ready for bed, but then once you were inside the canopy it was fine. Lots of frosty ice on the inside windows, but in my sleeping bag all was well. It stays a little warmer in the canopy. Maybe I’m a wuss, but I didn’t want to spend an extended period of time dirtbagging it in my truck while I was ice climbing (I spent the first two months in Ouray, CO, sharing a rental), I just thought it would be too challenging/miserable to dry and manage gear in a confined space with the shorter daylight hours. I’d be perfectly content doing future weekend trips with this setup though!
Hospitality expert, Chip Conley founded and grew the Joie De Vivre hotels from a single San Francisco location to become California’s largest boutique hotel management company. How? He understood the value of a unique vision when it’s consistently applied. He created each hotel to reflect the spirit of a niche-oriented magazine that he felt represented his target market. Examples include the Phoenix (Rolling Stone), the Rex (The New Yorker), Hotel Avante (Wired), Wild Palms Hotel (Fast Company), Hotel Los Gatos (Town and Country), and the Water's Edge (Yachting). Obviously your inspiration doesn’t need to be a magazine, it can just as easily be a song, a group of words, or just a particular image. Find something that resonates with the customers you have in mind and design your store to reflect that vision.
There you have it! Now you have no excuses, you must start planning right away. Please remember this can take a lot of time and a lot of work, so be sure not to stare at your task list in its entirety too often. I don’t want you to get overwhelmed knowing all the things you must get accomplished. Just focus on the goal that is the most important and attack it, task by task. Need help organizing these goals? Check out my Goal Planning Worksheets here:

When you’re first starting out, it can be hard to imagine that there are entrepreneurs out there complaining of having grown too fast. But for some, it’s not a problem that’s welcome. For every Ben and Jerry’s, (Ben Cohen and Jerry Greenfield turned a rundown Burlington, VT gas station into an ice cream empire), there’s a Zynga or a Living Social that has enjoyed incredibly fast-paced growth, let their operating costs get out of hand, and then had to engage in mass layoffs when reality hit. If you’re enjoying fast-paced growth, make sure that this is reflected in your operating margins, not just the metric of revenue. You don’t want to be the butt of the old retail joke: “We’re losing a buck on every sale, but we sure are making it up on volume!”
In all you can spend under $1,000 and be setup in a great workshop. But I know how it feels when you’re shopping for new tools… and you think… “why not buy the top of the line so it lasts longer”… or “may as well get the best while I’m spending money”… those kinds of thoughts won’t only get you into big trouble with your other half… it’s also COMPLETELY wrong.
Finding reliable cellular service (and the internet that comes with it) is a constant challenge in vanlife, especially if you do computer-based work on the road. A cell signal booster like the WeBoost Drive 4G-X helps a lot in areas where service is spotty. It can take a weak cellular signal and amplify it into usable internet for web browsing and getting work done.
2. Just the basics—I’ve used a compound miter saw, circular saw, jigsaw, band saw, router, table saw, drill, finishing sander, belt sander, Dremel, oscillating multi-tool, bar clamps, and a Shop-Vac. I haven’t used a planer, jointer, or lathe. I’ve never owned a table saw but have used a circular saw or improvised with a router for a few long cuts.

Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.


A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.
In short – yes. The small business community is a diverse and eclectic collection of mom-and-pops, multi-generational businesses, one-stop shops, trendy boutiques, food trucks, lemonade stands, wine stores, bicycle stores masquerading as bars, and more. These entrepreneurs come from every walk of life and their motivations for starting small businesses are as unique as the businesses themselves. If you’re reading this, chances are you’re looking to join their ranks, and we say: “Go for it!”
We did a lot of research and landed on the Bestek 300W Power Inverter. We usually had our devices plugged in while we were driving so they'd be charged by the time we parked for the night. And if we were ever really in a pinch, we would plug it in for 10 minutes with the car off, then another 10 minutes with the car running until it was sufficiently charged.
Many small businesses in New York and New Jersey were forced to close following Superstorm Sandy because they lacked the insurance that would have gotten them back on their feet. That part is well known. What’s less well known is that this lack of proper insurance, coupled with the lack proper legal incorporation, resulted in many entrepreneurs seeing their personal assets come under threat.
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.
Your sense of space and how to use it will be slightly different depending on the focus of your craft. If you are building furniture with hand tools, you will be able to make do with less space (under 300 sq ft.) than if you’re using mainly power tools and building sets of cabinets (over 400 sq ft.). Some 3D mod­elling with a program like Sketch-Up or some 2D layouts on graph paper with scaled cutouts can allow you to experi­ment with arranging your space and how much of it you will need. You should include not only the tools, benches and storage that you currently possess but also enough room to tackle new types of projects and new tools that you antici­pate needing down the road. When you think you have a layout that works, test it out by mentally working through a range of different projects you might tackle and the needs you will have for material storage, assembly and finishing. Then revise as necessary; this process will allow you to hone in on a general square footage and layout ideas that will set you up to move forward.
Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on.  The rewards aren't usually good enough to compel me to purchase on their own.  But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.

If you have the available time, taking your DIY campervan for a test run (or two) is a great way to identify any problems while you still have access to tools, package deliveries, and a place to work. There’s just a lot that you can’t foresee until you live in your van. Taking it out for some short trips throughout your build will help you understand how you’ll actually use your new living space, what’s necessary, and what’s not.
Do you have a business license? Do you have a permit to open a food service establishment issued by the local health department? Are you applying for a permit to modify the building you wish to occupy? Do you have a health permit from the county health department? Do you have a signage permit? How about an alarm permit from your city or county fire or police departments? These are just a few of the questions you need to ask yourself.
Designing your retail store's interior is a topic that we've been looking at recently in an effort to help boutique merchants be more successful and thrive in today's digital era. From telling your brand's story and creating immersive shopping experiences, to putting together head-turning window displays and signage essentials, when it comes to retail, the devil really is in the details. As such, we want you to help you get the basics down pat. 
Garages are usually dark, which makes setting up task lighting a priority for a productive workspace. Track lighting is an easy option to install and gives your some directional overhead lighting, but it can cast shadows (especially if the light source is behind you while you work) and you’ll need another lighting source for task and overall room illumination. A simple, adjustable work lamp is helpful for soldering or when you need bright focused lighting.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
I wanted to have numerous outlets, and have enough elec­trical service that I did not have to worry about overloading circuits. There was already some lighting, so I simply picked off that line and added additional lights to keep things bright and cozy. I ran a 240V line for the table saw and jointer with a dedicated breaker. For wall outlets, I ran 14-3 wire, and split all the plugs, so that I can run one machine on the upper plug, and another on the lower plug of any outlet.
To make the most of your workshop oasis, look for a water dispenser that offers a choice between chilled and hot water. This will let you enjoy a cold, refreshing drink in the heat of summer rather than a lukewarm bottle that’s been sitting around gathering dust. You’ll also cut down on the amount of plastic your household goes through, which is a boon for the environment. In the winter, the hot water tap will also you to make a cup of tea or a mug of instant coffee on the spot. No matter what your taste, a versatile drink dispenser will keep you hydrated and happy while you work.
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
The Best Prices for Tools – Ralph shows you where to get the beast deals for the tools and equipment you need. You could buy them yourself from popular outlets like Home Depot, Lowe’s, and Amazon, but the Ultimate Small Shop guide shows you where to get these tools and equipment at cheaper prices. Of course, cheaper isn’t always better. These aren’t just cheap tools that are ineffective. Just good value for money on good tools.
I wouldn’t give up on Craigslist or garage sales.. For around $1K or less, you can pretty easily find the four big ticket items (TS, BS, Jointer and Planer) and have the extra $2K to spend on accessories, material, DC, other goodies, etc. The key is patience and persistence, and if applied correctly, you can have a fantastic setup for very little compared to purchasing new. If you are setting up a business, you don’t usually have the time to scour for good deals, but for a personal shop, there is no pressing need other than that itch to get something done.
Before you buy a single tool, you need to take a hard look at your workshop space. If your workshop is a freestanding building or empty barn, you can simply measure the perimeter and know that you have the entire square footage at your disposal including the wall space. If your workshop is tucked into the back of a garage or a corner of partially finished basement, you’ll need to plan your furnishings with cars and water heaters in mind.
This is a great project if you carefully consider your needs first. I left out the vise and tracks, but had no problem hand picking good 2x4 stock at the big box stores. I did use maple on the top sides in case I ever decided to add tracks, but it was not a budget buster by any means. The cabinet and drawers were a first for me and a great learning experience. I also added retractable casters so I can easily move the workbench around my shop. Love the workbench!
×