By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
Now, this is kind of an odd situation here, a few years ago when we bought this building there was a concrete block wall around here and a large drain right in the middle of the floor. Well the drain will certainly come in handy for any cleanup in the shop but the walls kind of left us when we removed those kind of left us a little divot and a little bit of damage here, so to make this nice and smooth so that our rolling workbenches will roll around real nicely we’re having to do a good bit of floor patch.
The core criteria of small business site selection will always be foot traffic and ease of access. In places like New York City, this means being by the subway or on a busy street. But for most of America it’s about considering traffic flow and parking accessibility. Ever see three gas stations at the same intersection? They are all picking off different traffic flows because they know customers are looking for the shortest possible detour.
If you want to spend as little as possible on a vent fan, the Fan-Tastic Vent 1200 (about $130) is your best bet. This fan has three speeds and manual controls, and it has the same quiet operation and energy efficiency of Fan-Tastic’s other fans. If you find that you need to use it while it’s raining, it’s easy to add on an Ultra-Beeze Vent Cover later on.
The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself).
Just a quick note about light spectrum. I went with 6500k because that’s what I like to film in. The daylight spectrum makes it easier for me if I decide to open the blinds, letting in some natural light. For the average woodworking shop, I think 5000k is probably a good choice, although some folks really enjoy the crispness of a 6500k light. But you should test them out for yourself to see what you prefer.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.

Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.
In order to ensure that the staff you’re bringing on board is the right fit for your small business, there’s a few questions that you should ask yourself during the interview process. Are they competent? Capable? Compatible and committed to your core business values? Do they fit in with the culture you are trying to build? And can you offer them fair compensation? Business expert and entrepreneur Alan E. Hall, calls this the 7 C’s to hiring. At the end of the day you want to look beyond the skills and experience they have on paper and make sure that they are willing and able to grow with your business.

Thanks for the quick reply. Sounds like you haven't had any big problems with the moisture. I'm in NoVA too, so that bodes well for me. I was considering finding some tyvek house wrap or something to go around the walls in addition to a plastic vapor barrier under the floor, but it sounds like that is not going to be necessary. I was also thinking I'd try to find a window AC unit to use like you did. I like how you mounted yours up high.

We don't have a Dometic CFX-50 in our van, but we wish we had gotten one for our build. This is a great little fridge that many vanlifers happily own. It’s rugged and durable, and it keeps your food cold for less money than many of the other fridges out there. It also has a nifty side-open lid, which makes it a lot easier to open with a lower clearance.


Use the scrap piece of plywood to map out the angle for the speaker stand legs. Decide the height you want for the base of the speakers, and make a mark on the plywood (32 in. for us). Mark the depth of the speaker (13 in.). Lay the 1x4 board assembly on the plywood, lining it up with both the corner of the plywood and the 13 in. mark from the edge. Scribe along the 1x4 board assembly, take the assembly away, and find your angle with a protractor or speed square (17 degrees for us). Cut that angle onto one end of the 1x4 board assembly.
Shops can range from functional spaces adorned with unpainted wallboard to beautifully finished, painted, and trimmed-out spaces. Ultimately, I think it depends on your budget and how important your surroundings are to your mindset as you’re working, or to your clients’ if they will be viewing your shop. If finishing your shop will improve the quality of the work that you will produce, thereby relaxing or inspiring you, or showcase for your clients the quality of the work of which you are capable, it may be a worthwhile invest­ment. A more finished space may also allow for activities like parties or even a weekly poker game (as long as drinks stay off the tools).
He’s also providing power to a cool light grid we’re building from several old fluorescent fixtures that we salvaged from past remodeling jobs. With six four-tube fixtures, we should get plenty of light. In a work space you want to install these lights high enough so they don’t get in your way when you’re moving materials but low enough to provide good even light.
Are your table saw accessories where you need them—when you need them? Follow reader D. E. Warner’s advice: Attach pegboard panels to the stand to hold the wandering herd of push sticks, blades, throat plates, wrenches and jigs. On an open metal stand with angle-iron legs, drill holes in the legs and bolt the pegboard in place. Here’s another super storage project using pegboard.

If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
You’ve probably considered what goods and services you’ll be offering, but have you researched the cost of sourcing your raw materials? How about the cost of turning those raw materials into your finished product? Do you understand how much you’ll need to charge for your products/services in order to cover the expenses of renting a space, paying employees, leasing equipment, and paying for permits and regulations? Moreover, have you considered if the answers to these questions will provide the kind of operating margin you’ll need to pay yourself a salary?
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.

The good news? There are a ton of free tools out there help you simplify and minimize the research required to secure your online identity. Among them is Namechk, a free username and domain search tool that helps you discover the availability of your business name across hundreds of social networks and domain extensions, all at once. Once you run a name search and confirm that it’s available for use both off and online, take the time secure your unique name both legally and on the web.
Large or small, most retail stores use one of three basic types of retail store layouts. Which type you use depends on the kind of store you have and the products you sell. For example, grocery stores usually use grid layouts because they are predictable and efficient to navigate. Boutiques typically use more creative layouts that allow businesses to highlight different products.
​One tool that has been notably missing from the earlier builds is a router.  There are so many reasons to own a router that I am not going to even try to list them.  But if you want to get the creative juices flowing, take a look at this Pinterest page.   The important thing to know is that this versatile tool can help you accomplish a number of tasks, everything from finishing edges to cutting dove tails.  
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
I spent so much time building organizers and filling in just about every square inch on the inside of my shop that I feel it will be better to show some of those in separate Instructables.  I made a couple of video tours to try to highlight some of the different aspects of my workshop.  I hope you enjoy them and I will work on making my future videos more stable.
Then there are material considerations, such as how to bring full-size sheets of plywood home to cut down to size (you don't). And safety and cleanup are two more concerns: Proper ventilation and dust collection, a cinch in a larger shop, can be quite a challenge (and a potential health hazard). Nevertheless, you can set up a great wood shop in a small space, and we'll show you what you need.
It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.

If you want the ultimate vehicle to customize for your DIY van conversion, the Sprinter is the van for you. They have enough headroom even for tall people to stand up, and enough interior space to design any kind of layout. They also typically have diesel engines, which means greater fuel efficiency and engine life (many diesel Sprinters have been known to make it past 400,000 miles). If you think you’ll be doing a lot of off-roading, the Mercedes Sprinter also comes in a 4x4 version.
It can become very difficult and time-consuming to constantly track the amount and purchase price of all your inventory, but it is hugely important to your bottom line. Every time you catch yourself saying, “Sorry, we don’t have that in right now,” you are leading your business in a very unhealthy direction. Not only does being out of something represent a lost sale opportunity, but in a world where consumers place a huge premium on their time, it could mean that you lose that customer forever while hurting your brand reputation in the process.
It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.
×