As part of my antique restoration work I do a lot of faux finishing – hence the supply of stains and paints. Since I didn’t want to dust the house, the new shop is not connected to the house heat and air system. But, having just finished our first winter I now know the shop didn’t get below 45 degrees – and, the oven in the corner can make the shop toasty in no time at all. 

Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.


Many DIY campervans have kitchen units that are directly behind the cab, sealing it off from the rest of the van. These layouts offer increased privacy and stealthiness, especially if you completely wall off the cab, and open up some space in the back of the van. This layout can be paired with a lengthwise bed, fixed bed, or convertible dinette bed. You can also place your propane and water connections right by the door, making refill easier.


The ARB fridge 50-Qt Fridge is the best of the best. ARB is an Australian 4x4 accessories company, and all of their products are built to withstand just about anything. The ARB fridge is extremely rugged, and features powder-coated zinc steel construction for the ultimate in durability. It can take a beating, and works just fine on inclines up to 30°.
What we're trying to do in providing these ongoing app cost resources is to frame the conversation for you. As noted earlier in this article, we're not suggesting that any of these different app types can't be lower than the lowest range shown or higher than the highest one. We are, however, trying to give you a sense for what a quality app built by seasoned professionals would look like.
Expert Tip: Banks are often reluctant to provide long-term small business funding. They prefer short-term loans that are associated with physical assets, which can then serve as collateral. So instead of just asking for a generic loan, maybe consider raising capital for specific equipment that will kickstart your new business, like an espresso machine or delivery vehicle.
Well, I hate pegboard, pegboard’s in every shop, people use the heck out of it. And what I wanted to do was start moving the tools in, get a few of them in and then maybe just build some little racks for the screwdrivers and a few of the things like that. But things that are like categories – like a drill, drill bits – just let the drill bits be right here. Certain things maybe that you don’t use all the time, hole saws or maybe brass for something like that, can go down in other drawers.

This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.


The key to success here is having clear processes written down, promoting from within whenever possible, and remaining open to change. You’ll want to balance your desire to educate your manager on how to manage your business with an openness to feedback and new ways of doing things. You’ll also want to take advantage of the technology available to keep you abreast of things like real-time sales data for all your locations, no matter where you are.
Household vacs are not designed to handle large quantities of sawdust or wood chips. Their filters clog up quickly, greatly reducing suction. While you can get away with using a small cordless vacuum for small messes, a shop vacuum offers greater power and capacity. Whether you already own a shop vacuum or are shopping for your first, consider purchasing disposable bags or a washable and reusable CleanStream filter.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
​There are some diverging paths that you could take at this point: some may want to get a router with a router table for edge work and improved joinery capabilities, some may want to start looking at some of the interesting 3rd party jigs - two of my favorites are the DowelMax and the Kreg Pocket System, but my recommendation would be to equip yourself to buy cheap stock.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
Disclaimer: The content on this website is provided for information purposes only, and should not be interpreted as professional advice. You should perform your own research and consult with a qualified professional. Individual results may vary. Through this website you are able to link to other websites which are not under the control of discountra.com. We have no control over the nature, content and availability of those sites. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.
Since your business name is often the first thing potential customers will see or hear, think of it as one of your key tools for leaving a lasting impression. The right name, like a firm handshake, can play a role in your brand’s perception. So make sure it’s strong, catchy, and unique, but most importantly sends the right message about your business.
It does sag a little bit, but not worryingly so. As I mentioned, it often rests on top of the large plastic boxes I place underneath, and I put in a small wooden brace at the entrance. You could definitely build it slightly smaller, or put in a more substantive center brace — like a sheet of plywood that fits into the groove of the bed liner and is the exact height you want.
However, instead of sharing a remodel update this week I thought I would do something a little different. This little voice in my head (sometimes called my husband) has been nagging me to add videos to my blog. I did a couple 1 minute hands-only videos a few months back, but I have been seriously afraid to get in front of the camera. The nagging voice finally won out and I bit the bullet and got in front of the camera for you today! I decided to do a video for today’s post instead of just writing out a boring list. And while editing the video I came to the realization that I am very expressive when I talk. Wow! I use my whole face when I talk. I guess that’s what people meant when they said I am dramatic. Oh well, this is me so I hope you enjoy today’s video about how to build a woodshop on a budget.
Apps begin to get more complex—and costly—once user authentication is involved. The main reasons for that are all the other expectations that come with user authentication. Typically, they include interacting with data (e.g., favoriting an article), syncing data across devices, push notifications, and perhaps collaborative features (e.g., inviting a family member).
Ideally, the stands should lift the speakers to roughly ear level of a sitting person. This is important because it aligns the ​subwoofers and tweeters relative to the ear and achieves the best balance of sound. The high frequencies are often missed when speakers are placed too high or too low. Speakers placed on a shelf or table often cause the surface to vibrate, thus distorting bass. These speaker stands isolate the speaker's vibrations from the floor, allowing you to hear the bass from the speaker and not the vibrations from a shelf, table or floor. Speakers come in various sizes and shapes, so the height of your speaker stands is dependent on your unique speakers. For this project, we give you the dimensions suited for the speakers shown in the photo, but you can alter the design to fit your individual needs.
Now, photographs or video tape will also be very useful especially to pass along to your insurance adjustor. Now the problem is this documentation won’t help you at all if it’s lost or destroyed so consider saving your information electronically. Take your photos with a digital camera and create a list of all your valuables, and save both in a computer file. This file can be saved to a disk you can keep at work or upload it to a website that you can access it from anywhere including your home.
Now, we’ve already applied some resurfacer to fill up some of the deeper holes and after that dries overnight we’ll use a floor leveling compound tomorrow morning to really smooth everything out. Leveling compound is more fluid than the resurfacer so it flows into all of the low spots to even out the surface. Now, this won’t look like a finished floor when Tim’s done but it should do the job for our shop. Now, while he wraps up this Emily has a Best New Product that might be a great addition to your workshop.

Shop layout is all about making the best use of space. Place your machines so that you have adequate “safe space” that you need to work around them. The “buffer area” beyond that is the amount of room you need to run large stock though a given machine, keeping in mind that buffer areas can overlap between machines. If you want to get more organized, buy some 1/4-inch squared paper, make scale models of each machine including the safe space around each, and place them on your model shop layout. Remember that buffer areas need to be long enough to put an 8' sheet through a table saw, or a 6' plank through your planer, for instance. I raised my planer, so that I can use the area above my router table to pass long planks through the planer – all it takes is some modelling, and a little shuffling, and you will find the layout that works for you. Each space will have chal­lenges; I had the area under the stairs that was wasted space, so I installed the dust collector there.
Expert Tip: Banks are often reluctant to provide long-term small business funding. They prefer short-term loans that are associated with physical assets, which can then serve as collateral. So instead of just asking for a generic loan, maybe consider raising capital for specific equipment that will kickstart your new business, like an espresso machine or delivery vehicle.
Expanded polystyrene (EPS) is an open-celled foam board (think styrofoam) that is the cheapest of all the foam boards. It does work, but we generally don’t recommend using EPS in your van. It insulates less than XPS (R-4 per inch), and the gaps between the foam cells allow moisture to penetrate, which degrades the insulation over time. Polyiso and XPS are much better choices for a slightly higher cost.
Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.
Google - If you have any question in the world, you can google it and probably find the answer, lol. However, I know your concern is how accurate the information is that you are getting. You also want to make sure that when you find some great knowledge, that it's leading you in the right direction. So if you google "how to make money from my Instagram following" or "how to drive buyers to my Instagram account", then you want to find actually step by step instructions, that will actually lead to a real result. Sometimes that isn't always the case. So search and try to put the pieces of the puzzle together to help you, but just know that it probably won't be handed to you on a silver platter like my webinars are. If you are having problems with your SEO for google, then I recommend that you get my Google SEO Webinar.
Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.

Ultimately, I did this to inspire my son. I want him to look at what I have done as a father and be proud. But I also want him to grow up into a strong man who faces fear in the eyes and doesn’t back down because of a challenge. I want him to say to himself one day, “if my dad built Optimus Prime, then I can do anything I want to do in life.”  I want him to succeed in every possible way imaginable, even when I am no longer around to help him through those challenges.

When starting your small business, the easiest way to go about choosing a business name is to approach the task the same way you approach building new relationships. Did we lose you for a second? Here’s what we mean. It takes just one-tenth of a second for us to judge someone based on a first impression. There are endless relationships that instantly blossom or never get off the ground based off of this one simple fact. Most of us, even if it is on a subconscious level, understand this. Which is why when we meet someone that we are trying to impress, we make an attempt to adjust our appearance, body language, even the way we talk, to ensure we are putting our best foot forward.
A grid floor plan, also called a straight layout, is a very efficient use of both floor and wall space. With fixtures and displays running parallel to walls, a grid floor plan maximizes every inch of available floor space, including the corners. Grid layouts are easy for customers to navigate and for store owners to categorize. Plus, they offer plenty of end cap and feature wall exposure for promotional items and seasonal products.
I’ve been living out of my Mazda 3—not the hatchback version!— for over two years now. I love the gas savings (standard transmission; I can get up to 40mpg) and the ease of getting around places. I don’t love that I can’t lay flat (hurts the back) and that organization is tricky. However, there are certainly ways to make it work. Ryan linked to one article and there are two others that shed light on some important aspects when going on a long road trip like this.
In many ways, skoolies are the ultimate in mobile living. The big advantage here is space - there’s tons of room for couches, beds - even a full bathroom - and you can easily accommodate families and other larger groups. There are also some really impressive skoolie builds out there that are nicer than actual houses, and it’s a whole lot cheaper to convert a bus than to buy a similar-sized RV. Skoolies come in multiple sizes, from “shorties” to full-sized buses.

To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
Excessive growth is of course, a good problem to have. However, after stabilizing from the startup process, small businesses more commonly grow steadily before approaching a plateau. This is completely normal and it is often at this point that you’ll need to go back to your business plan and carry out what is known as a SWOT analysis. This includes an analysis of a company’s current finances, the competition, and SWOT: Strengths, Weaknesses, Opportunities, and Threats. Renovation of your product line, rebranding, and seeking investment for expansion are all potential results of this SWOT analysis. Once again, the key here is being data-driven and always staying hungry. The successful small business owner is always looking for the incremental improvements in their business that when added up, make all the difference.
Since grid layouts are used in most grocery, big box, and convenience stores, they create a familiar feel to customers. However, due to this familiarity, they tend to impart a grab-and-go experience. A grid layout can be a good choice for small retailers who shelf-stock inventory in quantity, like toys, books, magazines, specialty foods, kitchenware, and home goods. However, it’s not ideal for retailers who want to create an upscale, branded environment that invites relaxed browsing.

Electricity was something we didn’t want to worry about at all in our van, so we went big from the beginning. We bought Renogy's 400-watt solar kit and two VMAX 155ah batteries. We mounted three of the panels on our van’s roof, and the fourth we attached to a folding stand made out of PVC so we could roll it out as needed. While the system works great and keeps us charged up, in hindsight it was a little bit of overkill - especially since we added a battery isolator.
In short – yes. The small business community is a diverse and eclectic collection of mom-and-pops, multi-generational businesses, one-stop shops, trendy boutiques, food trucks, lemonade stands, wine stores, bicycle stores masquerading as bars, and more. These entrepreneurs come from every walk of life and their motivations for starting small businesses are as unique as the businesses themselves. If you’re reading this, chances are you’re looking to join their ranks, and we say: “Go for it!”
Household vacs are not designed to handle large quantities of sawdust or wood chips. Their filters clog up quickly, greatly reducing suction. While you can get away with using a small cordless vacuum for small messes, a shop vacuum offers greater power and capacity. Whether you already own a shop vacuum or are shopping for your first, consider purchasing disposable bags or a washable and reusable CleanStream filter.

Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.
In addition to keeping your workshop comfortable with climate control add-ons, don’t forget to keep your body in optimal condition as you work. A water cooler tucked away in the corner of your workshop will provide a big quality of life boost and allow you to keep at your projects without having to run to the kitchen for a glass of water every time you feel thirsty.
When we started putting together our water system we decided to look for a stainless steel tank. Even though plastic tank options are FDA-approved for potable water use, we still don’t like the idea of our drinking water being in contact with plastic for extended periods. Sure, they say it’s “safe,” but not long ago water bottles containing BPA were considered to be safe.

Using six pipe cleaners, you can make your own skeleton. Bend one pipe cleaner into two for the backbone. Twist another around the bottom of the backbone to make into the legs. Do the same for the arms. Join two pipe cleaners and twist them around the backbone leaving some space forming a ribcage. Ultimate Small Shop Woodworking Twist the last pipe cleaner for a head and glue on some eyes. Hang with a rubber band for a bouncing effect. Your kids will love making Halloween crafts with pipe cleaners. But be careful when cutting and keep them out of their mouth. Going trick or treating? Why not make a special jug to collect candies? Cut off the top two inches of a gallon milk jug. Soak to remove any labels. Paint orange. Once dry, paint or stick on eyes nose and mouth resembling a Jack O’Lantern. Use fluorescent paint for a nice effect. The jug can be kept for future reuse. Using glue and food coloring, you can make a see-through painting. Paint a Halloween image onto a piece of plastic wrap. Before the mixture dries, put another piece of plastic wrap on. Cut it out and hang it in front of a light source for a see-through effect. You could also frame the plastic pictures using wood or cardboard if you want them to be longer lasting. Make some hand printed spiders. Ralph Chapman Ultimate Small Shop Apply black paint to your palm and 4 fingers leaving out the thumb. Place palm onto a piece of paper. Turn the paper 180 degrees and print again making sure the palm overlaps. Add some wiggly eyes using either paint or sticks. This is suitable for even 2 or 3-year-olds. Make your own blood. It is less expensive than buying ready-made blood from the Halloween shops. It’s not difficult; all you need is Karo syrup and food coloring. While you’re at it, why not make some slime using glue, water, and borax powder. This is an advanced Halloween craft, so take your time and be careful. Using apples, you can make dried, shrunken heads. Peel the apples and coat with a mixture of lemon juice and salt to prevent browning. Carve out a face of eyes, nose, and mouth. Do not worry about the finer details as they will probably be lost when the apple dries. You can use whole cloves for the eyes and rice grains for the teeth. Let the apples sit out in a warm place for about 2 weeks. If you don’t have 2 weeks, you can speed up the drying by putting them into an oven on the lowest temperature for about 45 minutes and then dry out naturally for the next 2 days or so. Ultimate Small Garage Clock Shop Once dried, they shrink and deform into weird and scary looking faces. Says Angie Maroevich, “You don’t have to spend a fortune on commercial Halloween supplies to have a great party.
Wide aisles also prevent the dreaded butt brush, a term coined by top retail consultant Paco Underhill. His studies show that both women and men avoid tight or crowded aisles where they might brush bottoms with other shoppers. Really, this is a thing! Learn more about Paco’s retail research and insights in his book, Why We Buy: The Science of Shopping.

After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appro­priate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with hom­eowners and builders to make sure that the work will meet code and will endure.


Shop looks great Marc, I see the Clear Vue in the picture. I love mine, I used 8″ PVC for the main trunk line and came out of that with 6″ drops. It works great. I wound up building a collection bin instead of using a can, only thing I didn’t do was make the bin big enough. It holds more than the typical can but I still should have made it with more capacity. The 1800 with the 5 hp motor is stout.
So after 14 years in our previous location, my company moved to a new shop last month. My shop went from 1600sqft split into 2 bays with the kitchen in between to a contiguous 2950 sqft. Still don't know why the the office portion needed to grow by the same percentage when there were already 10 empty cubes at the old office, but thats an argument for another day. The boss got his 500 sqft office so he is happy.
First, let's dump that hand powered saw/miter box.  It gets the job done, but it takes forever.  We're still on a lean budget, but shelling out ~$110 for a 10 inch electric miter saw makes a lot of sense.  This won't be your forever saw, but it should do fine for most projects.  It can handle up to a 4x6 stock which will cover 99% of what a beginning wood worker will throw at it.  
Now, this is kind of an odd situation here, a few years ago when we bought this building there was a concrete block wall around here and a large drain right in the middle of the floor. Well the drain will certainly come in handy for any cleanup in the shop but the walls kind of left us when we removed those kind of left us a little divot and a little bit of damage here, so to make this nice and smooth so that our rolling workbenches will roll around real nicely we’re having to do a good bit of floor patch.
Wide aisles also prevent the dreaded butt brush, a term coined by top retail consultant Paco Underhill. His studies show that both women and men avoid tight or crowded aisles where they might brush bottoms with other shoppers. Really, this is a thing! Learn more about Paco’s retail research and insights in his book, Why We Buy: The Science of Shopping.

Congratulations on your new shop and all your success. I’ve watched all of your videos and someday if I have the money I would love to join your guild. I started a small workshop in my grandparents basement and someday I hope to start a small bussiness. Your website and videos have been the most informative and the most inspirational to me as a beginning woodworker. Thank you for sharing all your tips and hard work with people like me. I look forward to watching your videos for years to come.
We use this fan for extra circulation when it’s hot, and to get the air moving when it’s cold at night and we have all the windows closed. We also keep it on for our dogs while we’re driving. There are cheaper 12V fans out there, but generally the cheaper the fan the more power it draws. The Endless Breeze is a great little fan, and it’s definitely worth getting for the added ventilation.
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Hey Ted! If you mean to ask whether you could sit up from one of the vertical sidebins and have enough headroom under the Leer 122, I think that would be a no. You’d have to build the sidebins to be a little shorter. At least with my truck, that would be the case. Perhaps with a full-size pickup you would have enough room thanks to the overall size increase of the canopy as well.
There are many inexpensive alternatives lying around the house or at your local store you can use to create a Halloween theme that will impress all your friends.”One of the most popular party favors is a framed picture of the party guest taken at your kid’s party. He or she could be showing off a silly hat or party costume, performing an outrageous party game stunt, or wearing a face full of frosting and ice cream. Having party guests create their own make-and-take frame to display this memorable photo makes it an even greater treasure for the memory box. Start with a plain square of cardboard with an opening the size of your picture. When the decorating is done, Ultimate Small Shop Reviews simply glue the picture to the back of the frame. Why not turn that Cooking Interest, Comic Book Collecting, or Your Retro Clothing Collection Into A Home Based Business Venture! Most people enjoy hobbies they have pursued with great enthusiasm for years. Even though they may find their leisure activities fulfilling and enjoyable they never imagined making money with a fun hobby! Are you one of these gifted individuals? These talented individuals might have a passion for sewing fabulous original wardrobes, marvelous hand knitted items, furniture making, creative paintings, photographs, jewelry art, greeting card design, doll making, original toys, baby clothing, candle making, quilting, calligraphy, fancy soap making, about anything you can imagine! Crafting is actually a great way to start a home business on a shoestring. You might want to start on a small scale by offering your creative work to friends and family. Later on, once you have enough products, you might decide to rent a booth at local flea markets or crafts shows to display your work. As you may know, the Arts And Crafts Industry Is Enjoying An Amazingly Phenomenal Popularity. People are eager to purchase hand made clothing, furniture, custom made keepsakes or jewelry. If you have the creative talent this is one business you should consider! A friend, Joyce, diverted her obsession with candle making into a thriving business. She started by selling her hand made scented candles to friends and neighbors. Word of mouth spread about her candles. Soon she was receiving enough orders to keep her very busy. Joyce throws house parties to sell her candles and also takes custom orders from ads she runs in local newspapers. Next, she plans to take her candles to the stores and malls in her area.”Today is life – the only life you are sure of. Make the most of today. Get interested in something. Shake yourself awake. Develop a hobby. Let the winds of enthusiasm sweep through you. Live today with gusto.”Our hobbies help us to relax and forget our everyday problems and troubles. We are all experts in one or more fields of our lives. Ultimate Small Shop program But I am sure that not everyone has a hobby that makes money for him/her (except, of course, if you love your job).Just imagine, wouldn’t it be great if you could have money making hobby? You could get involved even more with what you already love to do, you could treat your family and friends with the extra cash, or… even quit your current job that you probably hate.

James Hamilton (or “Stumpy Nubs”) is a self-taught tool expert, engineer, writer, teacher and video producer. In 2008 he went into woodworking full time, creating a weekly Internet woodworking show that focused on the workshop itself. Now, Stumpy Nubs Woodworking has grown into one of the most popular multi-media woodworking resources in the industry.
However, instead of sharing a remodel update this week I thought I would do something a little different. This little voice in my head (sometimes called my husband) has been nagging me to add videos to my blog. I did a couple 1 minute hands-only videos a few months back, but I have been seriously afraid to get in front of the camera. The nagging voice finally won out and I bit the bullet and got in front of the camera for you today! I decided to do a video for today’s post instead of just writing out a boring list. And while editing the video I came to the realization that I am very expressive when I talk. Wow! I use my whole face when I talk. I guess that’s what people meant when they said I am dramatic. Oh well, this is me so I hope you enjoy today’s video about how to build a woodshop on a budget.

Ralph has three decades of professional experience in using workshops and setting them up, and it certainly shows in his Ultimate Small Shop guide. You’ll find all the important information you need to put together your own workshop, including how to save money when putting one together; all the tools and equipment necessary to run a workshop; tips for choosing the best equipment; factors that should be considered when buying things for the workshop; and so much more. If you’ve considered setting up a workshop but feel you don’t have the time, space, or money – then you need to check out Ultimate Small Shop – How to Set Up a Complete Small Workshop on a Budget.
After you are done narrowing down your list of business goals, you are now ready to plan out when they will be accomplished. Just remember, nothing is set in stone so if you need to remove or add something to your business goals later down the road, that's okay. It happens to me ALL THE TIME. Sometimes our priorities shift or things didn't go as planned and you need to make changes. 
By building your own workshop machines and jigs, you can create customized tools that include all of your favorite and much-needed features for less than half the cost of commercial tools (plus, get bragging rights for having the coolest woodworking shop in town). All you will need is a drill press, table saw, some common tools, and patience. Then, you can start following these step-by-step instructions to create homemade machines such as a sliding-top router table, jigsaw, downdraft dust collection table, a 24” band saw and more!
A warning out of concern and love for my fellow 'ablers. A framing nailer is a VERY dangerous tool. Not something to loan out willy-nilly to just anybody. For a small project like this it's just not going to save a lot of time. Most of us are better off burning the extra calories that swinging a hammer uses anyhow. Emergency rooms are seeing a lot of visits because a lot of guys see these on TV and at your big box stores and think they look cool. They are only marginally safer than shooting at the nails with a pistol. (Hmmm...). Be careful, PLEASE.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.

You can typically find paneling in pine and cedar. Pine is cheapest, looks fine, and will do the job. Cedar is more expensive, but it looks and smells awesome - and it’s resistant to mold and mildew. Paneling comes in different thicknesses, but we recommend using ¼” (5/16”). Thinner paneling weighs less, costs less, takes away less interior space, and will bend with your van’s contours.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
This is a great project if you carefully consider your needs first. I left out the vise and tracks, but had no problem hand picking good 2x4 stock at the big box stores. I did use maple on the top sides in case I ever decided to add tracks, but it was not a budget buster by any means. The cabinet and drawers were a first for me and a great learning experience. I also added retractable casters so I can easily move the workbench around my shop. Love the workbench!
We think you’re going to find our newsletter and blogs useful and entertaining to read. Because we’re all woodworkers here at Popular Woodworking, we generate a huge amount of valuable woodworking information that we cannot possibly cram into the printed magazine. So the newsletter and community are both great places for us to share what we know with you.
However, another critical component to small business success is being self aware. With a variety of tools at your fingertips, tracking basic accounting can be fairly simple. Still, in order to be strategic about how you spend your money, properly leveraging these tools will still require a little bit of legwork. What used to take you eight hours might now only take one hour. But if you’re not willing or able to run through your financial tasks on a regular basis, bringing in a bookkeeper or accountant might be your best option.

To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
​One tool that has been notably missing from the earlier builds is a router.  There are so many reasons to own a router that I am not going to even try to list them.  But if you want to get the creative juices flowing, take a look at this Pinterest page.   The important thing to know is that this versatile tool can help you accomplish a number of tasks, everything from finishing edges to cutting dove tails.  
When starting your small business, the easiest way to go about choosing a business name is to approach the task the same way you approach building new relationships. Did we lose you for a second? Here’s what we mean. It takes just one-tenth of a second for us to judge someone based on a first impression. There are endless relationships that instantly blossom or never get off the ground based off of this one simple fact. Most of us, even if it is on a subconscious level, understand this. Which is why when we meet someone that we are trying to impress, we make an attempt to adjust our appearance, body language, even the way we talk, to ensure we are putting our best foot forward.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 

Food in bear country… When I was in *real* bear country, like in the Sierras, I always kept my food and scented items in the provided bear lockers. Any of the trail heads or camping areas will have bear lockers. Other than that I never really worried about. Just kept it in the cab, yeah. But the Sierras were the only place I went with any considerable bear problems.
As part of my antique restoration work I do a lot of faux finishing – hence the supply of stains and paints. Since I didn’t want to dust the house, the new shop is not connected to the house heat and air system. But, having just finished our first winter I now know the shop didn’t get below 45 degrees – and, the oven in the corner can make the shop toasty in no time at all.

We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.
×