Above all, remember that all of these elements can form part of your negotiation. Unless you are pursuing a highly desired space in a hot rental market, there is usually a point of leverage available to you in every lease negotiation. When it comes to getting the best possible deal in these situations, you’ll want to seek quality professional advice, this will normally include a broker and real estate lawyer.

Calculating the size of your desired parking lot is easy. The rule of thumb is to have a parking spot for every three customers. Determining traffic is trickier and potentially more lucrative. To help, we wrote an article on how to calculate your desired foot traffic. If you want to calculate your desired vehicle traffic, you can refer to our article on how to choose a location for your restaurant.


As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.

Garages are usually dark, which makes setting up task lighting a priority for a productive workspace. Track lighting is an easy option to install and gives your some directional overhead lighting, but it can cast shadows (especially if the light source is behind you while you work) and you’ll need another lighting source for task and overall room illumination. A simple, adjustable work lamp is helpful for soldering or when you need bright focused lighting.
Hey! Thanks for stopping by and checking this out, I appreciate your comments as well. It is something I really should do… I’ve done a bit more research on this since I initially posted it, and it is less intimidating the more I read. It just comes down to actually doing it and spending some more money, I guess. I’ve got the 22RE in my truck… I still need to look more into the alternator aspect though.
​There are some diverging paths that you could take at this point: some may want to get a router with a router table for edge work and improved joinery capabilities, some may want to start looking at some of the interesting 3rd party jigs - two of my favorites are the DowelMax and the Kreg Pocket System, but my recommendation would be to equip yourself to buy cheap stock.
Hey Ted! If you mean to ask whether you could sit up from one of the vertical sidebins and have enough headroom under the Leer 122, I think that would be a no. You’d have to build the sidebins to be a little shorter. At least with my truck, that would be the case. Perhaps with a full-size pickup you would have enough room thanks to the overall size increase of the canopy as well.
Ideally, the stands should lift the speakers to roughly ear level of a sitting person. This is important because it aligns the ​subwoofers and tweeters relative to the ear and achieves the best balance of sound. The high frequencies are often missed when speakers are placed too high or too low. Speakers placed on a shelf or table often cause the surface to vibrate, thus distorting bass. These speaker stands isolate the speaker's vibrations from the floor, allowing you to hear the bass from the speaker and not the vibrations from a shelf, table or floor. Speakers come in various sizes and shapes, so the height of your speaker stands is dependent on your unique speakers. For this project, we give you the dimensions suited for the speakers shown in the photo, but you can alter the design to fit your individual needs.
As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.

The good news is that when you’re starting your small business, you now have the tools to take a data-led approach to choosing the right store design. For example: Not sure what type of music gets your customers in the mood to spend? Simply choose a few different styles and display a different one each week. After the test is complete, analyze sales data to help you identify what could be impacting sales. The key to getting accurate results from this kind of test is to avoid switching up the other variables in your store that can impact sales, such as signage, or testing one type of music during a regular business week and another type during a holiday week. For more details on how to create controlled in-store experiments, you can check out Lean Retail 101

However, instead of sharing a remodel update this week I thought I would do something a little different. This little voice in my head (sometimes called my husband) has been nagging me to add videos to my blog. I did a couple 1 minute hands-only videos a few months back, but I have been seriously afraid to get in front of the camera. The nagging voice finally won out and I bit the bullet and got in front of the camera for you today! I decided to do a video for today’s post instead of just writing out a boring list. And while editing the video I came to the realization that I am very expressive when I talk. Wow! I use my whole face when I talk. I guess that’s what people meant when they said I am dramatic. Oh well, this is me so I hope you enjoy today’s video about how to build a woodshop on a budget.
So before you start to consider fixtures and displays, think about the product positioning throughout your store. Where are your evergreen, seasonal, limited availability, and sale products going to be featured on an ongoing basis? This process is called product mapping. Following is an example of a product mapping plan that features a mix of product categories in defined areas:
The on the go mode is ideal for when I’m just driving all day and need to pull over and get some rest, be it in a parking lot, a residential cul-de-suc, or wherever. I usually toss a couple of items in the cab of my truck and crawl into the “coffin” sleeping arrangement for a quick night’s rest, but I can also crawl in without placing anything in the cab.
×