It does sag a little bit, but not worryingly so. As I mentioned, it often rests on top of the large plastic boxes I place underneath, and I put in a small wooden brace at the entrance. You could definitely build it slightly smaller, or put in a more substantive center brace — like a sheet of plywood that fits into the groove of the bed liner and is the exact height you want.
It all depends on what you care about most. Putting your kitchen by the side door could simplify refilling your water and propane tanks. Putting it behind the driver’s seat creates a nice, open feel in your van. Right behind the cab makes your van more private, while all the way in the back is a different twist on most van layouts out there. Some vanlifers even have kitchens that pull out of the trunk on drawers for cooking outside.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
Use this model whether you’re looking to turn your team of one into a two-person shop or you’re hoping to build out your marketing department to a team of 10 or more.  By focusing on the skill sets your business needs to be successful — rather than on the resume of an individual candidate — you’ll ensure vital functions are covered while expanding in a sustainable way.
Of all the LED lighting options, puck lights are the most difficult to install. You’ll have to run wiring behind the ceiling/walls for each light. And you’ll need to cut a hole with a hole saw to recess the lights into the ceiling. But with some preparation and care it's not too difficult. We have full instructions for installing LED puck lights in our epic electrical post.
Boy you guys are spoiled, lol. There will always be at least some echo in the shop. I wouldn’t judge the acoustics based on this video though since the shop was still being put together at the time. No cabinets and no floor tiles, so the echo is to be expected. Have you seen the latest video? http://www.thewoodwhisperer.co.....rock-star/ The sound is dramatically improved over the Dream Shop video and all I did so far was add a few floor mats here and there. By the time the cabinets are in and I get some nice rubber floor tiles in place, the sound should be at least to the level of the old shop if not better. Right now though, my priority is on building a bed and I do consider the current sound to be “acceptable” for web videos. I’ll focus on tweaking things when I finally get some spare time. Considering adding some acoustic tiles to the ceiling.
Since your business name is often the first thing potential customers will see or hear, think of it as one of your key tools for leaving a lasting impression. The right name, like a firm handshake, can play a role in your brand’s perception. So make sure it’s strong, catchy, and unique, but most importantly sends the right message about your business.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
Calculating the size of your desired parking lot is easy. The rule of thumb is to have a parking spot for every three customers. Determining traffic is trickier and potentially more lucrative. To help, we wrote an article on how to calculate your desired foot traffic. If you want to calculate your desired vehicle traffic, you can refer to our article on how to choose a location for your restaurant.
Trademarking is a lot less expensive than most people think (although enforcement is another thing entirely), but make sure to do your research! If someone else is already using your proposed name, your application will be rejected right away and you will not only lose your application fee, but the time invested would have been in vain. And as you know, time equals money.

Hey thanks for the great insight on a pickup camping setup! I just purchased a 2002 tundra with a 74″ bed. Picking it up in Denver in a week and driving it to Durango and then around the southwest. I mainly decided on a truck for a mobile place to keep my dog(that doesn’t have an interior he can rip to shreds), but I am thinking of building a setup similar to yours. You haven’t used yours with a canine companion have you? Any suggestions on keeping it dog-friendly, dog-comfortable and dog-proof? I will be keeping him in the back while at work and such and will be camping in the back with him and possibly another person.
Now, another thing we’ve recycled that’s kind of unusual, all the wood walls you see here were actually and old backdrop that we used on a show a couple of years ago, perfect for our wood walls we need. Now, to store some of the tools, we have we created this simple little shelf unit out of cedar. And you know it kind of adds some of that warm wood feel to a shop, which I wanted it to look more like this than just plain painted walls.
On-demand apps incorporate many of the elements seen in apps with logins and social features. Like ecommerce apps, they also include a transactional component, because users need to purchase goods and services. Unlike social and ecommerce apps, however, on-demand apps essentially require two completely unique user experiences. For example, an Uber driver needs advanced mapping and routing functionality while a rider doesn't. Similarly, the driver doesn't need to do a payment while a rider does.
I have been working on building out the space, starting with a new welding table and small material/saw rack. I was able to dedicate a 20' x 28' area to fabrication. I need to figure out some things like angle grinder storage, fume exhaust hood and cold saw set up, but I will get there. Power is one nice thing with a 400A 208VAC 3ph supply panel. Also got the compressor in a sound dampened closet with cooling so the noise level is down significantly. Oh ya, dedicated 15 ton AC for the shop has been nice.
Time spent earnestly involved in the creation of something designed and made with one’s own ingenuity can be quite enjoyable. So now when I don’t feel motivated to do more practical things I often turn to an idea about some device or other that I’ve wanted to try making but never got around to. Ultimate Small Shop Videos I can recall many such improvised devices that gave me satisfaction and enjoyment.Ideas for things to make come from many places. Most often the idea comes from some need. I do a lot of keying of text using a computer keyboard. I tend to keep the room temperature a bit cool, cool enough that my hands become uncomfortable. I ended up rigging a length of electrical heating tape wound in a large coil-shape to surround the keyboard. Tying the heat tape to a large piece of cardboard keeps it in place. It does a nice job of keeping my hands warm. I can leave the room temperature set where I want it. As far as I know, you can’t buy anything like that. Building and inventing improve my understanding of mechanical devices and materials. It gets easier to manipulate and modify the physical things that are so much a part of everyday living. With effort and imagination, often new devices can be made or existing ones improved for my enjoyment and satisfaction. Both intuition and logic are used to make a homemade gizmo. The more the two abilities are used together, the more powerful the combination becomes. A strong partnership of reason and creativity helps a person to produce and enjoy life. It is fun and satisfying to conjure up and build simple devices. Those created items command more appreciation than more casually acquired, purchased items. And it feels good proving that imagination and ingenuity can make life better. The process of invention seems magical. The mind pieces together what it has already made some sense of into something new. It seems that even the most obscure result can eventually be produced. The grass hut and the keyboard heater each gave me a little taste of that magic. Until recently crafts were usually sold locally or, at best, regionally. Now you literally have the whole world at your fingertips! Some of you may choose a gradual progression from selling to friends to selling at fairs and shows, to retail selling … and so on. Others may decide to jump directly from selling within their circle of friends to the worldwide Internet market – the costs are low enough that this is surprisingly doable. My first career was as a special education teacher. After 15 years of teaching, I earned an MBA degree followed by CFA (Certified Financial Analyst) certification. Ultimate Small Shop Pdf Download After 15 years in finance I was a vice-president and portfolio manager of a major insurance company before I was downsized.
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
Use this model whether you’re looking to turn your team of one into a two-person shop or you’re hoping to build out your marketing department to a team of 10 or more.  By focusing on the skill sets your business needs to be successful — rather than on the resume of an individual candidate — you’ll ensure vital functions are covered while expanding in a sustainable way.
The good news is this: You are not a statistic. Think about this — if it was reported that small business owners over the age of 50 were more likely to succeed, would you wait until you were 50 to start a small business? Not likely. You would start when you felt ready. And that’s the point — only YOU can know when it’s time to take the plunge. Likewise, only you can make the intelligent decisions that ultimately mean the difference between success and failure when it comes to launching your business.
Again, it is the inspiration I have (hopefully) given my son. To never be afraid to try, even at the risk of failure. If you don’t have all the answers, go with the knowledge you do have and trust everything else will fall into place. I am no millionaire; I have entered into a lifetime of debt because of what I’ve done with this build. And I’m going to try and keep it on the road as long as I can. I am not getting any help from Hasbro and Paramount Pictures, so I am looking for help with sponsorships.
Congratulations !! I think 62 days is quick ! thats a big project. Now that its done and you got to get everything else set up it kinda sucks that you will also need to start making the payments, yuck. However I think it will be a good investment as your show continues to grow . I certainly love it ! I look forward to what you have in store. Thanks

If you live where summers get hot and humid, you may need more than a fan to keep cool in your workshop. Fortunately, air conditioners will both dehumidify and cool your space — and you don’t need a traditional window to get the job done. Instead of a residential window unit, consider a freestanding portable air conditioner that you can use as needed on hot days.


The other aspect that separates the cost of ecommerce apps is the payment itself. As users add products, they'll need to check out and perform a payment transaction. Some of the tools above bundle in payment solutions. Alternatively, you'll have to integrate with payment gateways like Stripe, Braintree, Authorize.net, etc. Ecommerce apps that fall into this category include Amazon, Stitch Fix, Honest, and many others.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
I framed in a 4x8 Garden Shed on the back.  I didn't want it so deep that stuff would get buried in it.  I need to take an updated picture of the back.  These pics were from early on and I have changed some things in the organization.  I used similar framing techniques and built a lean to roof attached with metal hangers.  I chose to use clear corrugated roofing to allow natural light into this shed.  You can see the 2 shopvacs that were originally part of my simple vacuum system.  I have removed them and found that I get better airflow using an electric leaf blower with the vacuum attachment hooked up to my system.  There is a large metal trashcan with a dust collection separator to collect the larger pieces of saw dust and chips.  My air compressor is on a shelf on the right now and I ran a hose through the wall and to a 25 foot reel attached to the ceiling.  I wired separate switched for both on the inside of my shop.  These systems work extremely well for a small shop.  The wall provides some insulation from the overwhelming noise they would otherwise create inside the shop.
James Hamilton (or “Stumpy Nubs”) is a self-taught tool expert, engineer, writer, teacher and video producer. In 2008 he went into woodworking full time, creating a weekly Internet woodworking show that focused on the workshop itself. Now, Stumpy Nubs Woodworking has grown into one of the most popular multi-media woodworking resources in the industry.
Use this model whether you’re looking to turn your team of one into a two-person shop or you’re hoping to build out your marketing department to a team of 10 or more.  By focusing on the skill sets your business needs to be successful — rather than on the resume of an individual candidate — you’ll ensure vital functions are covered while expanding in a sustainable way.
You know I can remember my very first workshop, and the very first power tool I ever bought when I was nine years old. Well, I have still have it, doesn’t work anymore but it lasted for 20 years, and I bought it from a mail order catalog for $11.41. I’ve held onto it all these years, because I knew I would find some special place sooner or later that it needs to rest. Well here’s a nice spot right here, I think that’s where it’ll end up.
If you have some experience under your belt, put it to good use as a life or career coach. Many of us are looking for guidance in our careers -- and finding someone with the time to mentor us can be tough. Life/career coaches don’t come cheap, but they are able to offer clients the intense and hands-on training and advice they need to make serious moves in their personal and professional lives. After all, sometimes everyone just needs some uplifting advice.
Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).
The idea of not having your own bathroom nearby can be incredibly intimidating, but we’ve found that this is actually one of the easiest parts of vanlife. Public restrooms are plentiful throughout North America, and we’ve never not had a bathroom when we needed one. Gas stations, truck stops, Walmarts, McDonald’s - you name it, we’ve done some business there.
So keep this in mind when choosing fixtures and display units: The ultimate purpose of fixtures and display units is to put your products front-and-center. But at the same time, the overall look, styling, and finish is your biggest branding opportunity. Choose cohesive fixtures and display pieces that coordinate with your product collections but don’t overpower them, like the successful looks below:

So what does all this boil down to? I favour starting with a good workbench and top quality hand tools – chisels, a couple of planes, a hammer, a few Japanese handsaws – stuff like that. You’ll be amazed at what you can accomplish when properly equipped. Build simple items at first, and then add the very best power tools you can – as you can afford to – in the order that makes the most sense for the work you’re interested in. Yes, this gets you off to a slower start, but what’s the rush? You’ll soon surpass the ‘buy-it-all-at-once’ folks who end up struggling with beginner tools that hold them back from getting better.


Do you have 3 goals left? Great! That's the perfect number. Do you have more? That's okay as well. If you have more time to work on your business, then you may be able to accomplish more then 3. But it also depends on the type of goal you are trying to accomplish. I just recommend not trying to over achieve in fear of not accomplishing everything you set out to do. 
If you don’t have the time (or interest!) in building your own conversion but you still want to give van life a test drive, we’ve got an idea for you! We’d recommend getting a rental vehicle from Escape Campervans. They have 10 different locations across North America and come fully loaded with all the gear you need for an epic road trip. Plus, their rates are fair and affordable.
In a small space, there's not much room for one-trick ponies: You need gear that can do many different things, and that goes for your work space and stands, too. You can add a wood clamp to a multifunction workbench, but you probably need compact work or tool-holding stands to make up for the lack of a large work surface. Occasionally you may need to take your work to another room or even outside, in which case portability is also important.

A loop floor plan, sometimes called a racetrack layout, creates the most guided shopping experience of the three. A loop store layout features a defined pathway throughout the store, which exposes customers to every item on display. Bed, Bath & Beyond stores are good examples of a loop floor plan. Loop floor plans work very well with zone merchandising tactics, too, which we discuss in detail below.
Stop schlepping extensions cords across your garage floor. Make sure your workshop has enough power outlets to charge your tool batteries as well as power your corded shop tools. Your drill press or band saw shouldn’t compete for outlets with a charging drill battery, and you shouldn’t risk tripping over a cable that’s laid across your garage floor.
As the old saying goes, the only two inevitable things in life are death and taxes. Almost all small businesses in the United States are subject to some form of corporate income or gross receipts tax on a state level — that is, unless you happen to be a lucky inhabitant of the great states of Wyoming, Nevada or South Dakota. Actually, even these states will require you to pay state workers' compensation insurance and unemployment insurance taxes. Oh, and of course every small business in the country is subject to some form of federal taxation.
Next up are the chisels, you can start with a couple of sizes and build from there. When looking at saws, for joinery a dovetail saw is a good place to start, with a choice between western style or Japanese. For precise cuts across the grain, cutting tenon shoulders, and defining the edges of a dado a carcass saw also makes a good complement to the dovetail saw.
To make the most of your workshop oasis, look for a water dispenser that offers a choice between chilled and hot water. This will let you enjoy a cold, refreshing drink in the heat of summer rather than a lukewarm bottle that’s been sitting around gathering dust. You’ll also cut down on the amount of plastic your household goes through, which is a boon for the environment. In the winter, the hot water tap will also you to make a cup of tea or a mug of instant coffee on the spot. No matter what your taste, a versatile drink dispenser will keep you hydrated and happy while you work.

Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.
Ok Rob let me try again .I would suggest you sign up for a community collage woodworking class or a woodworking coop where you can use the tools you will need to build the kind of items you have in mind. You say you have used the tools you listed but that could mean only used them once or twice. If you have minimal experience with tools and woodworking that might be another reason to take a class assuming there is one available . Do you have a space you can use as a shop ,a garage,carport etc? As far as tools and equipment are concerned I think Knotscott covered it very well. I know your supposed’s said you couldn’t find tools on Craigslist or garage sales but those might be the place you can make an offer on a shop full of tools in the price range you trying to stay in possibly with some materials and other extras. It might even work to put a wanted wood shop full of tools in the tools section of your local Craigslist.

I have a question, you mention what a problem it would be if the cinder blocks were to sink yet you have installed them with the least amount of footprint on the ground. Was there a reason for this? I would have installed them with the flat side on the ground, and I realize they would not hold as much load as the way you have them but considering the number you have used, the spacing, and the size of the shed, load should not be a problem. Just wondering.
Let’s face it, one of the most significant costs of your shop will be its foundation. While you’re at it, what about adding space above your shop? There may be regulations preventing you from building living space above your shop if it is in an urban setting or in an outbuilding, but there may be some flex­ibility depending on where you live. It is in the municipality’s interests to encourage infill housing that uses existing infra­structure. At a minimum, think about including attic trusses to create some space above your shop for drying lumber or storing equipment. Access could be from simple pull-down attic stairs or from the exterior if you don’t want to lose floor space to a stair or ladder. If you’re creating an addition to your house, you may be able to add a couple of rooms you’ve always wanted, such as a family room, office or in-law suite.
However, instead of sharing a remodel update this week I thought I would do something a little different. This little voice in my head (sometimes called my husband) has been nagging me to add videos to my blog. I did a couple 1 minute hands-only videos a few months back, but I have been seriously afraid to get in front of the camera. The nagging voice finally won out and I bit the bullet and got in front of the camera for you today! I decided to do a video for today’s post instead of just writing out a boring list. And while editing the video I came to the realization that I am very expressive when I talk. Wow! I use my whole face when I talk. I guess that’s what people meant when they said I am dramatic. Oh well, this is me so I hope you enjoy today’s video about how to build a woodshop on a budget.
If you want that homey cabin feel inside your van, then lining the walls and/or ceiling with tongue-and-groove paneling is a good choice. Paneling looks awesome - the cedar paneling on our ceiling is one of the defining features of our van. And we cut ours to random lengths and stained it several colors to really give it that mismatched, rustic look.
It all depends on what you care about most. Putting your kitchen by the side door could simplify refilling your water and propane tanks. Putting it behind the driver’s seat creates a nice, open feel in your van. Right behind the cab makes your van more private, while all the way in the back is a different twist on most van layouts out there. Some vanlifers even have kitchens that pull out of the trunk on drawers for cooking outside.
I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.
The tablesaw—This tool is the backbone of nearly every shop, and for good reason. It allows unmatched precision in ripping parallel edges and crosscutting at a variety of angles. Most woodworkers find it crucial for the basic milling of stock. It is also suited to many joinery tasks, easily producing tenons, box joints, and—with a reground blade—the tails for dovetail joints.
The standard option for a shop floor is a concrete slab. You’re probably not going to go to the trouble of creating a basement beneath your shop, although it is possible. The weight of most woodworking machines suggests that a con­crete floor is the most solid and durable substrate available. It has the potential to be used as thermal mass to store heat from your heating system or from the sun, but it can be tiring and hard on your body to be standing on concrete all the time. You can add a vapour barrier, 2x4 sleepers and a wooden floor above the concrete to ease the tendency of the floor to strain your feet and back, or you can add anti-fatigue mats in key areas where you’ll be standing for longer periods.
So after 14 years in our previous location, my company moved to a new shop last month. My shop went from 1600sqft split into 2 bays with the kitchen in between to a contiguous 2950 sqft. Still don't know why the the office portion needed to grow by the same percentage when there were already 10 empty cubes at the old office, but thats an argument for another day. The boss got his 500 sqft office so he is happy.
×