Calculating the size of your desired parking lot is easy. The rule of thumb is to have a parking spot for every three customers. Determining traffic is trickier and potentially more lucrative. To help, we wrote an article on how to calculate your desired foot traffic. If you want to calculate your desired vehicle traffic, you can refer to our article on how to choose a location for your restaurant.
Now, this is kind of an odd situation here, a few years ago when we bought this building there was a concrete block wall around here and a large drain right in the middle of the floor. Well the drain will certainly come in handy for any cleanup in the shop but the walls kind of left us when we removed those kind of left us a little divot and a little bit of damage here, so to make this nice and smooth so that our rolling workbenches will roll around real nicely we’re having to do a good bit of floor patch.
These basics are going to set you back about $180, leaving you with $320 left to work with. We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives. This should lead to more consistent results, more enjoyable builds, and increased efficiency. These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
Remember that you must allow three feet of pathway space between all display units to meet Americans with Disabilities Act (ADA) requirements. But customer comfort is more than a requirement. Studies have proven, time and time again, that customers do not like to be jostled when shopping. Allow generous pathways between fixtures. Experts recommend three feet, six inches, so customers can move freely, examine products, and carry items to your registers. This will keep customers happily browsing in your store and you in good standing with the ADA.
Pegboard panels like this are extremely popular way to display and store hand tools. But they have one annoying problem is that when you lift off a tool, often the hook itself will pop out of the board. And that happens with over a number of times, every time you reach for a tool it can get pretty annoying. So you can buy at the hardware store, they make straps and special devices to hold the hook in place, but I’ve found this works just as well and it’s a lot cheaper.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
Do you create, collect, or curate anything special? Consider starting an ecommerce store and turning your hobby into a full-time job. Whether you need somewhere to sell all that pottery you’ve been making, or an excuse to search for the sports memorabilia you love tracking down -- an ecommerce store can make it financially viable for you to pursue your passion.
Sprinter vans have been around for awhile, but they’re still the new kid on the block. These vans are especially known for their interior height, long wheelbase, and boxier shape - making them ideal for building out a spacious, functional living space. This category includes the original Mercedes/Dodge Sprinters, as well as Ford Transits and Dodge Promasters (check out this article and this helpful graphic for more information on the differences between these).
After years of digging down under router tables, lifting the entire unit up to change bits, and then fighting to get the plate flush again in the table, I chose to spend the money to purchase a router table, fence, and lift system. I did a thorough review of these systems, and chose the Canadian made Jessem Rout-R-Lift II kit. The system comes with a solid steel stand, a phenolic table, an adjustable extruded aluminum fence, and their base model lift system. For budget reasons, I did not choose the hefty Mast-R-Lift, but I am quite happy with the lighter Rout-R-Lift II. It will last me a couple of lifetimes, so it is the right system at the right price for me in my one-man shop. Hats off to Jessem for making a great lift at a very reasonable price in the middle of a tough economy. The table is durable, and flat. The direct drive lift is smooth and precise. I mated the lift system to a mid-sized model 690 Porter Cable router, which has a fixed speed, and enough power to do anything I need. The Jessem system uses a bayonet type mount for the table inserts, a nice touch that makes swapping the table insert quick and simple. As with all my machines, the router table is connected with the supplied dust port to my shop dust collection system with automated switching.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts.
Household vacs are not designed to handle large quantities of sawdust or wood chips. Their filters clog up quickly, greatly reducing suction. While you can get away with using a small cordless vacuum for small messes, a shop vacuum offers greater power and capacity. Whether you already own a shop vacuum or are shopping for your first, consider purchasing disposable bags or a washable and reusable CleanStream filter.
When Julie Owen bought Cocobolo Interiors in 2008, she set about adding more contemporary items to the Armonk, N.Y., shop. But with only 3,000 square feet, she struggled to figure out where to put her expanding line of furniture, lighting fixtures and accessories. Her solution: create sections within the shop and arrange the furniture the way customers might imagine it at home, using low bookcases and folding screens as dividers.
When it does come time to choose a long-term space and negotiate a deal, it’s important to remember that there is more to discuss than just the monthly rental rate. Subjects you’ll want to raise include the proposed length of your lease and options for renewal, responsibility for ongoing maintenance and repairs, payment of utilities, and obligations around property insurance. Parking rights are also essential for many, especially businesses located in a small shopping center.
Chris Marshall: You’re asking a question that would take many magazine articles or a whole chapter of a good shop-design book to answer adequately. If you haven’t already done so, you might also want to ask this question to the good folks that frequent our forum on woodworking.com. Every woodworker with a shop will have a slightly different answer, so here’s mine. I’ve never had a brick shop, but my last one was a metal pole barn (30 ft. x 40 ft.). I outfitted the interior with 2×6-framed walls and plenty of insulation. It stayed reasonably cool in the summer and warm in the winter, using a wall air conditioner and a 60,000 BTU furnace. Currently, I have a 24 ft. x 42 ft. garage space for my shop. It is framed conventionally with 2×6 walls and stick-built 2×10 rafters. I’ve only been in my new shop for about a year, but it is working just as well or better than my pole barn did, because the new shop has many large windows that let in lots more natural light. I’ve used 8-ft. fluorescent T8 light fixtures in both buildings with good success, and I ran both 110- and 220-volt outlets all around the room. The last shop had a plywood floor; the current one, a concrete slab. I thought I would notice a bigger difference between the two flooring types, in terms of how tired it makes my legs by the end of the day. But in all honesty, a good pair of supportive shoes seems to make the difference moot for me. Both types of buildings benefit from a dehumidifier during humid months (when I’m not running the A/C, that is) to keep the relative humidity low and my tools rust-free. If all things were equal, and money were no object, I would probably go with a conventionally framed wood building over the pole barn. It was easier to build that from scratch as opposed to retrofitting the pole barn framing with walls afterward. But, as I say, the next woodworker will probably offer you a completely different answer from mine. Good luck in your decision!
I set an initial budget of $10,000 to build the shop – everything from studs and drywall to hand tools and machinery. The final number was over by $1,000, but I’m still very happy with the result. The shop is now my haven, with a good sound system and good lighting. Every time I go back into the shop, it is exactly the way I left it, because it is my shop!
A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.
BEST ANSWER: Hi, I probably can't help, depending on where you are in the process. If the bench in the photo looks like it's just what you need, you should download the plan. I think Rockler has several ready to assemble benches that look quite good. Example: Large Workbench (N2000) Item #: 31719... I. too, am retired and trying to decide whether to buy or build. I have a bench that looks good and works good, but just is too light for hand work. It all depends on what you expect to be using the bench for. There are some good books out there to help us decide. "The Workbench" by Lon Schleining" is excellent. Also, Christopher Schwarz has written several good books on the subject. Vince, good luck and have fun working wood.
In all you can spend under $1,000 and be setup in a great workshop. But I know how it feels when you’re shopping for new tools… and you think… “why not buy the top of the line so it lasts longer”… or “may as well get the best while I’m spending money”… those kinds of thoughts won’t only get you into big trouble with your other half… it’s also COMPLETELY wrong.
Planning your store layout is no small task, but many small retail store owners do it all themselves with great success. So why not you? Take it slow, follow our seven steps, and remember to put the customer first. With the ideas in this guide and a little elbow grease, you’ll soon be on your way to mapping out a retail store that’s easy to navigate, welcoming to customers, and best of all—profitable.
We’ve been focused on the first category so far, but there is also an allure to buying an existing business. These enterprises will often come with brand awareness, a customer base, trained employees, an established supply chain, and most importantly (we hope), demonstrated profitability. As a result, countless startup risks can be diminished by taking this route. That is only true, however, if you make sure to carry out thorough due diligence on the existing business.
2. Just the basics—I’ve used a compound miter saw, circular saw, jigsaw, band saw, router, table saw, drill, finishing sander, belt sander, Dremel, oscillating multi-tool, bar clamps, and a Shop-Vac. I haven’t used a planer, jointer, or lathe. I’ve never owned a table saw but have used a circular saw or improvised with a router for a few long cuts.
Back in the 1970s and treeplanting in Oregon, I and Tony Lessa lived for two weeks at a time in the back of my 1954 Chevy PU. The canopy was just a simple shell with the board across next to the cab. After the fourth or fifth trip out in the season the accumulated funk was too much. You can imagine two hard-working guys in very muddy and cold conditions coming in after work with dirty wet gear. Pretty desperate circumstances but before Reagan trashed the treeplanting industry our coop ( Hoedads & then Second Growth) was making good money so we endured the hardships. It works for the young. Now, at 76, I find sleeping two of us between the wheel wells in a Dodge G. Caravan (seats removed) much too crowded. I think I will tent and the wife can have the van.
I look at these workshops and wonder if I'm the only woodworker that has other hobbies that require shop space. My one car garage serves for woodworking, motorcycle storage and maintenance and home repairs. I have a floor standing drill press, Band Saw, 10" cabinet saw, lathe, 6" jointer, 3 tier tool chest(automotive tools only) 4' workbench, mortiser on a pedistal, grinder on a 16" square storage cabinet, and a roll around 40"x22" cabinet that hold my miter saw, portable thickness planer and other storage. Luckily I have an attached shed where I can keep my dust collector and compressor and have them plumbed into the shop. Right now my snow blower also resides in the shop where otherwise my 450cc KTM off road motorcycle would. I need to step outside in order to change my mind so please stop teasing me with these to die for shops. Paul
Like most things in life, we believe that entrepreneurship can be learned, you just have to be willing to put one foot in front of the other. Aftering reading How to Start a Small Business 101, you’ll be equipped with the essential tools and resources you need to succeed at planning, raising capital, and executing crucial day-to-day business operations.
Location, location, location is quoted so often for a reason. When starting a small business, the wrong choice could hurt your business before you’ve even had the chance to open the doors. Take the time to really understand your customers and do everything you can to gather real world insights that will help you determine the viability of your potential new space.
2) I haven’t spent very many nights in full on winter conditions (that 12 degree night in Boise comes to mind!), so I can’t comment too much. It was fine for that… Mostly it was hard transitioning from the warmth of the cab to the frigid air while you are shifting things around and getting ready for bed, but then once you were inside the canopy it was fine. Lots of frosty ice on the inside windows, but in my sleeping bag all was well. It stays a little warmer in the canopy. Maybe I’m a wuss, but I didn’t want to spend an extended period of time dirtbagging it in my truck while I was ice climbing (I spent the first two months in Ouray, CO, sharing a rental), I just thought it would be too challenging/miserable to dry and manage gear in a confined space with the shorter daylight hours. I’d be perfectly content doing future weekend trips with this setup though!
By building your own workshop machines and jigs, you can create customized tools that include all of your favorite and much-needed features for less than half the cost of commercial tools (plus, get bragging rights for having the coolest woodworking shop in town). All you will need is a drill press, table saw, some common tools, and patience. Then, you can start following these step-by-step instructions to create homemade machines such as a sliding-top router table, jigsaw, downdraft dust collection table, a 24” band saw and more!
We don't have a Dometic CFX-50 in our van, but we wish we had gotten one for our build. This is a great little fridge that many vanlifers happily own. It’s rugged and durable, and it keeps your food cold for less money than many of the other fridges out there. It also has a nifty side-open lid, which makes it a lot easier to open with a lower clearance.