While you have a decent starter shop, it's important to keep in mind the projects that your tools can handle.  You are going to want to focus on projects that don't require your stock to be ripped to a different dimensions than what you purchased it at.  You are currently only set up to do crosscuts with your miter saw.  So while you can turn an 8' 2x4 into two 4' 2x4s, your not going to be able to turn that same board into two 2x2s.    

However, instead of sharing a remodel update this week I thought I would do something a little different. This little voice in my head (sometimes called my husband) has been nagging me to add videos to my blog. I did a couple 1 minute hands-only videos a few months back, but I have been seriously afraid to get in front of the camera. The nagging voice finally won out and I bit the bullet and got in front of the camera for you today! I decided to do a video for today’s post instead of just writing out a boring list. And while editing the video I came to the realization that I am very expressive when I talk. Wow! I use my whole face when I talk. I guess that’s what people meant when they said I am dramatic. Oh well, this is me so I hope you enjoy today’s video about how to build a woodshop on a budget.
My wife and I have just bought a block and will be building a new house – as part of this will be the building of the “shed” – which is really a workshop as I am a very keen Woodworker (I have most of the toys!!). My question is – Leaving money aside “Is a brick or metal shed better – especially in regards to moisture, inside temperature (heating and cooling), noise etc”? Any other suggestions would also be appreciated – eg lining the structure, power needs, lighting, etc. I appreciate your expert opinion. – Ivan Banks
If you want that homey cabin feel inside your van, then lining the walls and/or ceiling with tongue-and-groove paneling is a good choice. Paneling looks awesome - the cedar paneling on our ceiling is one of the defining features of our van. And we cut ours to random lengths and stained it several colors to really give it that mismatched, rustic look.
Many DIY campervans have kitchen units that are directly behind the cab, sealing it off from the rest of the van. These layouts offer increased privacy and stealthiness, especially if you completely wall off the cab, and open up some space in the back of the van. This layout can be paired with a lengthwise bed, fixed bed, or convertible dinette bed. You can also place your propane and water connections right by the door, making refill easier.

Hey Melody, thanks for the email. I’ve traveled through some extremely humid areas (Central America)… I’m taking it that your canopy does not have a headliner? That in and of itself helps a great deal. Personally I would be hesitant to put holes or van roof vents in my cap, but that may be what you want to do. I would try sleeping with a portable personal fan first and see how that helps with the condensation issue. For me it worked wonders while sleeping in those hot and humid environments. I ran mine off the inverter connected to my secondary battery.
I will also typically secure those sorts of items under my locked platform if I am gone for a few days in the backcountry, because in reality I could probably care less if someone broke in and stole my box of food, versus someone who stole my clothes or expensive down jackets, which would be much more problematic (and costly) to replace on the road.
However, instead of sharing a remodel update this week I thought I would do something a little different. This little voice in my head (sometimes called my husband) has been nagging me to add videos to my blog. I did a couple 1 minute hands-only videos a few months back, but I have been seriously afraid to get in front of the camera. The nagging voice finally won out and I bit the bullet and got in front of the camera for you today! I decided to do a video for today’s post instead of just writing out a boring list. And while editing the video I came to the realization that I am very expressive when I talk. Wow! I use my whole face when I talk. I guess that’s what people meant when they said I am dramatic. Oh well, this is me so I hope you enjoy today’s video about how to build a woodshop on a budget.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.

For those of us building apps, there's an increasingly larger burden on us to meet the expectations of our users. We've outlined the considerations of what makes a great app in the past, which are more relevant than ever. Users simply don't have the patience for apps that are overly complex, slow, or buggy. The best apps are personalized, highly contextualized, and touch human emotion. Meeting those user expectations is significantly challenging.
You may not have heard of Lemonade Freedom. It’s an organization set up after a spate of children’s lemonade stand closures by police who decided to take an absurdly heavy-handed approach to permit enforcement (you can read more about it in Forbes). Apparently the kids involved hadn’t applied for the necessary paperwork to run their stands. In one example in Georgia, three kids saving for a trip to their local water park had their endeavor closed down because they lacked the business license, peddler's permit, and food handler's license. Crazy? Only mostly.
Hey, I hope we’ve been able to share with you some ideas that you can use if you’re thinking about building a workshop or any type of hobby room or just about any room in your house that you can get this kind of enjoyment out of. We have a lot more details on this shop as well as other things you need to consider if you’re building a shop on our website at todayshomeowner.com. hey thanks for being with us.
Congratulations on your new shop and all your success. I’ve watched all of your videos and someday if I have the money I would love to join your guild. I started a small workshop in my grandparents basement and someday I hope to start a small bussiness. Your website and videos have been the most informative and the most inspirational to me as a beginning woodworker. Thank you for sharing all your tips and hard work with people like me. I look forward to watching your videos for years to come.
This will be a personal matter, depend­ing on whether it will be helpful for finishing or sharpening. However, it is a good idea to look beyond your current use of this space to the next owner. Would it be beneficial to add plumbing hookups so that the shop could someday be an apart­ment, or an art studio, or an extension to your house? It could add to the resale value of your house to be able to create as flexible an area as possible by roughing in a bathroom and even a kitchenette area if you can. If this is done when wall cavities are open or before the slab is poured, your forethought could pay dividends but not cost much up front. 
Woodworking isn’t just an overnight hobby, for most it’s a fun pursuit that lasts a lifetime. As your skills develop, the workshop becomes a place not just to build but to repair along the way. In a world where people are strongly influenced by consumerism, there’s a tendency to revert to a throwaway culture. But if you can fix before throwing away, then your tools start to make a return on their investment and have a bigger impact.
Many small business owners start on a shoestring budget, intertwining their personal and business finances, supporting the business with their personal credit cards, accepting payments into their personal checking account, and even submitting tax returns that mix up personal and business finances. While this is common, it can create tax headaches, make bookkeeping more time consuming, and, most importantly, can also interfere with the proper evaluation of your business.
Disclaimer: We spend hours researching and writing our articles and strive to provide accurate, up-to-date content. However, our research is meant to aid your own, and we are not acting as licensed professionals. We recommend that you consult with your own lawyer, accountant, or other licensed professional for relevant business decisions. Click here to see our full disclaimer.
​One tool that has been notably missing from the earlier builds is a router.  There are so many reasons to own a router that I am not going to even try to list them.  But if you want to get the creative juices flowing, take a look at this Pinterest page.   The important thing to know is that this versatile tool can help you accomplish a number of tasks, everything from finishing edges to cutting dove tails.  

The key to success here is having clear processes written down, promoting from within whenever possible, and remaining open to change. You’ll want to balance your desire to educate your manager on how to manage your business with an openness to feedback and new ways of doing things. You’ll also want to take advantage of the technology available to keep you abreast of things like real-time sales data for all your locations, no matter where you are.


A not for compensation nonexclusive arrangement, on the other hand, gives a tenant maximum flexibility. It’s nonbinding and there are no commissions negotiated. Instead, it gives the broker the right to speak on your behalf and schedule listings for you to see. However, while it provides flexibility, this arrangement gives the tenant broker less of a fiduciary duty.

By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.

You can also make your store comfortable by incorporating a waiting area with comfy seats and benches to encourage customers to spend more time in your store. This is especially helpful for shoppers accompanied by someone who isn't interested in making a purchase. But keep the seats or benches facing the merchandise so that they're still top of mind for those lounging around in your store.  
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.
Well, I thought about that I don’t want all that dust to kind of infiltrate everything else in the building. So actually instead of putting in some kind of dust collection system, I thought that I would probably just put a nice shop vac here. And then I have room that I can bring some hose back behind this column and then you know if you’re sitting here working on something we can have adapters that go right into a miter saw or right into a sander or have a little outlet more or less to lay up on the counter that would collect all of the dust. And the same thing could happen on any of the work we do out here.

When you’re first starting out, it can be hard to imagine that there are entrepreneurs out there complaining of having grown too fast. But for some, it’s not a problem that’s welcome. For every Ben and Jerry’s, (Ben Cohen and Jerry Greenfield turned a rundown Burlington, VT gas station into an ice cream empire), there’s a Zynga or a Living Social that has enjoyed incredibly fast-paced growth, let their operating costs get out of hand, and then had to engage in mass layoffs when reality hit. If you’re enjoying fast-paced growth, make sure that this is reflected in your operating margins, not just the metric of revenue. You don’t want to be the butt of the old retail joke: “We’re losing a buck on every sale, but we sure are making it up on volume!”
Hi, I have looked through pictures of the shop books. What I am interested in finding is a book with layout design options. I am ready to build a new shop for myself and want to put dust and electrical under the slab. Best layout designs would help me to figure out how to layout a shop that is aprox. 28'x 36'. Is there a book that has this type of information.
I will also typically secure those sorts of items under my locked platform if I am gone for a few days in the backcountry, because in reality I could probably care less if someone broke in and stole my box of food, versus someone who stole my clothes or expensive down jackets, which would be much more problematic (and costly) to replace on the road.
Most businesses must obtain a variety of business licenses, permits, and registrations before opening their doors to the public. As a small business owner, it is your responsibility to ensure that you are abiding all the laws and regulations applicable in your state and to your particular industry. You also have to research and apply for all relevant permits and licenses that apply to your business type and location. Remember, it is impossible to plead ignorance as a defense. It’s up to you to educate yourself. When in doubt leave it to the professionals. CT Corporation offers custom license packages that simplify the process for business owners. Click here for an example of what that looks like.
However, my guess is around $250,00 t0 $300,000. So as you say you will have a good mortgage to pay for. So excuse me for being nosy. I am retired and I have started setting up my shop in my two car garage. It is not insulated just bare walls and open ceiling. I am going to start doing some projects and will keep watching your shows. I was a Computer Engineer and although I liked my job i always had that desire to get back in wood working and now I am doing just that.
If you want to run a business operated by yourself and more than one employee, you may run into zoning issues if your location is zoned for residential use only. It’s common for municipalities to allow and encourage home-based busi­nesses but there will likely be a maximum area that you will be permitted to add for business purposes. If you try to build a shop that will contribute noise and traffic (from employees or deliveries) to an urban neighbourhood, you run the risk of run­ning into opposition from neighbours concerned by the impact your shop will have. Your municipality will have planners with whom you should consult as you begin to define the possibili­ties that your property will allow.
I save all my back issues of The Family Handyman magazine and love the projects and repair tips. The trouble is, I’m not always ready to do the project when the issue arrives. To make my favorite articles easy to find at a later date, I put a stick-on label on the cover and then add notes for easy reference when the time comes to do the job. — Willie Schreiber. Plus: Check out this small workshop storage solution.
Leslie recommends that retailers provide some type of seating for both customers and anyone who is accompanying them. Shoppers do get tired and so do their friends and relatives who are along for the ride. Why not offer them a chair? Seating can be as simple as stools near the checkout or a lounge area near the dressing rooms, like this fun setup below:
Since grid layouts are used in most grocery, big box, and convenience stores, they create a familiar feel to customers. However, due to this familiarity, they tend to impart a grab-and-go experience. A grid layout can be a good choice for small retailers who shelf-stock inventory in quantity, like toys, books, magazines, specialty foods, kitchenware, and home goods. However, it’s not ideal for retailers who want to create an upscale, branded environment that invites relaxed browsing.
Garages are usually dark, which makes setting up task lighting a priority for a productive workspace. Track lighting is an easy option to install and gives your some directional overhead lighting, but it can cast shadows (especially if the light source is behind you while you work) and you’ll need another lighting source for task and overall room illumination. A simple, adjustable work lamp is helpful for soldering or when you need bright focused lighting.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
State Parks/Developed Campgrounds. Every once in awhile, it’s kind of nice to stay at a state park or other developed campground - and a big reason why is that they have showers (and sometimes laundry, too). This is what we’ve done most often when we need a shower on the road. Many state parks also have small day use fees if you don’t want to actually camp there.
Ultimate Small Shop Ultimate Small Shop Review Ultimate Small Shop Pdf Ultimate Small Shop Guide Woodworking Ultimate Small Shop Guide Ultimate Small Shop Book Ultimate Small Shop woodworking Ralph Chapman Ultimate Small Shop Ultimate Small Garage Clock Shop Ultimate Small Shop Woodworking Ultimate Small Shop Reviews Ultimate Small Shop program Ultimate Small Shop eBook Ultimate Small Shop Ebook Download Ultimate Small Shop discount Ultimate Small Shop Tips Ultimate Small Shop Videos Ultimate Small Shop Pdf Download Ultimate Small Shop Download Ultimate Small Shop PDF download by Debra Aros Ultimate Small Shop Ebook Free Ultimate Small Shop Free Ultimate Small Shop Legit Ultimate Small Shop Result Ultimate Small Shop Member Ultimate Small Shop Meal Plan Ultimate Small Shop Online Review Ultimate Small Shop does it really work Ultimate Small Shop Guide Download Ultimate Small Shop YouTube Ultimate Small Shop Free Pdf Download
You can see in this step how I notched each rafter to fit more securely to the walls.  I also used a metal hurricane strap to secure each rafter to the wall.  Even though this was not required by code, I felt my tools were far to valuable to be left to chance over such an inexpensive solution.  The walls are a simple board and batten system.  The 1x3 trim covers the joints of the 4x8 OSB.  They make much more high quality sheets goods to use as siding.  However, the cheapest I found was $35 a sheet and the OSB was about $5 a sheet.  I sealed the OSB and painted it with exterior paint.  If I run into problems in the future, I can just add a second layer of more durable material or simply have siding installed.  It has held up very well over the past couple years and I see no need to spend more money on it now.
You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.

This is a fundamental question. A good place to start is with a survey of your property. Most municipalities have a maximum percentage of your lot that you can build on and standard setbacks from your property lines that you will need to adhere to without needing to request special permission to build. On a photocopy of your survey you can draw in what your local setbacks are in order to define the location within which you will be permitted to build. In a best-case scenario, you will have the space to build without compromising too much on space or location; otherwise, you may need to request a minor variance, which would allow you to circumvent an obsta­cle such as a setback.

To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.
So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.
Hey Joe, I just hit 178k on my truck. I remember when I started out the first time around it had like 144k or so. They are known to go quite far, so we’ll see how it goes. Maintenance on the road… I just stop at those oil lube places for the most part, and do regular weekly checks under the hood for fluid levels, etc. I’m not too mechanically inclined!
One of the things that draws me to the online woodworking community is amount of passion people show are willing to share. Your shop build is a fine example of your willingness to let us in on your passion. You could have said “I’ll be back in a few months when its done” and most of us would have waited but instead you turned it in to a summer of updates and dream shop discussion. Thanks!
Well this is the same unit I have used for years so the noise level will be what it has been. I never turn it on without ear protection. In the future, I plan on building a little closet around the cyclone to help mitigate the noise to some extent. As for cycling the motor, I read that too. But the way I work, I just can’t do that. I have to turn it on and off as needed but I do try to limit it as much as possible by doing all of my heavy milling at once.

Do you carry items that bring your customers back time and time again? Consider placing these primary and similar secondary product lines toward the back of your store. Or, if your stock is constantly changing and you don’t carry replenishing goods, place your sale items toward the back. That way, customers must pass your new items and promotional displays on their way to check out the deals in back.
Let’s face it, one of the most significant costs of your shop will be its foundation. While you’re at it, what about adding space above your shop? There may be regulations preventing you from building living space above your shop if it is in an urban setting or in an outbuilding, but there may be some flex­ibility depending on where you live. It is in the municipality’s interests to encourage infill housing that uses existing infra­structure. At a minimum, think about including attic trusses to create some space above your shop for drying lumber or storing equipment. Access could be from simple pull-down attic stairs or from the exterior if you don’t want to lose floor space to a stair or ladder. If you’re creating an addition to your house, you may be able to add a couple of rooms you’ve always wanted, such as a family room, office or in-law suite.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
There are certain sayings that hold true and when buying clamps and measuring equipment parting with cash for quality make sense. But which clamps? G, F, sash, spring or strap? There are so many clamps and measuring tools available. Let the project decide which ones you need. As a reassurance, our Axminster Trade Clamps come with a lifetime guarantee, so this is one investment that literally lasts that long.

One thing I found while looking on the topper websites is a piece of weather strip designed to go between the tailgate and the truck bed. It has a special wedge shape to it so when you close the tailgate it makes a watertight seal. It is just the thing to keep the dust and dirt from entering the back of your rig when driving down the dirt roads. They’re inexpensive too, for a full size truck like my Dodge it’s only $25. It has adhesive on one side, so installation looks simple.
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.
I used to keep screws in a cof- fee can, but when I reached in with my hand, the screw points pricked my fingers. The can was also a dust and dirt depot. I bought a clear water bottle with a pop-up lid and poured screws into the bottle with a funnel. The screws stay clean, and I can shake them out of the bottle one at a time. — Bruce Burley. Hardware Storage: DIY Tips and Hints
With all the time and effort you've put into properly merchandising your products, the last thing you want is for incoming customers to hurry past them — this ultimately limits the number of products they'll purchase. One way retailers combat this is through creating breaks that force them to pause. These are sometimes referred to as "speed bumps." Essentially, this can be anything that gives customers a visual break and can be achieved through signage or special/seasonal displays.
The enormous range and affordability of options has provided the chance for small business owners to apply technology to their accounting, marketing, and day-to-day operations. You can spend less money, save valuable time, and gather data about almost every aspect of your business. What’s more, you can enhance the way your customers experience your store in a meaningful and cost-effective way.
It does sag a little bit, but not worryingly so. As I mentioned, it often rests on top of the large plastic boxes I place underneath, and I put in a small wooden brace at the entrance. You could definitely build it slightly smaller, or put in a more substantive center brace — like a sheet of plywood that fits into the groove of the bed liner and is the exact height you want.
At $300, the saw is expensive, but it is one of the more affordable saws that offer a 12 inch blade and a double bevel.  The double bevel allows you to adjust both the angle at which the blade cuts into the wood and the tilt of the blade relative to the workpiece.  Having control over both angles allows much easier cuts of trims and moldings.  It's one of those features that you won't use with every project - but when you do need it, you'll be glad you have it

Because workshops are rough and tumble places, the right fan for the job will have an industrial-strength motor and adjustable fan speeds. Easy-to-clean metal blades and a fully encased motor housing are also important features, especially if your shop tends to fill up with sawdust, wood chips and other fine debris. That extra layer of protection will help the fan motor last for years instead of being damaged by particulates.
The issue with the old shop was manufacturing capacity and layout. We get runs of 4 to 6 of the frames on the left in the last pic and sometimes frames twice that size. We were masters of having everything on wheels, which works for a while but it takes twice as long to build anything that way. Then the office ladies walk through the shop to the kitchen while you are grinding and complain about all the dust etc.

Since the summer of 2013, first time visitors to New York City restaurants have been greeted by window signs boasting a large, capitalized A, B or C. These letters reflect the rating given to each restaurant by the New York City Department of Health and Mental Hygiene (NYCDOHMH). Does the need for government oversight of this industry create an additional administrative and financial burden for the businesses in question? Yes it does. Does the rating system also inform consumers and encourage higher food safety standards across the board? Undoubtedly.

In as much as I am a clamp freak, I needed some way to organize clamps without spending a mint on brackets. In our previous house we had a number of glass shelves –which I didn’t plan to put up here. But, the brackets were great – I laid in two tracks next to each other, then took a pair of the shelf brackets, cut a piece of 9/16 x 9/16 x 3 inch pieces of wood – put the wood between the brackets, shrunk wrapped around the brackets and wood, and came up with some really stable clamp hangers.


When I built my shop I opted to buy a much higher quality miter saw and table saw than I truly needed at the time.  It ate up a ton of my budget and forced me to put off adding the tools that would allow me to buy cheaper stock for 2-3 years.  During that time my savings buying rough cut lumber would have probably paid for the upgraded equipment I started out with.  
Great website! I spent a summer living out of a ford focus hatchback while road tripping around the United States. The rear seats were replaced with a small platform to store gear and the rear windows were tinted. I enjoyed the freedom that anywhere I parked no one would see me hop from the drivers seat to my platform for some zzz’s. Also no one would guess that someone is sleeping in a 3dr ford focus.

Every shop should have good lighting, whether natural or artificial. My video work dictates limited natural light, so I was sure to have plenty of overhead T8 fixtures (6500k). You’ll hear me mention in the video that I was disappointed to see that the ends of the shop were just a little dark. Thankfully, I was able to get the contractor to come back in and drop in 4 more fixtures for me, two at either end. Now the light is bright, crisp, and evenly distributed from one side of the shop to the other.


When you’re first starting out, it can be hard to imagine that there are entrepreneurs out there complaining of having grown too fast. But for some, it’s not a problem that’s welcome. For every Ben and Jerry’s, (Ben Cohen and Jerry Greenfield turned a rundown Burlington, VT gas station into an ice cream empire), there’s a Zynga or a Living Social that has enjoyed incredibly fast-paced growth, let their operating costs get out of hand, and then had to engage in mass layoffs when reality hit. If you’re enjoying fast-paced growth, make sure that this is reflected in your operating margins, not just the metric of revenue. You don’t want to be the butt of the old retail joke: “We’re losing a buck on every sale, but we sure are making it up on volume!”
You’ll also want to evaluate your obligation to your employees’ health care provisions following the introduction of the Affordable Care Act, which mandates the responsibility for the cost of insuring full-time employees to businesses with 50 or more full-time, or full-time equivalent employees. It also provides generous tax credits to smaller businesses with 25 or less full-time equivalent employees. Need a little more help understanding how U.S. health insurance reform affects your business? Register for one of the SBA’s upcoming Affordable Care Act webinars. They also offer recordings of previous webinars in both English and Spanish for those who can’t make it to one of their live sessions.

The idea of not having your own bathroom nearby can be incredibly intimidating, but we’ve found that this is actually one of the easiest parts of vanlife. Public restrooms are plentiful throughout North America, and we’ve never not had a bathroom when we needed one. Gas stations, truck stops, Walmarts, McDonald’s - you name it, we’ve done some business there.
We have a 5-gallon clear plastic Hedpak container that our sink drains straight down into. We really like this container because it’s clear, which means we can easily see how full it is. With 5 gallons of gray water capacity, we only need to empty it every 3-4 days. Dumping is easy - just remove the tank from under the sink and pour it out into an RV dump facility or other approved area.

Most workshop tasks require good ventilation, and that’s something garages are generally poor at. Plus, passive ventilation (like opening a window) usually isn’t enough. A ceiling exhaust fan is a good start but if you are serious about keeping things clean then your ultimate workshop should also include a dust collection system, central vacuum and air ventilation system. All three of these systems will keep the dust, dirt, and other heavy particles off your clothes and out of your lungs which makes for a safer work environment.
Some people lean towards starting a small business because they seek freedom, others to fulfill their passions. Some entrepreneurs, however, are driven by a desire to build a legacy, one that that they can hand down to generations to come. Whatever your reasons are for reaching for the stars and aiming for the moon, before you start, remember, there is a dark side.
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.
It can become very difficult and time-consuming to constantly track the amount and purchase price of all your inventory, but it is hugely important to your bottom line. Every time you catch yourself saying, “Sorry, we don’t have that in right now,” you are leading your business in a very unhealthy direction. Not only does being out of something represent a lost sale opportunity, but in a world where consumers place a huge premium on their time, it could mean that you lose that customer forever while hurting your brand reputation in the process.

The on the go mode is ideal for when I’m just driving all day and need to pull over and get some rest, be it in a parking lot, a residential cul-de-suc, or wherever. I usually toss a couple of items in the cab of my truck and crawl into the “coffin” sleeping arrangement for a quick night’s rest, but I can also crawl in without placing anything in the cab.
Hey Anthony, I guess the big question is what part of the country you’ll be sleeping in and what sort of weather you can expect… I would imagine when conditions are fine that a warm sleeping bag would be more than enough (I used to do that before I had a canopy). You’ll just have to worry about rain (snow?) and other inclement weather, but otherwise I don’t know why not. A cheap bivy sack from an army surplus store might be a good addition as well.

At a time when you’re focused on getting in front of customers as quickly and as often as possible, it can be hard to think about official requirements like registering a business name or deciding on a legal structure. Still, now that you have decided to start a small business or buy an existing one, one of the first critical steps is determining the business entity that's right for you.

Also, heard of anyone camping in an Accord sedan? I’m wondering if it’d be worth it to buy a new Tacoma to convert into a dirtbaggin’ vehicle or if I should try to make it in a sedan. Lots of variables… I’ve got the cash but it’d eat into the “cushion” I have for living on the road (about 50% of it). OTOH I could buy a used Tacoma, but they hold value so well it’d seem like long term it’d be best to get it new. I’ve seen some with 250 miles sell for $8,000+. Thoughts on getting a new truck using my beat-up sedan?


Radiation is heat transferred through air or a vacuum- think the heat radiating off of a fire. In a van, the biggest source of radiant heat is your windows. Sunlight (radiant heat) shines in through the windows and heats up the inside of your van. Using a reflective window covering will help deflect radiant heat and keep your van cool. Reflective surfaces also help keep radiant heat inside the van during the winter.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Now that you have your goals mapped out and you know the exact tasks that will help you accomplish them, I want you to pick a day of the week (preferably Monday or Friday) and start planning the week ahead - don’t skip this step, never skip this step. Schedule which one these tasks will happen on what day of the week. So you are literally pulling the tasks from that spreadsheet and placing them into this weekly planner. It’s important to keep in mind deadlines (the ones you set for your goals and when they should be accomplished) and the amount of time it takes you to do a task. You may also want to write down which day it’s due, and who is responsible for this task (if you work with a team).
Garages are usually dark, which makes setting up task lighting a priority for a productive workspace. Track lighting is an easy option to install and gives your some directional overhead lighting, but it can cast shadows (especially if the light source is behind you while you work) and you’ll need another lighting source for task and overall room illumination. A simple, adjustable work lamp is helpful for soldering or when you need bright focused lighting.
I place the band saw first in my order of purchases, because I consider it the heart of the shop. Band saws are very safe tools for ripping, re-sawing, cutting curves and more because all of the force is downward, virtually eliminating any chance of unexpected kickbacks. I wanted a saw that had a strong back, dynamically balanced cast iron wheels for smooth operation and flywheel effect, 12" depth of cut, good dust extraction design, a large table and a solid fence. After shopping around, I settled on the General International Model 90-170 14" saw. It is very smooth, comes with an Excalibur fence, and it is light enough (133kg) to move into your basement without crushing someone.

Nicole and I decided not to go public with the cost of the build. Although we are very open about most things, we are a little uncomfortable about making an expenditure of this magnitude public knowledge. Furthermore, unless you live in the Phoenix area and plan on building the same size shop with the same patio and with all of the same finishing touches and labor requirements, the price isn’t all that helpful to you.


When we published our massive review on how much an app costs back in 2015, we had no idea it would become the top resource on the web. Two years later, that piece is still considered the definitive resource for app development costs in our industry. It’s because of its popularity that I feel compelled to revisit this subject. Additionally, doing so will allow for some fresh perspectives based on what's changed in the app industry as well as another way to look at the topic.
In all you can spend under $1,000 and be setup in a great workshop. But I know how it feels when you’re shopping for new tools… and you think… “why not buy the top of the line so it lasts longer”… or “may as well get the best while I’m spending money”… those kinds of thoughts won’t only get you into big trouble with your other half… it’s also COMPLETELY wrong.
×