Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
I don’t think you have run into this problem, but I have to deal with condensation in the cap as I live in a moist climate. I was thinking of an old van type roof vent with fan for active ventilation, or drilling holes along the side of the cap, inserting short cuts of pipe with fine screens (mozie land), and capping them. This way I could control for rain, cold, etc., but create some passive cross ventilation at roof level.
Some people lean towards starting a small business because they seek freedom, others to fulfill their passions. Some entrepreneurs, however, are driven by a desire to build a legacy, one that that they can hand down to generations to come. Whatever your reasons are for reaching for the stars and aiming for the moon, before you start, remember, there is a dark side.
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
When we published our massive review on how much an app costs back in 2015, we had no idea it would become the top resource on the web. Two years later, that piece is still considered the definitive resource for app development costs in our industry. It’s because of its popularity that I feel compelled to revisit this subject. Additionally, doing so will allow for some fresh perspectives based on what's changed in the app industry as well as another way to look at the topic.
The subfloor provides a stable layer - basically a sheet of plywood - for your floor to sit on. You’ll see a lot of van build videos on Youtube showing a ¾” subfloor, but that thickness just isn’t necessary in a van. The thicker the subfloor, the higher the cost and weight, and the more valuable interior space it takes away. We recommend using ¼” plywood for your subfloor, which is plenty thick enough for a van.
While the recession brought with it a well-documented squeeze on small business lending from banks, there are a number of alternative funding sources available to those who are starting or expanding their small business. Loans and/or equity investments can be sourced from multiple sources, including credit unions, savings and loans, and private financial companies. Family members, friends, and colleagues are also potential avenues to explore.
You might be thinking your business aspirations are too ‘early-stage’ to merit investigating the permits required to run your small business. You’d be wrong. The costs and requirements of staying on the right side of the law should be factored into your initial business plan and ongoing projections. In the long run, this will save you time, money and heartache.
I framed in a 4x8 Garden Shed on the back.  I didn't want it so deep that stuff would get buried in it.  I need to take an updated picture of the back.  These pics were from early on and I have changed some things in the organization.  I used similar framing techniques and built a lean to roof attached with metal hangers.  I chose to use clear corrugated roofing to allow natural light into this shed.  You can see the 2 shopvacs that were originally part of my simple vacuum system.  I have removed them and found that I get better airflow using an electric leaf blower with the vacuum attachment hooked up to my system.  There is a large metal trashcan with a dust collection separator to collect the larger pieces of saw dust and chips.  My air compressor is on a shelf on the right now and I ran a hose through the wall and to a 25 foot reel attached to the ceiling.  I wired separate switched for both on the inside of my shop.  These systems work extremely well for a small shop.  The wall provides some insulation from the overwhelming noise they would otherwise create inside the shop.
Tip: Save money on specialty displays! Many manufacturers offer retailers low-cost or free specialty display fixtures designed to highlight their branded lines, like the one pictured below. These make great speed bump or outpost display units on a tight budget. Your product line reps can tell you if they’re available, plus provide merchandising and display advice.
As the old saying goes, the only two inevitable things in life are death and taxes. Almost all small businesses in the United States are subject to some form of corporate income or gross receipts tax on a state level — that is, unless you happen to be a lucky inhabitant of the great states of Wyoming, Nevada or South Dakota. Actually, even these states will require you to pay state workers' compensation insurance and unemployment insurance taxes. Oh, and of course every small business in the country is subject to some form of federal taxation.

We have Eclipse Sunshades installed on our van. While they’re pricier than the cheap sunshades you’ll find at Walmart, they’re every effective. And since they permanently install on your windshield they’re much more compact - a big plus for living in a van. All we have to do is pull the shades across and velcro them together in the middle and we’re protected from both the sun’s rays and prying eyes.
The right first step online for most stores and restaurants is creating a Google Local Business Listing. Google accounts for 90% of all global organic search traffic and more and more of that traffic is coming from mobile devices. Chances are, your customers are using Google to find you, so you’ll want to make sure your hours, description, contact details, address, and images are all accurate.
It’s no accident that some of the best marketers in the tech startup industry are known as “growth hackers.” Think about your target demographic (e.g. students, local mothers, teenagers) and find any way you can to get the word out to them. Email mommy bloggers, hand out free samples at the local college, or write your website on all the napkins you hand out with your food. There is no substitute for action.

If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.


For now we’re just getting it out of the room so that our electrician can get started. In any kind of workshop you want plenty of access to power and lots of use of the light. So Mike our electrician is hooking us up. If a service call from an electrician isn’t in your budget you can plan your space so that you can best take advantage of the outlets that are already there. Now Mike has checked all of these surfaces to be sure they can handle these extra outlets he’s adding.
Well I’ve been kind of fighting that, because I wanted to keep it open to where you could have the flexibility of moving things in and out. It probably makes sense. Actually have another old set of cabinets I thought about putting here, maybe put some really good casters on it to where you could keep it here. I’m also, wanted to be able to store like drum sander, other things that can go under it and then you can take those out and put them on this.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
After looking at a number of spaces that are available to lease, you may start to wonder whether it’s better to buy or lease commercial real estate. Of course, there are occasions when it might be better to purchase commercial real estate rather than leasing it. For example, if you buy a commercial space, you’ll take advantage of equity, depreciation, cash flow, and asset appreciation.

We exhausted our entire life savings on this project and entered into a lot of debt at the same time. And now it’s the ongoing maintenance, repairs, insurance, and upkeep on this rig that make it almost impossible for us to keep it on the road. This is where I’m hoping to get that “let’s sponsor you to travel across America and meet the fans” call from Hasbro or Paramount one day soon.
The good news is that when you’re starting your small business, you now have the tools to take a data-led approach to choosing the right store design. For example: Not sure what type of music gets your customers in the mood to spend? Simply choose a few different styles and display a different one each week. After the test is complete, analyze sales data to help you identify what could be impacting sales. The key to getting accurate results from this kind of test is to avoid switching up the other variables in your store that can impact sales, such as signage, or testing one type of music during a regular business week and another type during a holiday week. For more details on how to create controlled in-store experiments, you can check out Lean Retail 101
​There are some diverging paths that you could take at this point: some may want to get a router with a router table for edge work and improved joinery capabilities, some may want to start looking at some of the interesting 3rd party jigs - two of my favorites are the DowelMax and the Kreg Pocket System, but my recommendation would be to equip yourself to buy cheap stock.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
Hand tools offer your best chance of finding a real bargain. Until the early 20th century, nearly all woodworking was done with hand tools, and their designs and uses have changed little. Most of the high-end planes on today’s market, for example, are just reproductions of the original designs. And because the originals were mass-produced, they are fairly easy to find at rummage sales and antiques stores. (For more information, refer to Matthew Teague’s article, “Buying Old Tools,” in FWW #180).
If you want the ability to cook inside your van but don’t have a whole lot to spend, your best option is the Coleman Classic propane camping stove. For about $60 you get a sturdy and reliable 2-burner stove that runs off of replaceable 1-lb propane canisters. We’ve seen many people using these out on the road, and they do the job very well. Coleman has hardly changed the design of these stoves for decades, so you know they’re doing something right.
Household vacs are not designed to handle large quantities of sawdust or wood chips. Their filters clog up quickly, greatly reducing suction. While you can get away with using a small cordless vacuum for small messes, a shop vacuum offers greater power and capacity. Whether you already own a shop vacuum or are shopping for your first, consider purchasing disposable bags or a washable and reusable CleanStream filter.
If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.
In addition to sheer power, look for a model with a built-in thermostat so you can set it and forget it. This convenience feature is well worth it so you don’t have to stop what you’re doing mid-project to manually turn your heater on and off to maintain your desired temp. A good garage heater will mount to the wall or ceiling to save space and will come with a durable housing and full safety screen to keep dust and wood chips from reaching the heating elements and starting a fire.

Once you have an idea of your store layout and a product mapping plan, it’s time to consider your store fixtures and displays. Fixtures are permanent—fixed—parts of your store such as lighting, counters, fixed shelving units, and dressing rooms. Displays hold product and tend to be movable, versatile, and customizable, like modular units, gondolas, tables, slatwall, and clothing racks.
A grid floor plan, also called a straight layout, is a very efficient use of both floor and wall space. With fixtures and displays running parallel to walls, a grid floor plan maximizes every inch of available floor space, including the corners. Grid layouts are easy for customers to navigate and for store owners to categorize. Plus, they offer plenty of end cap and feature wall exposure for promotional items and seasonal products.
Well I think I’ll have plenty of light once we get all of 24 bulbs in place. I’m really glad I saved those old fixtures. Hey another thing we’re reusing, and I’m really glad I saved, is these old cabinets that we took out of a kitchen renovation a couple of years ago. This will be perfect to serve as our base cabinets so that we can build our sturdy countertop on this side of the shop.
Impulse items like small toys, candy bars, lip gloss, and breath mints are great products to feature near your register. When customers approach the register to pay and leave, you don’t want them to stop shopping. Placing low-cost impulse buy items near registers, as shown in the image below, encourages shoppers to add an item or two as they check out.
Ultimately, your workshop should be a place that inspires you to be creative and to do your best work. When you take the time to plan the space for maximum efficiency and comfort, you’ll love spending time there — and that means you’ll get more done, whether it’s fixing up a car or building a new piece of furniture. No matter how you use your workshop, you should enjoy the time you get to work with your hands and make something brand new. So what are you waiting for? Get started designing your perfect workshop today.
Both of those broader lenses are still useful ways to look at app costs, but costs can additionally be broken down by app type and the features associated with them. Also, two years in technology is a very long time. So, we will start by looking at what's changed. We'll then move on to looking at app costs based on the different kinds of apps in the market.
If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.

If you’ve spent time at your local flea or farmers’ market over the last few years, you may have noticed the explosion that has taken place in the number of innovative small business concepts. From cool new clothing lines to ingenious fusion foods, the sheer diversity of the ideas on display really hammers home one of the key lessons when starting a small business: You need to find your key differentiator. For some this is their brand story, for others it’s the value of their service, but for many quick service restaurants and small retailers, it’s a distinctive core product line that demands the attention and interest of your customers.
The idea of not having your own bathroom nearby can be incredibly intimidating, but we’ve found that this is actually one of the easiest parts of vanlife. Public restrooms are plentiful throughout North America, and we’ve never not had a bathroom when we needed one. Gas stations, truck stops, Walmarts, McDonald’s - you name it, we’ve done some business there.
If you don’t have the time (or interest!) in building your own conversion but you still want to give van life a test drive, we’ve got an idea for you! We’d recommend getting a rental vehicle from Escape Campervans. They have 10 different locations across North America and come fully loaded with all the gear you need for an epic road trip. Plus, their rates are fair and affordable.
Sounds fun right? Well the truth is — yes! It’s more than fun, it’s liberating. Sure, there is some risk involved (and a bit of a learning curve). But for those who do it right, who take advantage of the technology available, who build the right support network around them, who get funding from the right sources, and who choose the right people to work with, working for yourself is the new job security.
First, decide on wax you would like to start with, there are three different kinds to choose from Ultimate Small Shop paraffin wax, soy wax, and beeswax. Paraffin wax is most commonly used in candles, this wax is found at most candle making stores. Soy wax is all natural, made from soybeans, and cleans up easily with soap and water. Beeswax is all natural too, and making beeswax candles is often easiest because you simply wrap a sheet of beeswax tightly around a wick then seal it with your thumb, which means no melting is required. To begin, spread newspapers around the candle making area. First, you melt your paraffin or soy wax and it must be double-boiled. Usually, you place a large pot that is about half-filled with water on a burner over low-medium heat, place a melter in the water, then gradually place wax pieces into the melter. When the wax has melted, you can add coloring or fragrance as desired. To make molded candles, cut the wick two inches taller than you want the candle to be, then thread it through the hole at the bottom of the mold, then plug the outside of the hole with putty. Place a pencil or similar item over the top of the mold and tie the top of the wick to it, centering the wick. If the mold is cardboard, plastic, or glass, heat the wax to 130 degrees Fahrenheit. If the mold is metal, then heat the wax to 190 degrees. You can use a candle or candy thermometer to measure this. Ultimate Small Shop Pdf When the right temperature is reached, lift the melter by the handle and slowly pour the wax into the mold. Let cool for twelve hours then refrigerate for twelve more hours, then your candle is ready to be removed. To make votives and other small container candles, you can use pre-tabbed wicks by simply placing them in the center of the votive candle molds or containers, then pour the wax mixture over and let stand for twelve hours, refrigerating the votives. By the time your teen is in high school, you probably aren’t taking as many pictures of them as you used to. I have to keep reminding myself that I only have a couple of years left and no time to waste trying to capture fleeing teenage memories. You might be thinking that I’m really organized to be already working on scrapbooking my daughter’s high school memories. To be honest, I have a shoebox full of pictures of my daughter waiting for me to get to someday. But if I wait until “someday” to continue taking pictures because I already have so many pictures I haven’t done anything with, then my daughter’s teenage years will come and go while I try to catch up. I don’t want to chronicle every detail of my daughter’s life (nor would she want me to!), but I was trying to think of some memories that she might want to laugh about and maybe even treasure someday. Ultimate Small Shop Guide Woodworking So how do you do that without ending up with pages and pages of memories? I decided to do two large (12×12) pages (facing each other in the album) for each year of high school.
To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
So after 14 years in our previous location, my company moved to a new shop last month. My shop went from 1600sqft split into 2 bays with the kitchen in between to a contiguous 2950 sqft. Still don't know why the the office portion needed to grow by the same percentage when there were already 10 empty cubes at the old office, but thats an argument for another day. The boss got his 500 sqft office so he is happy.

So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.
A good starting point here is to write down two or three keywords that you think define your brand and then allow all your design choices to be guided by those words. For example, a local cheese shop could be organic, artisanal, and authentic; a wine bar could be sophisticated, 1920s, French; or a local specialty food store could be gourmet, helpful, natural.
Nicole and I decided not to go public with the cost of the build. Although we are very open about most things, we are a little uncomfortable about making an expenditure of this magnitude public knowledge. Furthermore, unless you live in the Phoenix area and plan on building the same size shop with the same patio and with all of the same finishing touches and labor requirements, the price isn’t all that helpful to you.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
If you have a broker that’s too successful you may be a low priority. If you choose a broker that’s inexperienced but attentive, you may end up paying for their novice mistakes. My advice is to not choose a broker but instead choose a team. Pick a junior/senior combo so that when you’re hunting for space you work more with the junior, and when it comes to negotiating the deal you have the experienced veteran leading the negotiation.”

Plywood comes in several different types, the most common being pine and lauan. We used ¼” lauan plywood for the walls in our van. Lauan is cheap, it bends easily, and in our opinion its grain pattern looks nicer than pine. Hardwood plywood like birch costs more than pine or lauan, it weighs more, and it’s more difficult to bend. This type of plywood is a great option for furniture, but we think lauan is a better choice for your walls and ceiling.
Once you have your space secured, hang some pictures in the windows that illustrate what’s to come. It’s also a good idea to provide leaflets that people can take away with them and hang a clipboard and pen on the front door where people can sign up to hear more about your business. This list is pure gold! So once you have it, why not stage a launch party and invite the local community (and local journalists). The first step for any business is always getting people to try out your products!
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.

Once you’ve got that, you’ll want to familiarize yourself with your tax obligations as a employer, including providing required employee benefits such as social security and workers’ compensation. As an employer you are also responsible for withholding federal and state taxes from your employees’ paychecks. What’s more, you are obliged to ensure all withheld tax is forwarded to the government within a defined time frame (usually a matter of days after the paycheck was issued). Failure to do so can result in a fine.
If you want to operate your business under anything other than your own personal name, you’ll need to register your chosen ‘fictitious’ name with the appropriate county or state authority, otherwise known as registering your “Doing Business As” (DBA) name. The correct filing authority varies state-to-state. The Small Business Administration (SBA) provides a helpful tool to help you find the relevant authority for your state.
Right before you start your small business, everyone has a dream setup for their small business in their head, along with a laundry list of amazing features. It’s probably large and full of natural light, opposite from a park, and filled with beautiful details like a long solid oak counter and a little bell over the door. There’s absolutely nothing wrong with these aspirations. In fact, it’s vital to have a clear vision of what you’re working towards. It can, however become a problem if you let the perfect business location become a barrier to opening your doors in the first place.
So you stayed up all night, thought long and hard, and decided you want to name your designer sunglass hut The Sunny Rabbit. We don’t blame you, it’s a pretty cool name. Most would tell you that the next and most logical next step is to register your business as a DBA or at the state level. But, we’re here to tell you that’s wrong! Here’s why. We just talked about how the right business name can make or break your brand identity and in today’s digitally connected world, securing your brand identity across the web is equally as important.
So what does all this boil down to? I favour starting with a good workbench and top quality hand tools – chisels, a couple of planes, a hammer, a few Japanese handsaws – stuff like that. You’ll be amazed at what you can accomplish when properly equipped. Build simple items at first, and then add the very best power tools you can – as you can afford to – in the order that makes the most sense for the work you’re interested in. Yes, this gets you off to a slower start, but what’s the rush? You’ll soon surpass the ‘buy-it-all-at-once’ folks who end up struggling with beginner tools that hold them back from getting better.

Both kids and adults have sat inside [the Optimus Prime truck] and been brought to tears. For many, it is a dream come true. Some kids are very intimidated by Optimus Prime because of the size and won’t go anywhere near it. But I love making people smile. The fact that I can make them smile for just a few minutes by seeing Optimus Prime on the highway means the world to me.
In a small space, there's not much room for one-trick ponies: You need gear that can do many different things, and that goes for your work space and stands, too. You can add a wood clamp to a multifunction workbench, but you probably need compact work or tool-holding stands to make up for the lack of a large work surface. Occasionally you may need to take your work to another room or even outside, in which case portability is also important.
Do you have a business license? Do you have a permit to open a food service establishment issued by the local health department? Are you applying for a permit to modify the building you wish to occupy? Do you have a health permit from the county health department? Do you have a signage permit? How about an alarm permit from your city or county fire or police departments? These are just a few of the questions you need to ask yourself.

Well I think I’ll have plenty of light once we get all of 24 bulbs in place. I’m really glad I saved those old fixtures. Hey another thing we’re reusing, and I’m really glad I saved, is these old cabinets that we took out of a kitchen renovation a couple of years ago. This will be perfect to serve as our base cabinets so that we can build our sturdy countertop on this side of the shop.


Designing your retail store's interior is a topic that we've been looking at recently in an effort to help boutique merchants be more successful and thrive in today's digital era. From telling your brand's story and creating immersive shopping experiences, to putting together head-turning window displays and signage essentials, when it comes to retail, the devil really is in the details. As such, we want you to help you get the basics down pat. 

​In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts.  Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up.  A more economical approach would be to build your jigs as your projects demand them.  After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.
Hey there Ryan. Cool blog! I love the idea of trucking-it! I’m not able to do something like that, though I wish that I had taken the time when I was younger to do so. Here’s a suggestion that you might consider, if you haven’t already considered it before: Obtaining and using a hammock. I’d suggest bolting in an eye hook on the truck, or using the bumper as a tie point if you don’t have a second tree around. Also, in the high desert, you could use rocks as anchor points for it. Just an idea, from one camper to another.
Assume that there aren’t any decent tools on craigslist or at garage sales, and keep in mind that I have absolutely no tools, dust collection, shop-vac, clamps, sanding & painting accessories, tables, materials to build my own tables/stands/jigs, or anything else—not even safety gear (you’re such a good buddy that you even let me borrow your extra set of goggles and your earmuffs when I used to come over).
If you don’t have the time (or interest!) in building your own conversion but you still want to give van life a test drive, we’ve got an idea for you! We’d recommend getting a rental vehicle from Escape Campervans. They have 10 different locations across North America and come fully loaded with all the gear you need for an epic road trip. Plus, their rates are fair and affordable.
In every aspect when starting your small business you should be mindful of making careful, prudent decisions about the allocation of your potentially limited funds — tracking precisely the cost of goods sold (CoGS) against sales to ensure profitability. Every dollar spent is tracked and accounted for, either as an essential cost of doing business (rent, employees, etc.) or as a cost of inventory that will result directly in profit.

Ever wonder why you walk into a supermarket and the first thing you see is fruits and vegetables rather than toilet cleaner? The complex art of displaying arrangement and the perfectly optimized in-store customer journey can seem like some sort of semi-magical, commercial Feng-Shui. But it’s actually just business 101. At its core, store design is a fairly simple exercise. Think about your shop’s layout from a customer point of view and consider what might surprise and delight you, what might annoy you, and most importantly, what might convince you to make a purchase.
A table saw is one of the most important tools in the workshop for its ability to make long straight cuts. It will also cross cut with ease and if you don’t want to cut clean through a board you can adjust the height of the blade to make a dado or rabbet. A handy feature with the BTS10ST table saw is the vertical stand which also saves on storage space.
Hey, I hope we’ve been able to share with you some ideas that you can use if you’re thinking about building a workshop or any type of hobby room or just about any room in your house that you can get this kind of enjoyment out of. We have a lot more details on this shop as well as other things you need to consider if you’re building a shop on our website at todayshomeowner.com. hey thanks for being with us.
As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
It is also essential to take a lean, data-led approach to choosing a business space. The average length of a commercial lease has dropped over the last few years but is still often well over five years, so the absolute last thing you want to do is rush into a signing and get locked into a bad situation. There are so many ways to test the viability of your business idea before you over-invest and sign a full-blown lease agreement.
You’ll want to consider your insurance needs both in terms of the potential frequency of claims against you and the size of the potential liability. You’re also going to want to think carefully about your assets and what you can and cannot afford to lose. A good rule of thumb is to always buy insurance if you can’t absorb the loss of a particular asset without dramatic effect.
There are some variances in the features and reliability of different model years, and differences between the Mercedes Sprinter, Dodge Sprinter, Ford Transit, and Dodge Promaster - so make sure to do your research. The Sprinter RV Conversion Sourcebook is an incredible resource on all things Sprinter (and van conversions in general), and it goes over all the options in detail.
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
These basics are going to set you back about $180, leaving you with $320 left to work with.  We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives.  This should lead to more consistent results, more enjoyable builds, and increased efficiency.  These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
Thanks again for the inspiration. I've just finished putting the door on my 12x16 shop. Aside from shingles it is ready for the winter. I've yet to cut out the hatch for the lumber or start on the interior, but at least it's weather tight and I can work on the rest I the coming months. I am planning to use mineral wool bays for insulation to mitigate sound and ease installation. I don't see a way to add pictures to this reply (I'm on my phone), so I'll try to add one or two later.

Expert Tip: Banks are often reluctant to provide long-term small business funding. They prefer short-term loans that are associated with physical assets, which can then serve as collateral. So instead of just asking for a generic loan, maybe consider raising capital for specific equipment that will kickstart your new business, like an espresso machine or delivery vehicle.
×