Store design experts advise small retailers to keep versatility in mind when choosing product displays. Your stock will likely change over the years. If you install permanent, unmovable displays, you will likely regret it later. Adjustable display options such as slatwall, gridwall, apparel racks, and shelving tend to be good choices for small retailers.

The subfloor provides a stable layer - basically a sheet of plywood - for your floor to sit on. You’ll see a lot of van build videos on Youtube showing a ¾” subfloor, but that thickness just isn’t necessary in a van. The thicker the subfloor, the higher the cost and weight, and the more valuable interior space it takes away. We recommend using ¼” plywood for your subfloor, which is plenty thick enough for a van.

First, decide on wax you would like to start with, there are three different kinds to choose from Ultimate Small Shop paraffin wax, soy wax, and beeswax. Paraffin wax is most commonly used in candles, this wax is found at most candle making stores. Soy wax is all natural, made from soybeans, and cleans up easily with soap and water. Beeswax is all natural too, and making beeswax candles is often easiest because you simply wrap a sheet of beeswax tightly around a wick then seal it with your thumb, which means no melting is required. To begin, spread newspapers around the candle making area. First, you melt your paraffin or soy wax and it must be double-boiled. Usually, you place a large pot that is about half-filled with water on a burner over low-medium heat, place a melter in the water, then gradually place wax pieces into the melter. When the wax has melted, you can add coloring or fragrance as desired. To make molded candles, cut the wick two inches taller than you want the candle to be, then thread it through the hole at the bottom of the mold, then plug the outside of the hole with putty. Place a pencil or similar item over the top of the mold and tie the top of the wick to it, centering the wick. If the mold is cardboard, plastic, or glass, heat the wax to 130 degrees Fahrenheit. If the mold is metal, then heat the wax to 190 degrees. You can use a candle or candy thermometer to measure this. Ultimate Small Shop Pdf When the right temperature is reached, lift the melter by the handle and slowly pour the wax into the mold. Let cool for twelve hours then refrigerate for twelve more hours, then your candle is ready to be removed. To make votives and other small container candles, you can use pre-tabbed wicks by simply placing them in the center of the votive candle molds or containers, then pour the wax mixture over and let stand for twelve hours, refrigerating the votives. By the time your teen is in high school, you probably aren’t taking as many pictures of them as you used to. I have to keep reminding myself that I only have a couple of years left and no time to waste trying to capture fleeing teenage memories. You might be thinking that I’m really organized to be already working on scrapbooking my daughter’s high school memories. To be honest, I have a shoebox full of pictures of my daughter waiting for me to get to someday. But if I wait until “someday” to continue taking pictures because I already have so many pictures I haven’t done anything with, then my daughter’s teenage years will come and go while I try to catch up. I don’t want to chronicle every detail of my daughter’s life (nor would she want me to!), but I was trying to think of some memories that she might want to laugh about and maybe even treasure someday. Ultimate Small Shop Guide Woodworking So how do you do that without ending up with pages and pages of memories? I decided to do two large (12×12) pages (facing each other in the album) for each year of high school.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
Make sure the room or building you are planning to utilize has sufficient lighting and electrical outlets to allow you to see what you are doing, and to work without excessive extension cords. You should also remember that many tools require a fairly substantial amperage to operate, so you need to make sure the wiring is capable of handling the loads. 20 Amp circuits will work for ordinary 120V tools, but air compressors and welders may require 40 Amp, 220V circuits.
“If it’s a retail space then location is critical. Proximity to other retailers, access to transportation, and visibility/signage opportunity can be critical. In this case, there may only be 4 or 5 spaces available that meet the business’s criteria and objectives. A good broker will sometimes develop creative alternatives that might be outside the locational parameters but offer other advantages – such as co-tenancy or lease term flexibility.

Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
The time of the travel agent might be passing, but people are still looking for those with a knack for more nontraditional travel coordination. If you always plan the perfect vacations complete with beautiful hotels, the ideal location, and a bevy of delicious restaurants lined up for every evening, consider advertising your services as a more modern approach to travel planning.
Starting your own small business can be an incredibly rewarding experience both personally and financially. However, like anything worthwhile, it takes a great deal of time and effort to be successful at it. Your results will depend on how much you are willing to apply yourself. The lessons in How to Start a Small Business 101 are designed to give you a leg up on the competition so you can hit the ground running. Now all you’ve got to do is bookmark this page, free up some time, grab a cup of coffee, and start making your way through each section.
Just stumbled across your article and it’s right on time as I am about to launch a special events venue (ballrooms, meeting rooms, outside garden area, outsourced caterer, etc). Not sure what type of zoning this business falls under. I read that zones are usually for office, retail, industrial and leisure. Any idea what type of zone I should be looking for? Also first time trying to get a commercial space for this type of business, any specific suggestions?

The kind of apps that fall into this app type are extensive. Facebook, Instagram, Snapchat, Twitter, WhatsApp, Pinterest, and YouTube are all examples. Remember that some of these apps have been worked on for many, many years. Thus, a v1.0 social app or social networking app will likely not offer all of the same features. For instance, Snapchat did not start with videos, filters, or their "Stories" functionality. A social app would, however, include user authentication, friending, favoriting (or other data interaction), some sort of messaging, and comparable "baseline" functionality.
I will also typically secure those sorts of items under my locked platform if I am gone for a few days in the backcountry, because in reality I could probably care less if someone broke in and stole my box of food, versus someone who stole my clothes or expensive down jackets, which would be much more problematic (and costly) to replace on the road.
I framed and sheathed each wall individually and then stood them up with the help of long 2x4 braces.  My neighbor let me borrow his framing nailer, which made things go much faster.  I added a second cap of 2x4 on the top to make the walls a little more rigid.  I then laminated 4 2x4's to construct a ridgeboard.  I nailed in some temporary 2x4 supports and had a friend help lift it into final position.  Once all of the rafters are cut and nailed into place, the supports were removed.
However, since you may not have "aisles" per say in your store, it's still important to think about grouping products in a way that makes sense from a shopper's perspective. Also, remember to keep "higher-demand" products displayed at eye-level while placing lower-grossing products at the bottom or above eye level. Lastly, It's recommended that you change up these speed bumps weekly or regularly enough to create a continued sense of novelty for repeat visitors. 
There are certain sayings that hold true and when buying clamps and measuring equipment parting with cash for quality make sense. But which clamps? G, F, sash, spring or strap? There are so many clamps and measuring tools available. Let the project decide which ones you need. As a reassurance, our Axminster Trade Clamps come with a lifetime guarantee, so this is one investment that literally lasts that long.
If this all sounds too complex for you, there are alternatives. Thanks to advances in technology, there are tools available that help simplify bookkeeping and accounting so that you don’t have to hire a full-time accountant to take care of the basics. We’re big believers that a technology-led approach to running a small business will leave you with more actionable insights, more time to focus on your day-to-day operations, and ultimately, more money. For details on the cloud-based technologies that more and more businesses are relying on, make sure to check out our cloud-based business guide.
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette pack­age. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provin­cial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effec­tively through your drawings that your structure will comply with the techni­cal requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
I’m a 60 year young widow who just bought a bright yellow 2003 S10 step side with the intention of camping in it. But I discovered that finding a used S10 step side topper is harder than finding hen’s teeth!! Buying a new one wasn’t an option. Just found a black step side topper for a Ford Ranger. Isn’t a perfect fit but it works. And the colors compliment each other although color wasn’t my primary concern. I took two days to drive from the St. Louis area of MO to the Kansas City area to pick it up.
Thanks for the quick reply. Sounds like you haven't had any big problems with the moisture. I'm in NoVA too, so that bodes well for me. I was considering finding some tyvek house wrap or something to go around the walls in addition to a plastic vapor barrier under the floor, but it sounds like that is not going to be necessary. I was also thinking I'd try to find a window AC unit to use like you did. I like how you mounted yours up high.

Whether it’s underwear in an apparel store or milk in a grocery store, the items customers need most usually are found near the back. Think about this next time you’re in a grocery store. As you walk to the back of the store to get milk, you funnel past coffee, cereal, and toilet paper. And the milk is right by the eggs and cheese. This is primary and secondary zone merchandising in action, and the reason people shopping for one item often leave with three or more.


The tablesaw—This tool is the backbone of nearly every shop, and for good reason. It allows unmatched precision in ripping parallel edges and crosscutting at a variety of angles. Most woodworkers find it crucial for the basic milling of stock. It is also suited to many joinery tasks, easily producing tenons, box joints, and—with a reground blade—the tails for dovetail joints.
Thanks again for the inspiration. I've just finished putting the door on my 12x16 shop. Aside from shingles it is ready for the winter. I've yet to cut out the hatch for the lumber or start on the interior, but at least it's weather tight and I can work on the rest I the coming months. I am planning to use mineral wool bays for insulation to mitigate sound and ease installation. I don't see a way to add pictures to this reply (I'm on my phone), so I'll try to add one or two later.
Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regula­tions, a larger lot, or more congenial neighbours. 

Often times those same freedom-seeking, passion-driven individuals that started their journey filled with courage and optimism, become some of the most time-pressed and financially-stressed people out there. The flip side of getting to create your own wealth is that you are solely responsible for creating your own wealth. That’s right, it all comes down to Y-O-U.


We use this fan for extra circulation when it’s hot, and to get the air moving when it’s cold at night and we have all the windows closed. We also keep it on for our dogs while we’re driving. There are cheaper 12V fans out there, but generally the cheaper the fan the more power it draws. The Endless Breeze is a great little fan, and it’s definitely worth getting for the added ventilation.
The way that you fill these roles will depend on the size of your company and how much you’re hoping to invest when building your marketing team.  If, for example, you’re looking to bring on a single marketing employee who will handle all these functions, you’ll need to find somebody with a broad set of experiences and the ability to handle multiple job roles.

I’m picking up a 4×4 Extra cab pick up tomorrow and selling my current 97 Tacoma. It’s older and it’s got a lot of miles but it still has a lot left to go. Mine is available in the 3 grand range. They’re hard to find and all the rust free trucks are out here in the west but mine is one example of many good Tacos that are available at an affordable price that will fit the bill perfectly.


Also, heard of anyone camping in an Accord sedan? I’m wondering if it’d be worth it to buy a new Tacoma to convert into a dirtbaggin’ vehicle or if I should try to make it in a sedan. Lots of variables… I’ve got the cash but it’d eat into the “cushion” I have for living on the road (about 50% of it). OTOH I could buy a used Tacoma, but they hold value so well it’d seem like long term it’d be best to get it new. I’ve seen some with 250 miles sell for $8,000+. Thoughts on getting a new truck using my beat-up sedan?
For small business owners, these tools present an incredible opportunity to set smarter business goals and easily identify some of the key factors of success and growth in their business. However, when you couple the breadth of technology options with decisions about basic store and restaurant equipment, such as espresso machines or air conditioning units, it can become a little overwhelming to figure out what is actually worth the investment.
Hello! My name is Donna Jean. I love to read books and my job is to write a daily review of all the novelties in the world of eBooks. I allow only the best of them to be published on my website. I really hope to make our world more bright, beautiful and kind. You can participate by downloading any book from my site, and you will receive health, luck, kindness, and love, which will support you during all your life. Wishing your dreams begin to come true, and every tomorrow be happy for you. Thank you! ❤❤❤
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
If you are going to apply for a trademark, make sure to conduct a comprehensive search, like the one mentioned in ‘Securing Your Business Name’ to ensure no one is already using your proposed name in a similar capacity. The United States Patent and Trademark Office also provide a simple search tool that will quickly let you know if you’re potentially infringing on someone else’s turf from a legal point of view.
Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.
Chances are if you’re starting a new small business, you’re not afraid of a little risk. However, it’s also highly likely that you have invested a large amount of money in this new endeavor. It is only prudent to take sensible steps to minimize the impact of unexpected events, like the untimely death of a business partner, a lawsuit from a customer or employee, or a freak accident of nature.

As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.


At $300, the saw is expensive, but it is one of the more affordable saws that offer a 12 inch blade and a double bevel.  The double bevel allows you to adjust both the angle at which the blade cuts into the wood and the tilt of the blade relative to the workpiece.  Having control over both angles allows much easier cuts of trims and moldings.  It's one of those features that you won't use with every project - but when you do need it, you'll be glad you have it
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
If you have some experience under your belt, put it to good use as a life or career coach. Many of us are looking for guidance in our careers -- and finding someone with the time to mentor us can be tough. Life/career coaches don’t come cheap, but they are able to offer clients the intense and hands-on training and advice they need to make serious moves in their personal and professional lives. After all, sometimes everyone just needs some uplifting advice.
First, decide on wax you would like to start with, there are three different kinds to choose from Ultimate Small Shop paraffin wax, soy wax, and beeswax. Paraffin wax is most commonly used in candles, this wax is found at most candle making stores. Soy wax is all natural, made from soybeans, and cleans up easily with soap and water. Beeswax is all natural too, and making beeswax candles is often easiest because you simply wrap a sheet of beeswax tightly around a wick then seal it with your thumb, which means no melting is required. To begin, spread newspapers around the candle making area. First, you melt your paraffin or soy wax and it must be double-boiled. Usually, you place a large pot that is about half-filled with water on a burner over low-medium heat, place a melter in the water, then gradually place wax pieces into the melter. When the wax has melted, you can add coloring or fragrance as desired. To make molded candles, cut the wick two inches taller than you want the candle to be, then thread it through the hole at the bottom of the mold, then plug the outside of the hole with putty. Place a pencil or similar item over the top of the mold and tie the top of the wick to it, centering the wick. If the mold is cardboard, plastic, or glass, heat the wax to 130 degrees Fahrenheit. If the mold is metal, then heat the wax to 190 degrees. You can use a candle or candy thermometer to measure this. Ultimate Small Shop Pdf When the right temperature is reached, lift the melter by the handle and slowly pour the wax into the mold. Let cool for twelve hours then refrigerate for twelve more hours, then your candle is ready to be removed. To make votives and other small container candles, you can use pre-tabbed wicks by simply placing them in the center of the votive candle molds or containers, then pour the wax mixture over and let stand for twelve hours, refrigerating the votives. By the time your teen is in high school, you probably aren’t taking as many pictures of them as you used to. I have to keep reminding myself that I only have a couple of years left and no time to waste trying to capture fleeing teenage memories. You might be thinking that I’m really organized to be already working on scrapbooking my daughter’s high school memories. To be honest, I have a shoebox full of pictures of my daughter waiting for me to get to someday. But if I wait until “someday” to continue taking pictures because I already have so many pictures I haven’t done anything with, then my daughter’s teenage years will come and go while I try to catch up. I don’t want to chronicle every detail of my daughter’s life (nor would she want me to!), but I was trying to think of some memories that she might want to laugh about and maybe even treasure someday. Ultimate Small Shop Guide Woodworking So how do you do that without ending up with pages and pages of memories? I decided to do two large (12×12) pages (facing each other in the album) for each year of high school.
A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information.
Radiation is heat transferred through air or a vacuum- think the heat radiating off of a fire. In a van, the biggest source of radiant heat is your windows. Sunlight (radiant heat) shines in through the windows and heats up the inside of your van. Using a reflective window covering will help deflect radiant heat and keep your van cool. Reflective surfaces also help keep radiant heat inside the van during the winter.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.

One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.


Different approach in that they hung one end of the sleeping platform with hooks and U bolts. One of the best write ups with full details about rigging up an electrical system with second batteries and an isolator, as well as using power inverters. They were then able to incorporate cool things like a mini fridge, lights, and mini PC fans for air circulation.

Another option to consider is an expensive but efficient Festool dust extractor. These dust extractors are designed to work with other Festool tools, but they also match up with most other brands' compact power tools as well. A nice thing about Festool's vacs is that the hoses dock neatly inside the units. There's almost nothing I value more for a compact shop than self-contained storage.
We use this fan for extra circulation when it’s hot, and to get the air moving when it’s cold at night and we have all the windows closed. We also keep it on for our dogs while we’re driving. There are cheaper 12V fans out there, but generally the cheaper the fan the more power it draws. The Endless Breeze is a great little fan, and it’s definitely worth getting for the added ventilation.
I don’t have recs because I’ve always just gone the traditional cold weather camping route with warm clothes, winter sleeping bag, boiled water in a nalgene, shot of olive oil before bed, etc, etc. Perhaps someone else might chime in… I’ve heard of folks (with the appropriate dual battery setup) using electric blankets, or yeah, the Mr. Propane heater (but not while they are asleep).

When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.


It might sound harsh, but when starting a small business your online presence is crucial. If you speak to some experienced local business owners, many will denounce the existence of online review sites like Yelp and Google Local. They’ll tell you about the added time and pressure they now face to maintain social media profiles for their businesses. A lot of local entrepreneurs will share their bad experiences with online daily deal websites like Groupon. But all that complaining doesn’t change one established fact that the internet isn’t going anywhere.
Use the scrap piece of plywood to map out the angle for the speaker stand legs. Decide the height you want for the base of the speakers, and make a mark on the plywood (32 in. for us). Mark the depth of the speaker (13 in.). Lay the 1x4 board assembly on the plywood, lining it up with both the corner of the plywood and the 13 in. mark from the edge. Scribe along the 1x4 board assembly, take the assembly away, and find your angle with a protractor or speed square (17 degrees for us). Cut that angle onto one end of the 1x4 board assembly.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
So far it has worked out. It's probably not ideal. I imagine a system would work much better, but it gets the job done until then. I ended up setting up in my small 1 car garage as well now. I used two shopvacs to build a system in there. I have a few new Instructables to put together and a new shop tour to do as well. Thanks for the comment! FYI: The wood storage has passed the time test. I have not had to change a thing about it. I plan on adding a shelf above the sheet goods to store thin moldings and cut-offs. I still find it incredibly easy to access my wood quickly with that setup. I have to move stuff around in the garage to get to my wall mounted wood storage, so it's more of a pain.
Are your table saw accessories where you need them—when you need them? Follow reader D. E. Warner’s advice: Attach pegboard panels to the stand to hold the wandering herd of push sticks, blades, throat plates, wrenches and jigs. On an open metal stand with angle-iron legs, drill holes in the legs and bolt the pegboard in place. Here’s another super storage project using pegboard.
If you want the ultimate vehicle to customize for your DIY van conversion, the Sprinter is the van for you. They have enough headroom even for tall people to stand up, and enough interior space to design any kind of layout. They also typically have diesel engines, which means greater fuel efficiency and engine life (many diesel Sprinters have been known to make it past 400,000 miles). If you think you’ll be doing a lot of off-roading, the Mercedes Sprinter also comes in a 4x4 version.
As always, great article! While my dirtbag adventure will likely only be about 6-7 months, I am starting to wonder about logistics. You mention that most people use the automobile they have. I drive a Prius. Not ideal for sleeping in, but I’m a pretty content ground dweller. I know that long-term I may start to question this. Here’s the proposition I’m considering: by saving on gas (45-50 mpg), I can occasionally cough up the money for lodging when I feel the need for added comfort. I can definitely do the number crunching, but I’m wondering if you’ve encountered people doing this or did similar analyses of your own at any point. I’d love to hear any insights you may have on this.
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.
A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information.
Will this make me money? If it will not, cross it out. If you want to keep it on, please rephrase your goal so the outcome can be money driven. For example: Grow Instagram following (bad) vs. use Instagram to drive traffic and sales to website (winner!). This way, you can break that goal down into tasks ( ill show you that in an another step) and those tasks will lead to you actually making money with that goal instead of with just a larger Instagram following.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
Once you’ve planned the basic layout of your workshop and have added all the tools and speciality appliances you need, take a last look at the overall design to make it aesthetically pleasing. Add overhead lighting for general illumination and task lighting over your work stations so you can see your project clearly. For maximum flexibility, you can mount clip-on work lights to nearby shelves and point them where you need them, knowing you’ll be able to move them about as required for different projects.
If you have some experience under your belt, put it to good use as a life or career coach. Many of us are looking for guidance in our careers -- and finding someone with the time to mentor us can be tough. Life/career coaches don’t come cheap, but they are able to offer clients the intense and hands-on training and advice they need to make serious moves in their personal and professional lives. After all, sometimes everyone just needs some uplifting advice.
Simply get a one-inch drywall screw and drive it into the hole right beside the hook. You want to use a one inch screw because you don’t want to hit the wall behind it and you just drive the screw in until the head of it is tight against the hook, it’ll just act as a shim, and you’ll see once I get this all the way in, it lock the hook in place, and now when you take the tool on and off it won’t come off. The hook won’t pop out.
A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.
First things first, the machinery is going to do the bulk of your work. Hand tool purists may argue differently but how many machines do you have in your home to make things easier? The same should be true for your workshop. Yes, there may be moments when you take a deep breath at the initial investment but if you’re looking at woodworking as a prolonged pastime then the tools will last you for years to come. Plus you’re not buying everything at once. Start small and build up your collection.
Reactions are typically over-the-top excitement. Everywhere I go, there are people snapping pictures, taking videos, and giving me a “thumbs up.” Sometimes while on the highway, cars will go ahead of me about a mile or so and then pull over to get out and video me driving by them. Truck drivers are always getting on the CB radio asking about the truck.

The beauty of a portable A/C unit is that you don’t have to heft it into a window and block off a valuable source of fresh air for keeping paint fumes at bay. Instead, choose a model with a low profile that you can tuck under a table or against a wall when not in use — a model with casters for maximum maneuverability is ideal. Choose a high-powered unit that will condition at least 400 square feet of space and move it where you need it for maximum comfort as you work.
Commercial law exists for one simple reason: money and trust have a long and storied history of mixing like oil and water. Throughout the millennia-long history of commerce, aspiring businessmen and women have been lied to, cheated, scammed, cajoled, bullied, and otherwise disconnected from every single dime they had by unscrupulous suppliers, greedy investors, and dishonest business partners.  
When Julie Owen bought Cocobolo Interiors in 2008, she set about adding more contemporary items to the Armonk, N.Y., shop. But with only 3,000 square feet, she struggled to figure out where to put her expanding line of furniture, lighting fixtures and accessories. Her solution: create sections within the shop and arrange the furniture the way customers might imagine it at home, using low bookcases and folding screens as dividers.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.

They’re also very energy-efficient, so they won’t be a heavy load on your batteries. The best 12V fridges use highly-efficient compressors that have very low power draw (0.7 - 3.0 Amps per hour, depending on the model and the ambient temperature). They’re also well-insulated and feature top-open lids, which prevent the cold air at the bottom of the fridge from escaping when the lid is open.

I think it would work pretty well for a music festival, I don’t see why not. I wouldn’t say it is robbery proof, but generally robbers are looking for quick and easy targets, like a purse sitting on the front seat, just smash and grab. If someone really wanted to rob what was under they platform, they surely could, but they’d need more tools and more time to do so. And they don’t even know if there is anything good under there… I’d like to think of it as a really good robbery deterrent.
When starting your small business, the type of business structure you choose will depend on three primary factors: liability, taxation, and record-keeping. Most small business owners begin their commercial life as a sole proprietor because it’s the easiest way to get started. In fact, if you’re in business and you haven’t taken any action to incorporate, you are most likely deemed a sole proprietor by default. You are entitled to all the profits of your business but also responsible for all its debts, losses, and liabilities.
You’ve probably considered what goods and services you’ll be offering, but have you researched the cost of sourcing your raw materials? How about the cost of turning those raw materials into your finished product? Do you understand how much you’ll need to charge for your products/services in order to cover the expenses of renting a space, paying employees, leasing equipment, and paying for permits and regulations? Moreover, have you considered if the answers to these questions will provide the kind of operating margin you’ll need to pay yourself a salary?
Most businesses must obtain a variety of business licenses, permits, and registrations before opening their doors to the public. As a small business owner, it is your responsibility to ensure that you are abiding all the laws and regulations applicable in your state and to your particular industry. You also have to research and apply for all relevant permits and licenses that apply to your business type and location. Remember, it is impossible to plead ignorance as a defense. It’s up to you to educate yourself. When in doubt leave it to the professionals. CT Corporation offers custom license packages that simplify the process for business owners. Click here for an example of what that looks like.

A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.


That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
Now that you have written everything out, now take out a calendar that has 12-month blocks and map out each business goal in the corresponding month that it has to be completed by (or accomplished). So you have 12 squares (12 months) and you are literally placing these ideas into the month you want to accomplish them by. By the time you are done with this, you will have a sheet of paper with all your ideas written into the months on the calendar.
I have a basement shop with a walk out and a seperate entrace to my shop.I have approx. 5oo sq feet to work in there, there is natural light that comes in with a graet view of the lake that we live on.I have started to dress up my shop after making such beautiful furnisher for other people it started with a bench witch is 11 ft, long and plenty of stoarage space under the bench , the low storage aera of the bench is made from black walnut and the bench top is oak with bubinga trim. Saw cabient is white oak ,miter saw cabient is walnut ,american chestnut ,cherry and maple. Now the joint cabient looks out of place so I will be making a better looking cabient for the 6in. jointer. I had made a plant self to start plants along the widows but took it out and put a bench top there so it looks as a big window sill but I use it for a place to set tools as I am working on the bench also I have put walnut around the widows and painted the walls.There is a 10in. powermatic table saw,powermatic drill press fl.modle,rockler 6in. jionter, mekeita compond saw,delta 14in band saw, I have two planers and a table mount router in my bench top ,also there is an old american lath witch I have in stoage and a sears jig saw.

One thing I found while looking on the topper websites is a piece of weather strip designed to go between the tailgate and the truck bed. It has a special wedge shape to it so when you close the tailgate it makes a watertight seal. It is just the thing to keep the dust and dirt from entering the back of your rig when driving down the dirt roads. They’re inexpensive too, for a full size truck like my Dodge it’s only $25. It has adhesive on one side, so installation looks simple.
“Your sales floor is a living, breathing entity that needs to change—frequently—in order to flourish. It’s the retailer’s job to make that happen. If your store is filled with the latest and greatest products, but your sales are in a rut, it could be because your customers are bored. They come to your store not just to buy; they come for ideas and inspiration. And they come to be entertained—even when they don’t buy anything, that experience is what brings them back.”
Boy you guys are spoiled, lol. There will always be at least some echo in the shop. I wouldn’t judge the acoustics based on this video though since the shop was still being put together at the time. No cabinets and no floor tiles, so the echo is to be expected. Have you seen the latest video? http://www.thewoodwhisperer.co.....rock-star/ The sound is dramatically improved over the Dream Shop video and all I did so far was add a few floor mats here and there. By the time the cabinets are in and I get some nice rubber floor tiles in place, the sound should be at least to the level of the old shop if not better. Right now though, my priority is on building a bed and I do consider the current sound to be “acceptable” for web videos. I’ll focus on tweaking things when I finally get some spare time. Considering adding some acoustic tiles to the ceiling.

“Your sales floor is a living, breathing entity that needs to change—frequently—in order to flourish. It’s the retailer’s job to make that happen. If your store is filled with the latest and greatest products, but your sales are in a rut, it could be because your customers are bored. They come to your store not just to buy; they come for ideas and inspiration. And they come to be entertained—even when they don’t buy anything, that experience is what brings them back.”


The first is that they will need to be powered by a product catalog. Many times that already exists and an app will just leverage APIs or web services to pull back products. If it doesn't, however, it will require either a custom buildout (beware!) or leveraging platforms like Shopify, Magento, or comparable solutions. The strength of these tools include providing the administration interface to add new inventory, APIs or SDKs, ways to store items in a cart, and similar features. The downsides are that you'll be limited by their workflow and customizations.

When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
We all know that we’re not supposed to judge a book by its cover. The truth is however, that it’s human nature to judge based on appearance. Though most of the time, despite our good intentions, it happens unconsciously. As consumers we make incredibly quick decisions about the businesses we choose or choose not to frequent. As we enter a location we take in the signage, the windows, and the product displays. And with the blink of an eye we determine a dozen different factors. Is this location trustworthy, clean, and friendly? Is the staff likely to treat me well? Will the products be to my liking? Will I find what I need and complete my purchase quickly? Can I even afford to shop here? And, perhaps most importantly: Is there something unique about this place?
A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.
Well, all these years we’ve always planned on this being a nice little workshop, and now’s the time that we’re about to remove all of this and create a nice realistic, practical workshop. Not a TV workshop that just looks good, but one that will be perfect for us to use for some of the projects we have on the show, and again it will be used by our construction company for some of the projects they have.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
Find out what tools you need and how to budget for shop setup. Whether you are going to be doing furniture, cabinetry or woodturning, this workshop tools list and budgeting guide can help. Learn how to prioritize purchases of shop tools based on space, interests and cost. Check out a comparison of the workshop tools you can get for $4000 vs. $10,000 and determine how much you need to spend for the shop you want.

If you’re starting a small business for the first time, your new best friends in life should be your bookkeeper and your accountant. The former should be engaged for a few hours every week (especially at the start of your business) to compile your books and ensure your records are maintained to the required standard, while the latter will help review your tax situation and prepare financial statements. Both can also be used as invaluable sources of actionable intelligence about ways to reduce costs, increase margins, and generally streamline your finances.You’ll be able to spend all that time you save doing what you love and thinking strategically about your business.
Listing agents are hired by a landlord to list their commercial property. Listing agents earn a commission that’s paid by the landlord, typically between 3% – 6% of the total lease. Tenant brokers, on the other hand, represent tenant interests. However, tenant brokers also typically earn a percentage of the overall commission paid by the landlord, knows as the tenant broker’s fee.
Plywood comes in several different types, the most common being pine and lauan. We used ¼” lauan plywood for the walls in our van. Lauan is cheap, it bends easily, and in our opinion its grain pattern looks nicer than pine. Hardwood plywood like birch costs more than pine or lauan, it weighs more, and it’s more difficult to bend. This type of plywood is a great option for furniture, but we think lauan is a better choice for your walls and ceiling.
If you live where summers get hot and humid, you may need more than a fan to keep cool in your workshop. Fortunately, air conditioners will both dehumidify and cool your space — and you don’t need a traditional window to get the job done. Instead of a residential window unit, consider a freestanding portable air conditioner that you can use as needed on hot days.
Once you’ve got that, you’ll want to familiarize yourself with your tax obligations as a employer, including providing required employee benefits such as social security and workers’ compensation. As an employer you are also responsible for withholding federal and state taxes from your employees’ paychecks. What’s more, you are obliged to ensure all withheld tax is forwarded to the government within a defined time frame (usually a matter of days after the paycheck was issued). Failure to do so can result in a fine.
Fantastic build and opportunity for you. I really appreciate your humbleness given the great asset you have in the new shop. You flaunt/market what you do and where you do it because that’s the business you’re in, but at the same time you understand what a great tool you have in the shop itself relative to what most folks will ever acquire. Well done.
Ultimate Small Shop offers a comprehensive guide illustrating how to set up a workshop. It may be just a small basement shop or a part of the garage converted into a workshop. The guide lays out all the steps and actually caps the investment at under a thousand dollars. Woodworkers can build their workshop for less than $1,000. This does not entail any compromise of tools or the scope of woodworking projects. The guide provides a shopping list including the best tools and there are exact links to find those tools and buy them at the best prices. There are floor plans to ensure layouts are optimized even in the most cramped spaces.
Tip: Save money on specialty displays! Many manufacturers offer retailers low-cost or free specialty display fixtures designed to highlight their branded lines, like the one pictured below. These make great speed bump or outpost display units on a tight budget. Your product line reps can tell you if they’re available, plus provide merchandising and display advice.
Hospitality expert, Chip Conley founded and grew the Joie De Vivre hotels from a single San Francisco location to become California’s largest boutique hotel management company. How? He understood the value of a unique vision when it’s consistently applied. He created each hotel to reflect the spirit of a niche-oriented magazine that he felt represented his target market. Examples include the Phoenix (Rolling Stone), the Rex (The New Yorker), Hotel Avante (Wired), Wild Palms Hotel (Fast Company), Hotel Los Gatos (Town and Country), and the Water's Edge (Yachting). Obviously your inspiration doesn’t need to be a magazine, it can just as easily be a song, a group of words, or just a particular image. Find something that resonates with the customers you have in mind and design your store to reflect that vision.

So after 14 years in our previous location, my company moved to a new shop last month. My shop went from 1600sqft split into 2 bays with the kitchen in between to a contiguous 2950 sqft. Still don't know why the the office portion needed to grow by the same percentage when there were already 10 empty cubes at the old office, but thats an argument for another day. The boss got his 500 sqft office so he is happy.
There you have it! Now you have no excuses, you must start planning right away. Please remember this can take a lot of time and a lot of work, so be sure not to stare at your task list in its entirety too often. I don’t want you to get overwhelmed knowing all the things you must get accomplished. Just focus on the goal that is the most important and attack it, task by task. Need help organizing these goals? Check out my Goal Planning Worksheets here:

If you have the available time, taking your DIY campervan for a test run (or two) is a great way to identify any problems while you still have access to tools, package deliveries, and a place to work. There’s just a lot that you can’t foresee until you live in your van. Taking it out for some short trips throughout your build will help you understand how you’ll actually use your new living space, what’s necessary, and what’s not.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
I know in Missoula the garbage men do not like unbagged dust chips. They sent my friend a warning notice in the mail. Do you pull your drum out to the garbage and let the dust fly or dump it into a bag? My friend has garbage cans with 33 gallon liner which he pulls out of a sealed dust collection box beneath the cyclone… then he uses a hand truck to haul it out to the alley and then puts a fresh can in the box. It seems like a simple dust management method by not handling the dust by either scooping or dumping it out into a bag. I am always trying to think of ways to have less contact with harmful dust particles and I am curious as to how others handle the situation. Have a great weekend! 

You are also obliged to file a quarterly tax return which must detail, amongst other things, your employee pay and withholdings. Once again, failure to do this can result in, you guessed it, a fine! As you can see, it’s important to be up to speed on the rules and regulations around taking on employees, including, of course, provisions around hiring foreign workers. The good news is that there are a number of affordable payroll software providers that automate this process very effectively.
Whether you end up looking at self-checkout counters, fancy lighting systems, special refrigerated cases, or any of a countless number of options, never forget that these are only tools to help accomplish your main goal. Your store needs to create an environment where customers want to be, where they feel comfortable and appreciated, and where that experience will prompt them to purchase (and hopefully encourage their friends to do the same). Equipment and technology decisions should always be made with your customers in mind.
×