Firstly, more and more consumers are rebelling against the generic offerings of big-box retailers and seeking out the unique, personal touch offered by small, local business. You can leverage this message by weaving yourself into the fabric of your community. Canadian yoga apparel retailer Lululemon has enjoyed explosive growth thanks to their ability to do just this. According to their website, “A Lululemon store is so much more than a place to shop. It’s an education centre, a yoga studio and a meeting place. It’s a local hub for educators, ambassadors and guests to gather to learn, sweat and connect. It’s our lifeline to our communities and the soul of our company.” Lululemon uses free events to make people feel that they have a sense of ownership over the brand, and you can too! Getting people through your door is 90% of the battle and event marketing definitely can bring in crowds.
2. Just the basics—I’ve used a compound miter saw, circular saw, jigsaw, band saw, router, table saw, drill, finishing sander, belt sander, Dremel, oscillating multi-tool, bar clamps, and a Shop-Vac. I haven’t used a planer, jointer, or lathe. I’ve never owned a table saw but have used a circular saw or improvised with a router for a few long cuts.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.
In our Complete Coffee Shop Startups Kit, we spend a good amount of time discussing your health department requisites, your coffee equipment, and even the design of your coffee shop. Since this makes up a significant bulk of your startup costs (equipment, space requirements, etc.), we recommend that you spend an extra couple of hours strengthening your knowledge base with listening to our audio interviews.

Hey, I hope we’ve been able to share with you some ideas that you can use if you’re thinking about building a workshop or any type of hobby room or just about any room in your house that you can get this kind of enjoyment out of. We have a lot more details on this shop as well as other things you need to consider if you’re building a shop on our website at todayshomeowner.com. hey thanks for being with us. 

​One tool that has been notably missing from the earlier builds is a router.  There are so many reasons to own a router that I am not going to even try to list them.  But if you want to get the creative juices flowing, take a look at this Pinterest page.   The important thing to know is that this versatile tool can help you accomplish a number of tasks, everything from finishing edges to cutting dove tails.  
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.

Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.
A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.
In a woodworking shop, lumber storage is key, and it’s best to design shelves or racks that are about 50 percent larger than you think you need — you’ll almost certainly acquire more materials as the years go on. To maximize a small space, use walls by mounting shelves to the ceiling and purchasing a sturdy step ladder to help you reach things. A wall covered in standard pegboard and outfitted with hooks allows you to customize hand tool storage and keep your most-used hardware within easy reach.

There are certain sayings that hold true and when buying clamps and measuring equipment parting with cash for quality make sense. But which clamps? G, F, sash, spring or strap? There are so many clamps and measuring tools available. Let the project decide which ones you need. As a reassurance, our Axminster Trade Clamps come with a lifetime guarantee, so this is one investment that literally lasts that long.
Great video Marc. I know I’m not the first to bring up the reverb in the shop. However I don’t think addition of rubber floor and cabinets will change this much. Furthermore, sound panels look very clunky in my opinion too, but may be necessary above some machines? Materials like drapes and carpet strategically placed can also do wonders, but I don’t know how practical that would be in a wood shop.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Then there are material considerations, such as how to bring full-size sheets of plywood home to cut down to size (you don't). And safety and cleanup are two more concerns: Proper ventilation and dust collection, a cinch in a larger shop, can be quite a challenge (and a potential health hazard). Nevertheless, you can set up a great wood shop in a small space, and we'll show you what you need.
So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.
The threshold area, also known as the "decompression zone," is the very first space that prospective customers step into when they enter your store. It typically consists of the first five to fifteen feet worth of space, depending on the overall size of your store. It's also the space where your customers make the transition from the outside world and first experience what you have to offer.

The subfloor provides a stable layer - basically a sheet of plywood - for your floor to sit on. You’ll see a lot of van build videos on Youtube showing a ¾” subfloor, but that thickness just isn’t necessary in a van. The thicker the subfloor, the higher the cost and weight, and the more valuable interior space it takes away. We recommend using ¼” plywood for your subfloor, which is plenty thick enough for a van.


After you are done narrowing down your list of business goals, you are now ready to plan out when they will be accomplished. Just remember, nothing is set in stone so if you need to remove or add something to your business goals later down the road, that's okay. It happens to me ALL THE TIME. Sometimes our priorities shift or things didn't go as planned and you need to make changes. 
One of the things that draws me to the online woodworking community is amount of passion people show are willing to share. Your shop build is a fine example of your willingness to let us in on your passion. You could have said “I’ll be back in a few months when its done” and most of us would have waited but instead you turned it in to a summer of updates and dream shop discussion. Thanks!
Because workshops are rough and tumble places, the right fan for the job will have an industrial-strength motor and adjustable fan speeds. Easy-to-clean metal blades and a fully encased motor housing are also important features, especially if your shop tends to fill up with sawdust, wood chips and other fine debris. That extra layer of protection will help the fan motor last for years instead of being damaged by particulates.
Expanded polystyrene (EPS) is an open-celled foam board (think styrofoam) that is the cheapest of all the foam boards. It does work, but we generally don’t recommend using EPS in your van. It insulates less than XPS (R-4 per inch), and the gaps between the foam cells allow moisture to penetrate, which degrades the insulation over time. Polyiso and XPS are much better choices for a slightly higher cost.
This holds a lot of stuff but mainly our handheld power tools, so it needs to support a lot of weight. Any shelf in a workshop will probably wind up supporting more than you initially planned so build it as strong as you can and don’t scrimp on the materials or the fasteners you use to hang it. Now the next step is to install our recycled cabinets that will line the wall under the shelf. Now these cabinets are a little plain but that should work great for a shop like this. Even if you don’t own a remodeling company you can usually find these things pretty inexpensively from salvaged warehouses which recover them from renovation projects then resell them to the public.
It is also essential to take a lean, data-led approach to choosing a business space. The average length of a commercial lease has dropped over the last few years but is still often well over five years, so the absolute last thing you want to do is rush into a signing and get locked into a bad situation. There are so many ways to test the viability of your business idea before you over-invest and sign a full-blown lease agreement.
A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
As Kizer & Bender always tell retailers: Put it on paper. If you haven’t settled on your store layout—or even if you have—the first thing you need to do is work your plan out on paper before you start moving things around in your store. Putting it on paper helps give you a clearer picture of the desired result and any potential issues before getting started. Remember, many small retailers find that a mix of floor plan and layout styles works best.
In addition, if your aisles aren’t wide enough, you could be subject to complaints or lawsuits under the Americans with Disabilities Act (ADA). The ADA requires you to have aisles that are at minimum three feet wide. If you’re reported to be non-compliant, you could be fined if you don’t widen your aisles and remove obstructions. Learn more about the ADA’s retail store requirements here.
Hi, I have looked through pictures of the shop books. What I am interested in finding is a book with layout design options. I am ready to build a new shop for myself and want to put dust and electrical under the slab. Best layout designs would help me to figure out how to layout a shop that is aprox. 28'x 36'. Is there a book that has this type of information.

What about when you’re camping? Well, most campgrounds (including many free National Forest and BLM campgrounds) have some sort of bathroom situation. If there’s not an actual running water bathroom, you’ll typically find pit toilets (aka vault toilets), which are basically much nicer/cleaner permanent porta-potties. We also recommend picking up a good poop shovel for those times you’re camping in a wilderness area without bathrooms.

The Best Prices for Tools – Ralph shows you where to get the beast deals for the tools and equipment you need. You could buy them yourself from popular outlets like Home Depot, Lowe’s, and Amazon, but the Ultimate Small Shop guide shows you where to get these tools and equipment at cheaper prices. Of course, cheaper isn’t always better. These aren’t just cheap tools that are ineffective. Just good value for money on good tools.
I look at these workshops and wonder if I'm the only woodworker that has other hobbies that require shop space. My one car garage serves for woodworking, motorcycle storage and maintenance and home repairs. I have a floor standing drill press, Band Saw, 10" cabinet saw, lathe, 6" jointer, 3 tier tool chest(automotive tools only) 4' workbench, mortiser on a pedistal, grinder on a 16" square storage cabinet, and a roll around 40"x22" cabinet that hold my miter saw, portable thickness planer and other storage. Luckily I have an attached shed where I can keep my dust collector and compressor and have them plumbed into the shop. Right now my snow blower also resides in the shop where otherwise my 450cc KTM off road motorcycle would. I need to step outside in order to change my mind so please stop teasing me with these to die for shops. Paul
Now, photographs or video tape will also be very useful especially to pass along to your insurance adjustor. Now the problem is this documentation won’t help you at all if it’s lost or destroyed so consider saving your information electronically. Take your photos with a digital camera and create a list of all your valuables, and save both in a computer file. This file can be saved to a disk you can keep at work or upload it to a website that you can access it from anywhere including your home.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
Once you’ve got that, you’ll want to familiarize yourself with your tax obligations as a employer, including providing required employee benefits such as social security and workers’ compensation. As an employer you are also responsible for withholding federal and state taxes from your employees’ paychecks. What’s more, you are obliged to ensure all withheld tax is forwarded to the government within a defined time frame (usually a matter of days after the paycheck was issued). Failure to do so can result in a fine.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.

The tablesaw—This tool is the backbone of nearly every shop, and for good reason. It allows unmatched precision in ripping parallel edges and crosscutting at a variety of angles. Most woodworkers find it crucial for the basic milling of stock. It is also suited to many joinery tasks, easily producing tenons, box joints, and—with a reground blade—the tails for dovetail joints.
Just stumbled across your article and it’s right on time as I am about to launch a special events venue (ballrooms, meeting rooms, outside garden area, outsourced caterer, etc). Not sure what type of zoning this business falls under. I read that zones are usually for office, retail, industrial and leisure. Any idea what type of zone I should be looking for? Also first time trying to get a commercial space for this type of business, any specific suggestions?
There’s a lot of blood, sweat, tears, and cash that goes into starting and running your own small business. One of the primary benefits of incorporating is that it limits the liability and risk of any losses your business may accumulate along the way. In other words, when you incorporate a business, you are typically not personally responsible for business debts. So if life happens and something goes wrong, as long as you and your business are not legally considered the same, your house, your car, and your goldfish are all safe.
Disclaimer: The content on this website is provided for information purposes only, and should not be interpreted as professional advice. You should perform your own research and consult with a qualified professional. Individual results may vary. Through this website you are able to link to other websites which are not under the control of discountra.com. We have no control over the nature, content and availability of those sites. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.
Now, we’ve already applied some resurfacer to fill up some of the deeper holes and after that dries overnight we’ll use a floor leveling compound tomorrow morning to really smooth everything out. Leveling compound is more fluid than the resurfacer so it flows into all of the low spots to even out the surface. Now, this won’t look like a finished floor when Tim’s done but it should do the job for our shop. Now, while he wraps up this Emily has a Best New Product that might be a great addition to your workshop.
In an indoor or basement shop with industrial carpeting, lay down inexpensive laminate flooring to make your life a bit easier at the end of the day. Be sure to anchor the panels or place a large rubber mat beneath to keep them from sliding over the carpet. (Covering up your carpet is even more critical if you want to go beyond wood and work with a material such as aluminum in your indoor shop; metal shavings dig into any kind of carpeting and are incredibly frustrating to clean up.)
We have a 5-gallon clear plastic Hedpak container that our sink drains straight down into. We really like this container because it’s clear, which means we can easily see how full it is. With 5 gallons of gray water capacity, we only need to empty it every 3-4 days. Dumping is easy - just remove the tank from under the sink and pour it out into an RV dump facility or other approved area.
The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself).
Nicole and I decided not to go public with the cost of the build. Although we are very open about most things, we are a little uncomfortable about making an expenditure of this magnitude public knowledge. Furthermore, unless you live in the Phoenix area and plan on building the same size shop with the same patio and with all of the same finishing touches and labor requirements, the price isn’t all that helpful to you.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
You’ll also sometimes want to walk a property with a licensed contractor. This is because some commercial spaces require lease build outs, which are necessary additions or improvements to the space. Build outs can be fully or partially covered by the landlord. It’s important in this scenario that you get an accurate renovation estimate and negotiate a build out into your lease.
These new companies no longer charge crazy upfront fees, moving instead to what’s known as a “SaaS” monthly subscription model, often with a free trial period. Therefore, the risk of trying a new product is greatly reduced, as you are required to pay little or nothing upfront. Even Microsoft announced in 2015 that they would be moving their flagship product, Microsoft Office, to this pricing model.
You can see in this step how I notched each rafter to fit more securely to the walls.  I also used a metal hurricane strap to secure each rafter to the wall.  Even though this was not required by code, I felt my tools were far to valuable to be left to chance over such an inexpensive solution.  The walls are a simple board and batten system.  The 1x3 trim covers the joints of the 4x8 OSB.  They make much more high quality sheets goods to use as siding.  However, the cheapest I found was $35 a sheet and the OSB was about $5 a sheet.  I sealed the OSB and painted it with exterior paint.  If I run into problems in the future, I can just add a second layer of more durable material or simply have siding installed.  It has held up very well over the past couple years and I see no need to spend more money on it now.
But if you want to do a lot of stealth camping in cities, a cargo van is your best option. There are so many of them on the road that people just don’t notice them, and they have a lot of floor space to play around with your perfect layout. But if you don’t plan on stealth camping and you value storage space and headroom, there may be better choices.
They say nobody ever started a small business out of a love for numbers, but if you really want to stay the course, you’re going to want to fall in love fast. It’s only by keeping detailed accounts and tracking your business’ numbers over time, (net sales, cost of goods sold, and average transaction size) that you’ll start to gather the actionable insights you need to make intelligent business decisions. 
×