We've written about routers on the site before and my favorite is the Bosch 1617. It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table. On top of that, it comes with a plunge base which makes it significantly easier to use handheld. The package clocks in at ~$190.
Remember that you must allow three feet of pathway space between all display units to meet Americans with Disabilities Act (ADA) requirements. But customer comfort is more than a requirement. Studies have proven, time and time again, that customers do not like to be jostled when shopping. Allow generous pathways between fixtures. Experts recommend three feet, six inches, so customers can move freely, examine products, and carry items to your registers. This will keep customers happily browsing in your store and you in good standing with the ADA.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
Another great source of store design inspiration is your product vendors and their line reps. After all, your success is their success, so they’re usually happy to share store design and merchandising ideas. Many provide retailers with free or low-cost branded display units, too. Some line reps will even assist you in product mapping your store, display setup, and replenishment. It never hurts to ask!
Hey Melody, thanks for the email. I’ve traveled through some extremely humid areas (Central America)… I’m taking it that your canopy does not have a headliner? That in and of itself helps a great deal. Personally I would be hesitant to put holes or van roof vents in my cap, but that may be what you want to do. I would try sleeping with a portable personal fan first and see how that helps with the condensation issue. For me it worked wonders while sleeping in those hot and humid environments. I ran mine off the inverter connected to my secondary battery.
State Parks/Developed Campgrounds. Every once in awhile, it’s kind of nice to stay at a state park or other developed campground - and a big reason why is that they have showers (and sometimes laundry, too). This is what we’ve done most often when we need a shower on the road. Many state parks also have small day use fees if you don’t want to actually camp there.
A dust mask or respirator will protect you while you're working, but won't do anything to protect you or your family from suspended particles still in the air. For this reason, an air filter is an absolute must if you work with woods indoors (I know of guys who sneezed out sawdust after working too long without an air cleaner). It's possible to make your own air cleaner out of box fans and furnace filters, but retail air cleaners will usually be much more compact. If you go that route, we recommend Wen 3410 3-Speed Remote-Controlled Air Filtration System for smaller shops.
In my opinion, the best shop space is a flexible one. I know many folks expected that after setting up my shop so many times, I would be able to design the PERFECT shop space including a finishing room, a dust collection closet, and even some internal walls. But the truth is, the most important lesson I learned over the years was to expect change. My shop is not a static entity. It is more like a living breathing creature that adapts, evolves, grows, shrinks, and changes configuration. Committing to an internal spacial arrangement too early could yield disappointing results. This is why you won’t see me placing dust collection ductwork in the floor. I need to work in a space for at least a few months before I can be confident in my initial setup. Even then, I fully expect things to change at some point. If I made too many restrictive and/or permanent decisions ahead of time, these changes could be difficult or impossible to implement. So my best piece of advice is to forget about the concept of perfection. Instead, focus on flexibility. The ideal shop, in my mind, is little more than 4 walls, a roof, and a butt-load of outlets and lights. So here are some of my basic general goals for my new shop space.
Hi thanks for the info. I’ve got a 2009 tacoma and went with a simple, no screws elevated system. I’ve also got a mx series ARE shell with rack rails so I’ll probably take too much stuff now. Oh well. My question is: how did you attach the plywood to the life gate? My carpentry/construction skills are best illustrated by the “Homer Simpson spice rack”. You used the existing holes in the tail gate, but did you put the tail gate cover back on the tail gate and put the plywood over it and screw thru both or ditch the cover? Thanks
Alternately, a detached shop can often be located closer to your property line and offers you a bit more freedom in terms of the type of foundation you can use. It may give you a sense of welcome separation from your home and open up yard space or allow a deck on the back of your house that would otherwise be lost behind your shop. In an urban setting, if you would like to have a wood stove in your shop you may find it more challenging to find an insurance carrier that allows one in an outbuilding. Also, outbuildings can be subject to more stringent height regulations than additions.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wiring for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to finishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a programmable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.