I live in Northern Va and have the same concerns. I save those little silica gel packets every time they come in a new product and put them in my tool drawers. I also salvaged a dehumidifier from a neighbor that I need to repair and set up in there. I use the wall mounted AC in the summer to keep it cool enough to work in there. Although I haven't gone back yet to insulate the ceiling, it stays really cool in there if i want it to be.
In as much as I am a clamp freak, I needed some way to organize clamps without spending a mint on brackets. In our previous house we had a number of glass shelves –which I didn’t plan to put up here. But, the brackets were great – I laid in two tracks next to each other, then took a pair of the shelf brackets, cut a piece of 9/16 x 9/16 x 3 inch pieces of wood – put the wood between the brackets, shrunk wrapped around the brackets and wood, and came up with some really stable clamp hangers.

I don’t own a dog, but I have taken my buddy’s two dogs out with us to the trailhead at least. Not sure that I have great recommendations for how you would go about living in the truck with your dog. All we really did was lower the large wooden deck to the bottom position, throw down some soft doggy beds and pillows, then cover it all with a giant blanket which also covered like the side bins to keep dog hair from getting all over. It was nice and cozy for the dogs while driving down the road. Then we just put packs and other gear on/in the side bins. We used some big metal clamps to secure the blanket to the side bins and keep it from falling down or sliding around. I would think avoiding any carpeting would be a good bet, just go with blankets and things than can be taken out, cleaned, and you can sweep out the back.
Well I think I’ll have plenty of light once we get all of 24 bulbs in place. I’m really glad I saved those old fixtures. Hey another thing we’re reusing, and I’m really glad I saved, is these old cabinets that we took out of a kitchen renovation a couple of years ago. This will be perfect to serve as our base cabinets so that we can build our sturdy countertop on this side of the shop.
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.

I’m currently in the process of building my own small shop and I almost didn’t watch this video because I was afraid I might become too jealous. I wasn’t. It made me realize that a good shop is worth waiting for and that I don’t need to be discouraged when things aren’t moving as quickly as I hoped. Thank you for the inspiration and congratulations on your new shop, you deserve it.
If you want the ability to cook inside your van but don’t have a whole lot to spend, your best option is the Coleman Classic propane camping stove. For about $60 you get a sturdy and reliable 2-burner stove that runs off of replaceable 1-lb propane canisters. We’ve seen many people using these out on the road, and they do the job very well. Coleman has hardly changed the design of these stoves for decades, so you know they’re doing something right.
It is also essential to take a lean, data-led approach to choosing a business space. The average length of a commercial lease has dropped over the last few years but is still often well over five years, so the absolute last thing you want to do is rush into a signing and get locked into a bad situation. There are so many ways to test the viability of your business idea before you over-invest and sign a full-blown lease agreement.

Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.


What I have done in my man cave of a shop is to install above my finishing table a strip of track lighting where I have fixtures ranging from the typical bright white incandescent (typically around 4700k) all the way to the average halogen spot that I figure someone would use with an art piece (normally around 3700K). this allows me to point each light and view my piece and finish under varying light conditions to judge whether or not I prefer a particular finish or not. It also helps in photographing items (though filming is a whole nother story, I still have my 5400k T8 overheads for working).
Note: This article will not include considerations for costs by independent developers or offshore firms. As I have written about cost differences in previous articles, those costs vary widely. Instead, this app cost resource focuses on what it would take to have a quality team of professionals build different kinds of apps. That could be done in-house, by building your own team, or by contracting a third party agency like Savvy Apps.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
The cheapest and easiest way to supply fresh water to your sink is with refillable plastic water containers. There are many styles available, including jerry-can style containers, the extremely common Aqua-Tainer, or standard 5-gallon water cooler jugs. Which one you go with really depends on personal preference and the dimensions of your kitchen cabinets.
As far as the batten, your actual question..haha. There has not been any moisture or rain make its way through. However, I did caulk all of those joints before I painted. I also made sure I primed all the exposed edges, especially the bottoms of the osb sheeting. You could probably put some pvc j channel along the bottom to prevent rain splash from absorbing up into the end grain. Just make sure you give a way to drain any water that makes it in the j channel. Does that make sense?
But here’s a quick back-story so you know how things went down. The reason I moved my shop so many times was because the sale of our old house fell through at the last minute. This is the house with the original Wood Whisperer shop/garage. We took the house off the market to recuperate and wait for the market to improve. In the mean time, I decided that I should probably make the best of the shop space that I was already paying for, so that’s why I moved my tools back there. When we eventually put that house back on the market, it sold on the first day. That was a BIG surprise! While we weren’t financially (or mentally) ready to build the new shop, I wasn’t about to lose a chance to get that 2nd mortgage gorilla off my back. So all of our resources went into the sale of the old house and the purchase of my mom’s new place. Truth is, there really wasn’t much left to put toward the new shop. Thanks to some financing wizardry, we made it work. But let’s just say I’ll be paying this off for quite some time!
To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.
“Walk past your Decompression Zone and look to your right. The first wall you see is called a Power Wall, and it’s another key merchandising area. And because it’s one of the first things shoppers see after looking or turning right, it’s a perception builder. Use your Power Wall(s) to display important departments as well as new and seasonal items to create vignettes, tell product stories, and to feature high-demand and high-profit items. (Note: Your store has more than one Power Wall. Stand in various places throughout your store and look around—the walls that stand out are your Power Walls.)”
When registering your business name you should also consider whether or not you have plans to expand your local business nationally or online in the future. Registering your business with the state does not offer brand protection beyond the state it is registered in. For example: If Bob’s Bike Shop is registered in New York, no other business will be able to use that name in that state. However, someone in Idaho can still register their business as Bob’s Bike Shop. If you have aspirations that look beyond Main Street, USA and would like the option to expand nationally or on the web, you should consider trademarking your business. When you trademark your business name, it makes it a lot easier to recover property that infringes upon your brand. For example: If Bob’s Bike Shop in Ohio purchased the domain www.BobsBikeShop.com but Bob’s Bike Shop in New York trademarked that name, legally Bob’s Bike Shop in New York has the right to file a domain name dispute to get the domain name back from it’s current owner.
If you want the ultimate vehicle to customize for your DIY van conversion, the Sprinter is the van for you. They have enough headroom even for tall people to stand up, and enough interior space to design any kind of layout. They also typically have diesel engines, which means greater fuel efficiency and engine life (many diesel Sprinters have been known to make it past 400,000 miles). If you think you’ll be doing a lot of off-roading, the Mercedes Sprinter also comes in a 4x4 version.
Make sure the room or building you are planning to utilize has sufficient lighting and electrical outlets to allow you to see what you are doing, and to work without excessive extension cords. You should also remember that many tools require a fairly substantial amperage to operate, so you need to make sure the wiring is capable of handling the loads. 20 Amp circuits will work for ordinary 120V tools, but air compressors and welders may require 40 Amp, 220V circuits.
“Zone design successfully helps shoppers locate what they want while exposing them to products that enhance the ones they are buying. Increased transaction totals are a natural byproduct. Products are categorized by use into Zones, such as ‘kitchen/cooking,’ ‘entertaining/dining,’ and ‘home decor,’ with inventory range and stock levels determining the size of each Zone.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
Well, I thought about that I don’t want all that dust to kind of infiltrate everything else in the building. So actually instead of putting in some kind of dust collection system, I thought that I would probably just put a nice shop vac here. And then I have room that I can bring some hose back behind this column and then you know if you’re sitting here working on something we can have adapters that go right into a miter saw or right into a sander or have a little outlet more or less to lay up on the counter that would collect all of the dust. And the same thing could happen on any of the work we do out here.
I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.

Use the scrap piece of plywood to map out the angle for the speaker stand legs. Decide the height you want for the base of the speakers, and make a mark on the plywood (32 in. for us). Mark the depth of the speaker (13 in.). Lay the 1x4 board assembly on the plywood, lining it up with both the corner of the plywood and the 13 in. mark from the edge. Scribe along the 1x4 board assembly, take the assembly away, and find your angle with a protractor or speed square (17 degrees for us). Cut that angle onto one end of the 1x4 board assembly.
The small apparel boutique pictured above really nails these traffic flow details! A roomy entrance offers clear sight and travel lines to eye-catching power walls on the right, and an inviting seating area towards the back. These lure customers into the store with the promise of treasures and comfort within. The shop even has a left-side checkout midway back. Someone really did their customer behavior homework on this retail store layout.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.
We've written about routers on the site before and my favorite is the Bosch 1617​.  It is light enough that you can control it when using it handheld, yet powerful enough that it won't have any problems when you mount it under a table.  On top of that, it comes with a plunge base which makes it significantly easier to use handheld.  The package clocks in at ~$190.
Food in bear country… When I was in *real* bear country, like in the Sierras, I always kept my food and scented items in the provided bear lockers. Any of the trail heads or camping areas will have bear lockers. Other than that I never really worried about. Just kept it in the cab, yeah. But the Sierras were the only place I went with any considerable bear problems.
Hey Marc. Just wanted to send a huge congrats your way for this milestone. It’s been pretty awesome to follow you on this journey since I discovered you on iTunes some 5 or 6 years ago. Mad props for what you’ve done to grow and enhance the online woodworking community as well as woodworking as a whole. I think with todays generation (as well as future generations) growing up behind a computer, the work that you and the rest of the podcasting world do will go a long way towards bringing new people into the craft. I hope that in the future you are able to start a series of videos showing how you introduce Mateao to the craft. Keep up the awesome work!
Since your business name is often the first thing potential customers will see or hear, think of it as one of your key tools for leaving a lasting impression. The right name, like a firm handshake, can play a role in your brand’s perception. So make sure it’s strong, catchy, and unique, but most importantly sends the right message about your business.
I like how you thought out the lighting for you shop. I have 6ea.6 tube T-8s but find 6500K bulbs but find lighting for filming is not that good, seems dark to me I use a Canon T3i its a decent camera I do have a row of windows in a 16′ garage door and aman door with a window on one end and a small window at the other end of my shop. Any idea what the issue may be?Could I still be getting too much light?

Up until about ten years ago, if you were in the process of starting a small business and wanted to use all of the technologies listed at the start of this section, you would have needed to take out a second mortgage to cover the bill. Investing in retail technology has historically involved expensive hardware (including an in-house server), large upfront software costs, and hefty ongoing bills for customer support or repairs when things went wrong. Innovators were targeting large-scale enterprises like Coca-Cola, not local mom and pops, so the packages and price points were designed to match.


DeAnna says that in general, the front left of a retail store is a good location for the checkout counter, like the one above. Shoppers naturally drift to the right when they enter a store and tend to loop around the store, leaving on the left side. So, a checkout at the front left of your store puts it your customers’ natural exit path. Plus, it doesn’t distract them from shopping as they make their way around the store.
5. Move beyond shelving. Shelving can be a very effective way to make the most of your wall space, but you can also find more creative, space-saving ways to display products. Instead of a big floor case for jewelry and other small items, Langdon recommends buying an old painting in an ornate frame and stretching the canvas in linen to create a giant corkboard to pin products on. At Poppyseeds, tea towels are displayed on an antique wrought iron headboard propped against a wall. The headboard takes up little space and adds character to the store.
The subfloor provides a stable layer - basically a sheet of plywood - for your floor to sit on. You’ll see a lot of van build videos on Youtube showing a ¾” subfloor, but that thickness just isn’t necessary in a van. The thicker the subfloor, the higher the cost and weight, and the more valuable interior space it takes away. We recommend using ¼” plywood for your subfloor, which is plenty thick enough for a van.
Because two-sided market apps lack the specificity of on-demand apps, usually more features need to be built. More significantly though, it's much harder for a company to build each side of the market. Uber, for example, is focused on driving. Angie's List, on the other hand, has hundreds of different kinds of service providers. If it wasn't clear from the examples, both on-demand and two-sided marketplaces also have a geographic component. This means that they often start in one area or a subset of areas like Uber did in San Francisco.
Can you outfit your shop with all the necessary hand tools for just $100? Christopher Schwarz says you can, and he’ll show you how to do it in this article. Take Christopher’s shopping list to the flea market and come back with everything you need for less than you’d spend on one new hand plane. You can do all your woodworking with hand tools, and this article from Popular Woodworking will equip you with everything you need.
as the name implies--I have no qualms about using castoffs, trash or clearanced items in my shop--I have a 3and one half car garage that I can't get a vehicle in(even tho I like to change my own oil, etc.) because I have so many interests like woodworking, metalworking, plastics, machining, machine building, carpentry, etc. we have to store our kids furniture somewhere, as well as some of our own... You involve a welder, 2 tablesaws, bandsaw, planer, lathe, drillpress, benches and benchtop tools--not to mention storage of materials and I've got a collosal mess that I may never get straightened out!!!--Did I mention room for the woodburning stove I heat it with??? I am always appreciative of these "dream shops" I see in FineWoodworking"
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but out­side the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials move­ment. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
In every aspect when starting your small business you should be mindful of making careful, prudent decisions about the allocation of your potentially limited funds — tracking precisely the cost of goods sold (CoGS) against sales to ensure profitability. Every dollar spent is tracked and accounted for, either as an essential cost of doing business (rent, employees, etc.) or as a cost of inventory that will result directly in profit.

Because two-sided market apps lack the specificity of on-demand apps, usually more features need to be built. More significantly though, it's much harder for a company to build each side of the market. Uber, for example, is focused on driving. Angie's List, on the other hand, has hundreds of different kinds of service providers. If it wasn't clear from the examples, both on-demand and two-sided marketplaces also have a geographic component. This means that they often start in one area or a subset of areas like Uber did in San Francisco.


Once you know your top priorities, you can start thinking about the space each element can take up and where it should go. It is like putting the pieces of a puzzle together when you're working with a small space, so don't get frustrated if it doesn't work out right away. And know that you'll likely have to make some sacrifices. Play with a few options, and choose the one that works best for your situation.
The on the go mode is ideal for when I’m just driving all day and need to pull over and get some rest, be it in a parking lot, a residential cul-de-suc, or wherever. I usually toss a couple of items in the cab of my truck and crawl into the “coffin” sleeping arrangement for a quick night’s rest, but I can also crawl in without placing anything in the cab.
There are many inexpensive alternatives lying around the house or at your local store you can use to create a Halloween theme that will impress all your friends.”One of the most popular party favors is a framed picture of the party guest taken at your kid’s party. He or she could be showing off a silly hat or party costume, performing an outrageous party game stunt, or wearing a face full of frosting and ice cream. Having party guests create their own make-and-take frame to display this memorable photo makes it an even greater treasure for the memory box. Start with a plain square of cardboard with an opening the size of your picture. When the decorating is done, Ultimate Small Shop Reviews simply glue the picture to the back of the frame. Why not turn that Cooking Interest, Comic Book Collecting, or Your Retro Clothing Collection Into A Home Based Business Venture! Most people enjoy hobbies they have pursued with great enthusiasm for years. Even though they may find their leisure activities fulfilling and enjoyable they never imagined making money with a fun hobby! Are you one of these gifted individuals? These talented individuals might have a passion for sewing fabulous original wardrobes, marvelous hand knitted items, furniture making, creative paintings, photographs, jewelry art, greeting card design, doll making, original toys, baby clothing, candle making, quilting, calligraphy, fancy soap making, about anything you can imagine! Crafting is actually a great way to start a home business on a shoestring. You might want to start on a small scale by offering your creative work to friends and family. Later on, once you have enough products, you might decide to rent a booth at local flea markets or crafts shows to display your work. As you may know, the Arts And Crafts Industry Is Enjoying An Amazingly Phenomenal Popularity. People are eager to purchase hand made clothing, furniture, custom made keepsakes or jewelry. If you have the creative talent this is one business you should consider! A friend, Joyce, diverted her obsession with candle making into a thriving business. She started by selling her hand made scented candles to friends and neighbors. Word of mouth spread about her candles. Soon she was receiving enough orders to keep her very busy. Joyce throws house parties to sell her candles and also takes custom orders from ads she runs in local newspapers. Next, she plans to take her candles to the stores and malls in her area.”Today is life – the only life you are sure of. Make the most of today. Get interested in something. Shake yourself awake. Develop a hobby. Let the winds of enthusiasm sweep through you. Live today with gusto.”Our hobbies help us to relax and forget our everyday problems and troubles. We are all experts in one or more fields of our lives. Ultimate Small Shop program But I am sure that not everyone has a hobby that makes money for him/her (except, of course, if you love your job).Just imagine, wouldn’t it be great if you could have money making hobby? You could get involved even more with what you already love to do, you could treat your family and friends with the extra cash, or… even quit your current job that you probably hate.
Now I want you to create a spreadsheet or use my worksheets and write one major goal on the top. This can be the first goal you want to accomplish. Then I want you to list all the tasks you need to do (or someone on your team has to do) in order to accomplish this task. For example; let’s go going back to the goal of "Launching a New Website". The tasks you will need to do to get this goal accomplished are the following;

Now also we have some shelves that we built here above this, little cubicles like this work great to organize your workshop so you can have different tools or different supplies in the different little areas. And we’re about to install a very simple countertop. Now this is nothing more than just three-quarter-inch plywood and we decided to stain it instead of painting it, because you know it’s going to take a lot of abuse with all the pounding and the dings, and dents you’ll get in a workbench so staining it and then sealing it with a coat of sealer will probably hold up better than anything else. Now we’ll put another coat of sealer on it after we finish the front edge band and the backsplash and once all of that is complete, boy this thing is going to work nice.
As part of my antique restoration work I do a lot of faux finishing – hence the supply of stains and paints. Since I didn’t want to dust the house, the new shop is not connected to the house heat and air system. But, having just finished our first winter I now know the shop didn’t get below 45 degrees – and, the oven in the corner can make the shop toasty in no time at all.

In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
5. Move beyond shelving. Shelving can be a very effective way to make the most of your wall space, but you can also find more creative, space-saving ways to display products. Instead of a big floor case for jewelry and other small items, Langdon recommends buying an old painting in an ornate frame and stretching the canvas in linen to create a giant corkboard to pin products on. At Poppyseeds, tea towels are displayed on an antique wrought iron headboard propped against a wall. The headboard takes up little space and adds character to the store.
However, my guess is around $250,00 t0 $300,000. So as you say you will have a good mortgage to pay for. So excuse me for being nosy. I am retired and I have started setting up my shop in my two car garage. It is not insulated just bare walls and open ceiling. I am going to start doing some projects and will keep watching your shows. I was a Computer Engineer and although I liked my job i always had that desire to get back in wood working and now I am doing just that.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
Great video Marc. I know I’m not the first to bring up the reverb in the shop. However I don’t think addition of rubber floor and cabinets will change this much. Furthermore, sound panels look very clunky in my opinion too, but may be necessary above some machines? Materials like drapes and carpet strategically placed can also do wonders, but I don’t know how practical that would be in a wood shop.
It's true for large and small shops alike: Sawdust and chips get everywhere when you use power tools. Small home-woodworking shops are often in shared rooms and may be poorly ventilated. And airborne sawdust and particulates linger for a while before settling. It's a bad combination for human lungs, which are not fond of sawdust, let alone the types of chemicals found in plywood and other engineered materials.
Plywood comes in several different types, the most common being pine and lauan. We used ¼” lauan plywood for the walls in our van. Lauan is cheap, it bends easily, and in our opinion its grain pattern looks nicer than pine. Hardwood plywood like birch costs more than pine or lauan, it weighs more, and it’s more difficult to bend. This type of plywood is a great option for furniture, but we think lauan is a better choice for your walls and ceiling.
Woodworking isn’t just an overnight hobby, for most it’s a fun pursuit that lasts a lifetime. As your skills develop, the workshop becomes a place not just to build but to repair along the way. In a world where people are strongly influenced by consumerism, there’s a tendency to revert to a throwaway culture. But if you can fix before throwing away, then your tools start to make a return on their investment and have a bigger impact.
Many retailers are also opting for digital signage. While digital signage and display solutions are more of an investment upfront, they allow you to quickly and easily show customers sales, new products, upcoming events, customer reviews, and more. Mira Digital Signage is a popular digital signage option for small businesses that is easy to use and offers affordable monthly payments. Click here for a free demo.

Shop looks great Marc, I see the Clear Vue in the picture. I love mine, I used 8″ PVC for the main trunk line and came out of that with 6″ drops. It works great. I wound up building a collection bin instead of using a can, only thing I didn’t do was make the bin big enough. It holds more than the typical can but I still should have made it with more capacity. The 1800 with the 5 hp motor is stout.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
Unfortunately, the requirements across the country and across different industries are as varied as the bodies enforcing them. The only way to guarantee that your licenses and permits are all squared away is to seek out regulating authorities on the county, state, and federal level, as well as consult with the relevant industry-specific bodies for your business type.
I live in Northern Va and have the same concerns. I save those little silica gel packets every time they come in a new product and put them in my tool drawers. I also salvaged a dehumidifier from a neighbor that I need to repair and set up in there. I use the wall mounted AC in the summer to keep it cool enough to work in there. Although I haven't gone back yet to insulate the ceiling, it stays really cool in there if i want it to be.
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette pack­age. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provin­cial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effec­tively through your drawings that your structure will comply with the techni­cal requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:
Back in the 1970s and treeplanting in Oregon, I and Tony Lessa lived for two weeks at a time in the back of my 1954 Chevy PU. The canopy was just a simple shell with the board across next to the cab. After the fourth or fifth trip out in the season the accumulated funk was too much. You can imagine two hard-working guys in very muddy and cold conditions coming in after work with dirty wet gear. Pretty desperate circumstances but before Reagan trashed the treeplanting industry our coop ( Hoedads & then Second Growth) was making good money so we endured the hardships. It works for the young. Now, at 76, I find sleeping two of us between the wheel wells in a Dodge G. Caravan (seats removed) much too crowded. I think I will tent and the wife can have the van.
One practical note: Lots of retailers and restaurateurs are now engaging in event marketing in their business locations. Lululemon does in-store yoga on Sunday mornings, Barnes and Noble hosts author readings, and your local Italian restaurant may offer cooking classes. Think about all the potential use cases for your store and ensure that it is fit for purpose.

To help, I’ve pulled together 40 small business ideas for anyone who wants to run their own business. Use these as a jumping off point to spark your own unique ideas.And if all else fails, live the words of Airbnb Co-founder Brian Chesky: “If we tried to think of a good idea, we wouldn’t have been able to think of a good idea. You just have to find the solution for a problem in your own life.”
​In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts.  Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up.  A more economical approach would be to build your jigs as your projects demand them.  After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.
The standard option for a shop floor is a concrete slab. You’re probably not going to go to the trouble of creating a basement beneath your shop, although it is possible. The weight of most woodworking machines suggests that a con­crete floor is the most solid and durable substrate available. It has the potential to be used as thermal mass to store heat from your heating system or from the sun, but it can be tiring and hard on your body to be standing on concrete all the time. You can add a vapour barrier, 2x4 sleepers and a wooden floor above the concrete to ease the tendency of the floor to strain your feet and back, or you can add anti-fatigue mats in key areas where you’ll be standing for longer periods.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
Now if don’t have space for a dedicated workbench say in your garage you can build one that folds out of the way when it’s not in use. Simply mount a board to the wall to hinge the table on, then you can use some eye hooks and chain to support it. Now it won’t support a ton of week but it should be just right for a weekend project every now and then.
We use this fan for extra circulation when it’s hot, and to get the air moving when it’s cold at night and we have all the windows closed. We also keep it on for our dogs while we’re driving. There are cheaper 12V fans out there, but generally the cheaper the fan the more power it draws. The Endless Breeze is a great little fan, and it’s definitely worth getting for the added ventilation.
According to store design experts, this is the part of the process where store owners tend to put the cart before the horse. Once the floor plan is sketched out, store owners are quick to purchase and install fixtures, then fill them with product. Far too often, the fixtures chosen aren’t ideal for displaying a range of products in a particular space. Or worse, they don’t offer flexibility needed in valuable display areas that are constantly changing to house featured and seasonal products.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
I look at these workshops and wonder if I'm the only woodworker that has other hobbies that require shop space. My one car garage serves for woodworking, motorcycle storage and maintenance and home repairs. I have a floor standing drill press, Band Saw, 10" cabinet saw, lathe, 6" jointer, 3 tier tool chest(automotive tools only) 4' workbench, mortiser on a pedistal, grinder on a 16" square storage cabinet, and a roll around 40"x22" cabinet that hold my miter saw, portable thickness planer and other storage. Luckily I have an attached shed where I can keep my dust collector and compressor and have them plumbed into the shop. Right now my snow blower also resides in the shop where otherwise my 450cc KTM off road motorcycle would. I need to step outside in order to change my mind so please stop teasing me with these to die for shops. Paul
Make sure the room or building you are planning to utilize has sufficient lighting and electrical outlets to allow you to see what you are doing, and to work without excessive extension cords. You should also remember that many tools require a fairly substantial amperage to operate, so you need to make sure the wiring is capable of handling the loads. 20 Amp circuits will work for ordinary 120V tools, but air compressors and welders may require 40 Amp, 220V circuits.
It’s important that you have a fundamental understanding of what is making your business successful before you decide to expand. Who are your customers and why do they enjoy what you offer? Who are your suppliers and will they be able to deliver to your new location? What are your operating costs and will they be the same in a new location? A lot of small businesses start off in the suburbs of a town before making the move to a city’s business district, only to find that unexpected additional costs are swallowing up their profits.
There are some variances in the features and reliability of different model years, and differences between the Mercedes Sprinter, Dodge Sprinter, Ford Transit, and Dodge Promaster - so make sure to do your research. The Sprinter RV Conversion Sourcebook is an incredible resource on all things Sprinter (and van conversions in general), and it goes over all the options in detail.
As a retailer, it's possible to use furniture, displays, racks, and other tools to create a clear path for your customers through your store. This will vary greatly depending on the size and your general store layout. However, you know that most North American customers will naturally turn right — so, your next job is to make sure that as they do, they also continue walking throughout your store to gain the maximum exposure to your products. This not only increases the chances of them making a purchase, but a well-thought-out path can be a great way to strategically control the ebb and flow of foot traffic in your store. 
Well, all these years we’ve always planned on this being a nice little workshop, and now’s the time that we’re about to remove all of this and create a nice realistic, practical workshop. Not a TV workshop that just looks good, but one that will be perfect for us to use for some of the projects we have on the show, and again it will be used by our construction company for some of the projects they have.
Whether you end up looking at self-checkout counters, fancy lighting systems, special refrigerated cases, or any of a countless number of options, never forget that these are only tools to help accomplish your main goal. Your store needs to create an environment where customers want to be, where they feel comfortable and appreciated, and where that experience will prompt them to purchase (and hopefully encourage their friends to do the same). Equipment and technology decisions should always be made with your customers in mind.
We do not recommend using Reflectix to insulate your walls or ceiling. Without an air gap, the R-value of Reflectix is about R-1. Even if you have the recommended ¾” air gap next to the Reflectix, the R-value per inch is less than R-3. There are much more efficient and cost-effective insulation materials out there for these purposes - you’ll be better off filling the space with rigid foam board.

From a legal perspective, this lack of uniqueness doesn’t need to be a major concern. According to the rules governing business incorporation in most states, if you find yourself opening with the exact same name as another business, you can keep it as long as “your business and the existing business offer different goods/services or are located in different regions.”


Love the local history of your city or state? Consider becoming a tour guide. Sure, you’ll need to conduct tons of research to be able to do the job well, but that’s half the fun. Set yourself apart by offering tours that speak to a specific niche of your community’s history. Some tour guides offer historical walking tours of their town’s most haunted spots while others curate guided foodie tours for guests to get a true taste of the city.
You’ve probably considered what goods and services you’ll be offering, but have you researched the cost of sourcing your raw materials? How about the cost of turning those raw materials into your finished product? Do you understand how much you’ll need to charge for your products/services in order to cover the expenses of renting a space, paying employees, leasing equipment, and paying for permits and regulations? Moreover, have you considered if the answers to these questions will provide the kind of operating margin you’ll need to pay yourself a salary?
Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.
Once you have an idea of your store layout and a product mapping plan, it’s time to consider your store fixtures and displays. Fixtures are permanent—fixed—parts of your store such as lighting, counters, fixed shelving units, and dressing rooms. Displays hold product and tend to be movable, versatile, and customizable, like modular units, gondolas, tables, slatwall, and clothing racks.
Do you want to create the next great retail dynasty? Do you want to be Abe Froman, the Sausage King of Chicago? Or are you just looking for a simple local lifestyle business? Are you hoping to create a franchise model? Or do you see your local business as a testing ground for an ecommerce business? Your end goal will clearly inform your decisions, so it’s worth considering what it is early on.
Everything from the way the customer is greeted as they walk through the door to the way your products are presented following a sale matters. The smallest details can make the biggest difference. Early on when just starting your small business, you as an owner, will be able to exert a lot of direct control over these details. But as you grow, you will come to recognize the value of a well-trained and motivated staff.
First things first, the machinery is going to do the bulk of your work. Hand tool purists may argue differently but how many machines do you have in your home to make things easier? The same should be true for your workshop. Yes, there may be moments when you take a deep breath at the initial investment but if you’re looking at woodworking as a prolonged pastime then the tools will last you for years to come. Plus you’re not buying everything at once. Start small and build up your collection.
Composting Toilet: Nature’s Head Dry Composting Toilet. Much more expensive but also more pleasant and environmentally-friendly. Just drop your load and add some peat moss/sawdust, and your toilet will naturally break down your poop into compost. If the Nature’s Head toilet is out of your price range, you can also try making your own composting toilet.

Congrats on a very nice shop. Great video to capture the moments. I too have moved around from place to place (in the Army) and I have to make my shop work with what they give me for a house. I’ve done work out of a tool shed and I make it work becuase I just love working with wood. Once I retire and settle in one spot I hope to get something similar to yours. I’ve picked up a lot of ideas watching this build.

In the summer months, your windows will be one of the primary ways that heat gets into your van. Because of its reflectivity, Reflectix works great as a window covering to reflect radiant heat away from your windows. And, if you’re concerned about height in your van, layering Reflectix under your subfloor is a good way to add a little insulation (R-1.1) without sacrificing headroom.
Shops can range from functional spaces adorned with unpainted wallboard to beautifully finished, painted, and trimmed-out spaces. Ultimately, I think it depends on your budget and how important your surroundings are to your mindset as you’re working, or to your clients’ if they will be viewing your shop. If finishing your shop will improve the quality of the work that you will produce, thereby relaxing or inspiring you, or showcase for your clients the quality of the work of which you are capable, it may be a worthwhile invest­ment. A more finished space may also allow for activities like parties or even a weekly poker game (as long as drinks stay off the tools).
You’ve probably considered what goods and services you’ll be offering, but have you researched the cost of sourcing your raw materials? How about the cost of turning those raw materials into your finished product? Do you understand how much you’ll need to charge for your products/services in order to cover the expenses of renting a space, paying employees, leasing equipment, and paying for permits and regulations? Moreover, have you considered if the answers to these questions will provide the kind of operating margin you’ll need to pay yourself a salary?
Keep your air hose and fittings in one place and out of the way. Screw a coffee can onto a scrap piece of plywood. Attach a 2-1/2 in. riser block to the edge of the plywood and hang the entire contraption from a wall or work-bench. Drape your air hose over the coffee can, and store your fittings inside. It also works great for hanging extension cords. — Walter Barndt. Build an air compressor cart.
Shop layout is all about making the best use of space. Place your machines so that you have adequate “safe space” that you need to work around them. The “buffer area” beyond that is the amount of room you need to run large stock though a given machine, keeping in mind that buffer areas can overlap between machines. If you want to get more organized, buy some 1/4-inch squared paper, make scale models of each machine including the safe space around each, and place them on your model shop layout. Remember that buffer areas need to be long enough to put an 8' sheet through a table saw, or a 6' plank through your planer, for instance. I raised my planer, so that I can use the area above my router table to pass long planks through the planer – all it takes is some modelling, and a little shuffling, and you will find the layout that works for you. Each space will have chal­lenges; I had the area under the stairs that was wasted space, so I installed the dust collector there.
Hand tools offer the finesse and precision you just can’t get with anything else. There’s a sense of satisfaction you get from working the wood rather than machining it. After all isn’t that why you got into woodworking? Again there are a vast array of tools but narrow it down to a core range and you’ll have the confidence to complete a number of jobs.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
×