I want the shop to be big! Not only do I have a lot of tools, but I tend to frequently bring tools in for testing. As you probably know by now, I also do a lot of filming. So I need a space big enough to allow for full movement around most of the tools. My tripod has a pretty good-sized footprint and having more room allows me to get the best vantage point possible. More space will also allow me to stage larger pieces of furniture, whether for the show or for jobs I take on locally.
It does sag a little bit, but not worryingly so. As I mentioned, it often rests on top of the large plastic boxes I place underneath, and I put in a small wooden brace at the entrance. You could definitely build it slightly smaller, or put in a more substantive center brace — like a sheet of plywood that fits into the groove of the bed liner and is the exact height you want.
First, decide on wax you would like to start with, there are three different kinds to choose from Ultimate Small Shop paraffin wax, soy wax, and beeswax. Paraffin wax is most commonly used in candles, this wax is found at most candle making stores. Soy wax is all natural, made from soybeans, and cleans up easily with soap and water. Beeswax is all natural too, and making beeswax candles is often easiest because you simply wrap a sheet of beeswax tightly around a wick then seal it with your thumb, which means no melting is required. To begin, spread newspapers around the candle making area. First, you melt your paraffin or soy wax and it must be double-boiled. Usually, you place a large pot that is about half-filled with water on a burner over low-medium heat, place a melter in the water, then gradually place wax pieces into the melter. When the wax has melted, you can add coloring or fragrance as desired. To make molded candles, cut the wick two inches taller than you want the candle to be, then thread it through the hole at the bottom of the mold, then plug the outside of the hole with putty. Place a pencil or similar item over the top of the mold and tie the top of the wick to it, centering the wick. If the mold is cardboard, plastic, or glass, heat the wax to 130 degrees Fahrenheit. If the mold is metal, then heat the wax to 190 degrees. You can use a candle or candy thermometer to measure this. Ultimate Small Shop Pdf When the right temperature is reached, lift the melter by the handle and slowly pour the wax into the mold. Let cool for twelve hours then refrigerate for twelve more hours, then your candle is ready to be removed. To make votives and other small container candles, you can use pre-tabbed wicks by simply placing them in the center of the votive candle molds or containers, then pour the wax mixture over and let stand for twelve hours, refrigerating the votives. By the time your teen is in high school, you probably aren’t taking as many pictures of them as you used to. I have to keep reminding myself that I only have a couple of years left and no time to waste trying to capture fleeing teenage memories. You might be thinking that I’m really organized to be already working on scrapbooking my daughter’s high school memories. To be honest, I have a shoebox full of pictures of my daughter waiting for me to get to someday. But if I wait until “someday” to continue taking pictures because I already have so many pictures I haven’t done anything with, then my daughter’s teenage years will come and go while I try to catch up. I don’t want to chronicle every detail of my daughter’s life (nor would she want me to!), but I was trying to think of some memories that she might want to laugh about and maybe even treasure someday. Ultimate Small Shop Guide Woodworking So how do you do that without ending up with pages and pages of memories? I decided to do two large (12×12) pages (facing each other in the album) for each year of high school.
Concrete garage floors can work as a workshop surface, but over time they stain and you’ll end up tracking a lot of dust and dirt into your home. An epoxy floor finish is easier to clean and can also provide extra grip. For a softer surface that will help your joints when standing a long time, check out those restaurant grade rubber floor mats or some durable options that include garage floor tile.
I like how you thought out the lighting for you shop. I have 6ea.6 tube T-8s but find 6500K bulbs but find lighting for filming is not that good, seems dark to me I use a Canon T3i its a decent camera I do have a row of windows in a 16′ garage door and aman door with a window on one end and a small window at the other end of my shop. Any idea what the issue may be?Could I still be getting too much light?
At a certain point, you may decide that it is time to move on from your business. Whether you’re winding down a business that just didn’t work out, retiring (and maybe opening that beach bar in Belize), or cashing in on the effort you’ve put into creating a lucrative enterprise, you will hopefully have established your end goal well in advance so that the time to strategically exit will be clear.
Ok Rob let me try again .I would suggest you sign up for a community collage woodworking class or a woodworking coop where you can use the tools you will need to build the kind of items you have in mind. You say you have used the tools you listed but that could mean only used them once or twice. If you have minimal experience with tools and woodworking that might be another reason to take a class assuming there is one available . Do you have a space you can use as a shop ,a garage,carport etc? As far as tools and equipment are concerned I think Knotscott covered it very well. I know your supposed’s said you couldn’t find tools on Craigslist or garage sales but those might be the place you can make an offer on a shop full of tools in the price range you trying to stay in possibly with some materials and other extras. It might even work to put a wanted wood shop full of tools in the tools section of your local Craigslist.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
For years my wife and I had agreed that we would one day leave Oklahoma for someplace we really loved. That day finally arrived last year when we found a home in Vancouver, Washington that met our dreams. Only thing missing was someplace for a woodshop. Well, there was a place, under a deck, but not a room. So, as part of the move we had a local contractor build a room that would one day be the wood shop. Fortunately there was already a door from the house into this area, and about half of the “walls” were there, in the form of concrete retaining walls.
A dust mask or respirator will protect you while you're working, but won't do anything to protect you or your family from suspended particles still in the air. For this reason, an air filter is an absolute must if you work with woods indoors (I know of guys who sneezed out sawdust after working too long without an air cleaner). It's possible to make your own air cleaner out of box fans and furnace filters, but retail air cleaners will usually be much more compact. If you go that route, we recommend Wen 3410 3-Speed Remote-Controlled Air Filtration System for smaller shops.
Love the local history of your city or state? Consider becoming a tour guide. Sure, you’ll need to conduct tons of research to be able to do the job well, but that’s half the fun. Set yourself apart by offering tours that speak to a specific niche of your community’s history. Some tour guides offer historical walking tours of their town’s most haunted spots while others curate guided foodie tours for guests to get a true taste of the city.
Of all the LED lighting options, puck lights are the most difficult to install. You’ll have to run wiring behind the ceiling/walls for each light. And you’ll need to cut a hole with a hole saw to recess the lights into the ceiling. But with some preparation and care it's not too difficult. We have full instructions for installing LED puck lights in our epic electrical post.
One example is testing your products and services for their desirability through ecommerce. It might turn out that your core product line will actually be much smaller than you originally envisioned. Equally, there are now a number of services (such as storefront.com) that will allow you to secure a pop-up lease in some incredible spaces, often for only days at a time. It might just turn out that your dream location isn’t as great as you originally thought.

Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.


Ideas on how to Improve your Workspace – We can all do with some ideas on optimizing workspace. The guide has a lot of information about how to improve your workshop to be more efficient and improve workflow. This includes the costs of improving your shop, as well as hacks you can do yourself to improve efficiency and storage space for less. You’d be amazed at what you can do with even a small room. You just need someone to point you in the right direction.
When I’m working on projects in the shop, I often have my laptop close by so I can refer to an article or take notes. The craft table I’d been using was too low, so I got some pieces of 1-1/4-in. PVC pipe to slip over the legs. I measured the height so it was just right—no more aching back! The pipe pieces are easy to slip off when we need the table for potluck. — Donna M. Courie
Radiation is heat transferred through air or a vacuum- think the heat radiating off of a fire. In a van, the biggest source of radiant heat is your windows. Sunlight (radiant heat) shines in through the windows and heats up the inside of your van. Using a reflective window covering will help deflect radiant heat and keep your van cool. Reflective surfaces also help keep radiant heat inside the van during the winter.
Have a walk-through yourself and see where the visual cues guide you or get your staff, friends, or family to do the same and give you honest feedback. Don't forget to observe your customers and see what they're drawn to, what they avoid, and how they move, then match that with your intended design. If you keep resilient and keep your eyes and ears open, you'll be sure to create a retail design that's a win-win for both you and your customers. 

Sometimes you just know it when you see it. So always be prepared to capture pictures and take notes when you see store features that you’d like to try out yourself. And don’t forget the many online resources out there. Settle down with a cup of coffee and scroll through Pinterest for a treasure trove of store design ideas. Here’s a great board to get you started. Or get inspired by the many hip retail store designs on the Retail Design Blog.


Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.
Now I want you to create a spreadsheet or use my worksheets and write one major goal on the top. This can be the first goal you want to accomplish. Then I want you to list all the tasks you need to do (or someone on your team has to do) in order to accomplish this task. For example; let’s go going back to the goal of "Launching a New Website". The tasks you will need to do to get this goal accomplished are the following;
Of all the LED lighting options, puck lights are the most difficult to install. You’ll have to run wiring behind the ceiling/walls for each light. And you’ll need to cut a hole with a hole saw to recess the lights into the ceiling. But with some preparation and care it's not too difficult. We have full instructions for installing LED puck lights in our epic electrical post.

I don’t think you have run into this problem, but I have to deal with condensation in the cap as I live in a moist climate. I was thinking of an old van type roof vent with fan for active ventilation, or drilling holes along the side of the cap, inserting short cuts of pipe with fine screens (mozie land), and capping them. This way I could control for rain, cold, etc., but create some passive cross ventilation at roof level.


Now, some of the things we’ll be covering in this week’s show will be things that you can use around your house whether you’re an avid woodworker or not. We’re going to talk about a little fold-down workbench that’s perfect for maybe that little area you have in your garage or your storage building. Also the importance of building the proper surface to work on, lighting, dust collection, a number of other things I know that you can use, but I’m so anxious to get this stuff out of here. Within the area like this whether it’s in a business or home there’s plenty of stuff that just needs to go away. But there’s also some tough to decisions to make about what to throw away, what to keep and how to organize what you hang on to.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
The on the go mode is ideal for when I’m just driving all day and need to pull over and get some rest, be it in a parking lot, a residential cul-de-suc, or wherever. I usually toss a couple of items in the cab of my truck and crawl into the “coffin” sleeping arrangement for a quick night’s rest, but I can also crawl in without placing anything in the cab.
×