Food in bear country… When I was in *real* bear country, like in the Sierras, I always kept my food and scented items in the provided bear lockers. Any of the trail heads or camping areas will have bear lockers. Other than that I never really worried about. Just kept it in the cab, yeah. But the Sierras were the only place I went with any considerable bear problems.
“Your sales floor is a living, breathing entity that needs to change—frequently—in order to flourish. It’s the retailer’s job to make that happen. If your store is filled with the latest and greatest products, but your sales are in a rut, it could be because your customers are bored. They come to your store not just to buy; they come for ideas and inspiration. And they come to be entertained—even when they don’t buy anything, that experience is what brings them back.”
Disclaimer: The content on this website is provided for information purposes only, and should not be interpreted as professional advice. You should perform your own research and consult with a qualified professional. Individual results may vary. Through this website you are able to link to other websites which are not under the control of discountra.com. We have no control over the nature, content and availability of those sites. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.
It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.
When starting your small business, the type of business structure you choose will depend on three primary factors: liability, taxation, and record-keeping. Most small business owners begin their commercial life as a sole proprietor because it’s the easiest way to get started. In fact, if you’re in business and you haven’t taken any action to incorporate, you are most likely deemed a sole proprietor by default. You are entitled to all the profits of your business but also responsible for all its debts, losses, and liabilities.
When I’m working on projects in the shop, I often have my laptop close by so I can refer to an article or take notes. The craft table I’d been using was too low, so I got some pieces of 1-1/4-in. PVC pipe to slip over the legs. I measured the height so it was just right—no more aching back! The pipe pieces are easy to slip off when we need the table for potluck. — Donna M. Courie
A grid floor plan, also called a straight layout, is a very efficient use of both floor and wall space. With fixtures and displays running parallel to walls, a grid floor plan maximizes every inch of available floor space, including the corners. Grid layouts are easy for customers to navigate and for store owners to categorize. Plus, they offer plenty of end cap and feature wall exposure for promotional items and seasonal products.
After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appropriate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with homeowners and builders to make sure that the work will meet code and will endure.
Use the scrap piece of plywood to map out the angle for the speaker stand legs. Decide the height you want for the base of the speakers, and make a mark on the plywood (32 in. for us). Mark the depth of the speaker (13 in.). Lay the 1x4 board assembly on the plywood, lining it up with both the corner of the plywood and the 13 in. mark from the edge. Scribe along the 1x4 board assembly, take the assembly away, and find your angle with a protractor or speed square (17 degrees for us). Cut that angle onto one end of the 1x4 board assembly.
I would definitely stick with the vapor barrier under the floor to avoid moisture from breaking up the OSB. try to build the base high enough to keep it dry and allow airflow to dry it out under there. FYI I recently repaired a neighbor's shed roof that must have been partially repaired before with plywood. The OSB was fine under the shingles, but the plywood was wrecked due to moisture. I would stick with OSB. Since you live here in NOVA, details will be a little more helpful to you. I really can't use the shed in the summer without the AC on. It gets direct sun and gets up to the 90's in there with out any air movement. I am planning on eventually lining the inside of the ceiling with that thin reflective insulation to bounce back some of the heat.
To help, it’s important to determine the average price per square foot for your area. Price per square foot is typically derived from the annual lease amount divided by the total rentable square feet of the space. You can find the average price for your area by typing your zip code into LoopNet’s directory of commercial properties available for lease.
Thanks to you I built my own truck camper. I bought a LEER top and put a memory foam mattress in the back. I built a basic wood frame, and tried to maximize living space and comfort. It feels more like a Truck Bedroom then Truck Camping. I use bed sheets and blankets instead of sleeping bags. I haven’t seen this as very common. Do you foresee any issues with doing it this way?
One site that I found a year or more ago was Life Remotely. They converted their truck to accomodate 3 people traveling from Seatle to the end of South America. They camped in tents most nights and some hotels/hostels but did a lot of conversions to their truck. Plus they blogged the whole time which is pretty cool if you want to take the road trip international.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wiring for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to finishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a programmable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.