One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strap­ping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
Our Advice: Plan for aisle and display pathways of at least three feet, six inches wide, without obstructions. Then, once your fixtures and displays are in place, further test your store’s pathways by rolling a large baby stroller throughout your store. If you can easily navigate all traffic pathways, your customers should enjoy a comfortable browsing experience.
DeAnna says that in general, the front left of a retail store is a good location for the checkout counter, like the one above. Shoppers naturally drift to the right when they enter a store and tend to loop around the store, leaving on the left side. So, a checkout at the front left of your store puts it your customers’ natural exit path. Plus, it doesn’t distract them from shopping as they make their way around the store.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.

There are some variances in the features and reliability of different model years, and differences between the Mercedes Sprinter, Dodge Sprinter, Ford Transit, and Dodge Promaster - so make sure to do your research. The Sprinter RV Conversion Sourcebook is an incredible resource on all things Sprinter (and van conversions in general), and it goes over all the options in detail.
Expert Tip: Banks are often reluctant to provide long-term small business funding. They prefer short-term loans that are associated with physical assets, which can then serve as collateral. So instead of just asking for a generic loan, maybe consider raising capital for specific equipment that will kickstart your new business, like an espresso machine or delivery vehicle.

Up until about ten years ago, if you were in the process of starting a small business and wanted to use all of the technologies listed at the start of this section, you would have needed to take out a second mortgage to cover the bill. Investing in retail technology has historically involved expensive hardware (including an in-house server), large upfront software costs, and hefty ongoing bills for customer support or repairs when things went wrong. Innovators were targeting large-scale enterprises like Coca-Cola, not local mom and pops, so the packages and price points were designed to match.
Well, my workshop is finally complete and I’m ready to take on just about project that comes down the line. And I’m pretty well set up here. I’ve got a great workbench, plenty of table space over here that easily rolls around the shop if I need it, lot of storage space down here, I can tuck these tools away or bring out any new ones that I need. And as you can see I’ve got plenty of supplies to tackle just about any project.
I don’t own a dog, but I have taken my buddy’s two dogs out with us to the trailhead at least. Not sure that I have great recommendations for how you would go about living in the truck with your dog. All we really did was lower the large wooden deck to the bottom position, throw down some soft doggy beds and pillows, then cover it all with a giant blanket which also covered like the side bins to keep dog hair from getting all over. It was nice and cozy for the dogs while driving down the road. Then we just put packs and other gear on/in the side bins. We used some big metal clamps to secure the blanket to the side bins and keep it from falling down or sliding around. I would think avoiding any carpeting would be a good bet, just go with blankets and things than can be taken out, cleaned, and you can sweep out the back.
Woodworking isn’t just an overnight hobby, for most it’s a fun pursuit that lasts a lifetime. As your skills develop, the workshop becomes a place not just to build but to repair along the way. In a world where people are strongly influenced by consumerism, there’s a tendency to revert to a throwaway culture. But if you can fix before throwing away, then your tools start to make a return on their investment and have a bigger impact.
You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.
But now is the time to take a step back and go on some test runs in your van. Take it out for a weekend here or there (or better yet, a week or more). Try living in it as you expect to on the road. We guarantee there will be things that worked well in your head but not so much in reality. And you’ll come up with random little hacks and innovations that will make your life on the road easier and more enjoyable.
Can you outfit your shop with all the necessary hand tools for just $100? Christopher Schwarz says you can, and he’ll show you how to do it in this article. Take Christopher’s shopping list to the flea market and come back with everything you need for less than you’d spend on one new hand plane. You can do all your woodworking with hand tools, and this article from Popular Woodworking will equip you with everything you need.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
A table saw is one of the most important tools in the workshop for its ability to make long straight cuts. It will also cross cut with ease and if you don’t want to cut clean through a board you can adjust the height of the blade to make a dado or rabbet. A handy feature with the BTS10ST table saw is the vertical stand which also saves on storage space.
For now we’re just getting it out of the room so that our electrician can get started. In any kind of workshop you want plenty of access to power and lots of use of the light. So Mike our electrician is hooking us up. If a service call from an electrician isn’t in your budget you can plan your space so that you can best take advantage of the outlets that are already there. Now Mike has checked all of these surfaces to be sure they can handle these extra outlets he’s adding.
What I have done in my man cave of a shop is to install above my finishing table a strip of track lighting where I have fixtures ranging from the typical bright white incandescent (typically around 4700k) all the way to the average halogen spot that I figure someone would use with an art piece (normally around 3700K). this allows me to point each light and view my piece and finish under varying light conditions to judge whether or not I prefer a particular finish or not. It also helps in photographing items (though filming is a whole nother story, I still have my 5400k T8 overheads for working).
At some point in the process of starting a small business, it’s pretty much guaranteed that you will hear the following statistics (or variations thereof): 25% of new small businesses close their doors within the first year and 60% are gone within three years. The exact numbers here may vary, but the message is all the same: be afraid, be very afraid!

In addition to keeping your workshop comfortable with climate control add-ons, don’t forget to keep your body in optimal condition as you work. A water cooler tucked away in the corner of your workshop will provide a big quality of life boost and allow you to keep at your projects without having to run to the kitchen for a glass of water every time you feel thirsty.
Debt financing involves borrowing capital that must then be paid back over a set period of time, most commonly with interest. Typically the core benefit of this arrangement is that you, the business owner, maintains complete control over your business. Your only ongoing obligation is to repay the loan with interest. The downside? Fail to keep up those repayments and the loan — often secured against your assets, savings or property — can put you in very dangerous financial waters.
Planning your store layout is no small task, but many small retail store owners do it all themselves with great success. So why not you? Take it slow, follow our seven steps, and remember to put the customer first. With the ideas in this guide and a little elbow grease, you’ll soon be on your way to mapping out a retail store that’s easy to navigate, welcoming to customers, and best of all—profitable.

Ordinary clip-in-place shelf brackets with slotted metal supports can hold a lot of weight. But some-times they’re unstable and can be easily knocked loose. The play in the slots allows the bracket and shelf to shift from side to side. To prevent this, use your circular saw to cut 1/8-in. deep slots into the undersides of the shelves, aligned with each bracket. When the shelf is assembled, the brackets fit into the slots, eliminating the sway. Also check out: How To Build Floating Shelves.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.

Ultimate Small Shop is a complete guide to setting up your own workshop, from the planning phase to optimizing it for business. You’ll learn how to put together a complete and functional workshop for less than you expect. Ralph aims to get your shop set up for less than $1,000. Ultimate small Shop includes suggestions on where you can get the tools and equipment needed at the most affordable prices and how to optimize space to get the most out of the little room you have.


You can see in this step how I notched each rafter to fit more securely to the walls.  I also used a metal hurricane strap to secure each rafter to the wall.  Even though this was not required by code, I felt my tools were far to valuable to be left to chance over such an inexpensive solution.  The walls are a simple board and batten system.  The 1x3 trim covers the joints of the 4x8 OSB.  They make much more high quality sheets goods to use as siding.  However, the cheapest I found was $35 a sheet and the OSB was about $5 a sheet.  I sealed the OSB and painted it with exterior paint.  If I run into problems in the future, I can just add a second layer of more durable material or simply have siding installed.  It has held up very well over the past couple years and I see no need to spend more money on it now.

Amenities and Services – You’ll want to understand the full range of amenities offered by a commercial space. These amenities and services may include such things as communal rooms, free Wi-Fi, loading bays and docks, dining options, outdoor space, sewage and utilities, on-site security, and more. The zoning of your business will often dictate the type of amenities and services you require.
For small business owners starting or wanting to grow a small business, attracting and retaining customers is a huge priority. Let’s face it, without customers you don’t have a business to run. Over the last decade there has been an explosion in the number of high-quality, affordable technologies that are specifically geared towards helping small, local business owners improve the day-to-day operations that impact this aspect of their business. This includes point of sale systems, tax software, bookkeeping software, employee scheduling and payroll programs, inventory tracking tools, customer loyalty programs, gift card technology, ecommerce opportunities, website builders, email marketing software, and social media management tools. The list goes on and on.
We first obtained legal permission from Hasbro [which originally developed the Transformer toy line back in the 1980s] to build it late in 2015. I also had to obtain my commercial driver’s license (CDL), so I spent a few months learning how to drive a truck while simultaneously spending the winter of 2015-16 working with Western Star to piece together on paper a vehicle that mirrored the Optimus Prime truck. Once the factory delivered the truck in April 2016, we got to work on the customization and fabrication right away. It was roadworthy again by October 2016. So the entire process from start to finish was about a year.
Once you’ve planned the basic layout of your workshop and have added all the tools and speciality appliances you need, take a last look at the overall design to make it aesthetically pleasing. Add overhead lighting for general illumination and task lighting over your work stations so you can see your project clearly. For maximum flexibility, you can mount clip-on work lights to nearby shelves and point them where you need them, knowing you’ll be able to move them about as required for different projects.
Tired of the rat race, I opted for early retirement. Looking for something to do with all my free time, Ultimate Small Shop Ebook Free I started crafting and am now making a nice supplemental income from it. As a crafter and a businesswoman, I feel I have some valuable insights into the craft business that I can share with you. At some point in your progression from crafting for fun to crafting for fun and profit, you go from handcrafting individual items for yourself and friends to filling quantity orders for a broader marketplace. That’s the time to take a very business-like approach to your craft business. This needn’t be daunting. You don’t need an MBA or management experience – just a bit of common sense. If you’re going to do this for profit, you need to understand Simple, right? But very few people get it. Look at the high failure rate for new businesses. It takes an effort to be successful, but the task is hardly impossible. Traditional craft retailing methods are what most crafters use to get started. They’re the easiest way, especially if you don’t know if anyone will buy what you make. I believe that there is a market for any well-made craft, whether decorative or useful. The problem facing many crafters is how exactly to go about selling them, or more accurately, finding paying customers. The fact is that there is an awful lot of competition out there. My own business got jump-started by my “circle of friends”. Ultimate Small Shop Free My friends noticed and liked my calling cards and began to ask me to design and make cards for them. Starting with just Broderbund’s Create-a-Card program, I was soon earning a nice supplemental income in just a few hours a week. It probably helped that I was retired and live in an area dominated by retirees. But I think that everyone has a “circle of friends” either socially or at work. Of course, you don’t want to impose on their friendship by making a hard sell, but rather use or display your crafts in front of your friends to see if they draw any interest. If they do and if they’re priced right, you’re on your way to craft retailing for profit. If your “circle of friends” market starts extending to friends of friends, you’re probably ready to tap the general marketplace of craft retailing. Most crafters are aware of the periodic craft shows put on by local groups or even by the local Parks Departments. These usually cost little or nothing to join and should give you a fair idea of whether there is any broader interest in your craft. What better way to jump into craft retailing? There are also organized craft shows that tour the country, Ultimate Small Shop Legit most of which charge an entrance fee for participants.
Plan to invest in a set of bench chisels, both standard and low-angle block planes, a No. 4 or 4-1⁄2 smoothing plane, and a No. 6 jack or No. 7 jointer. Between them, these planes will true edges, flatten glue-ups that are wider than your thickness planer, and tame tricky grain that would tear out with a mechanized planer. They also do fine trimming better than any other tools.

This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.
Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on.  The rewards aren't usually good enough to compel me to purchase on their own.  But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.
7. Illuminate your space in different ways. Lighting is important in any retail shop, but it's particularly critical in tight quarters. If a corner of your store is not well lit, that square footage is as good as lost, Langdon says. She recommends using a combination of track lights, lamps, sconces and picture lights. This mixture will not only ensure that your entire space is well lit, but it also will add flair and variety. "Picture lights are amazing. They give a wonderful glow," she says. "Think in terms of layers of light."
3. Think vertically. Displaying items on various levels maximizes space and is visually appealing to customers, says Jerry Birnbach, a Somers, N.Y., store-planning consultant. Hanging shelving at different levels is the easiest way to achieve this effect. You also can mount drapes and other items from the ceiling to the floor to draw the eye up and create the sense of a larger space, Langdon says.
We have Eclipse Sunshades installed on our van. While they’re pricier than the cheap sunshades you’ll find at Walmart, they’re every effective. And since they permanently install on your windshield they’re much more compact - a big plus for living in a van. All we have to do is pull the shades across and velcro them together in the middle and we’re protected from both the sun’s rays and prying eyes.

1. Paint an accent wall. Painting one wall a bold color is an affordable and effective way to not only spice up the space, but also to make it look larger. A bold colored wall creates the illusion of receding in space, says Libby Langdon, HGTV design expert and author of Libby Langdon's Small Space Solutions (Knack, 2009). Putting colorfully printed fabric or wallpaper on one of your walls is another way to achieve the same effect, while adding eye-catching textures and patterns to your store.
Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.
YouTube: I love this place! You can find video training's on just about everything! It can  help you with a lot of the tasks that you need to accomplish for your goal. So if you want to "sell products using Instagram" and one of the tasks is: post beautiful photos with text on my feed often, then you probably need to go on YouTube and search for "how to design an Instagram post, if you don't know the first thing about it. You can use YouTube to help you accomplish goals or tasks on your list that is out of your skill set. 
I didn’t want to get a truck with a million miles on it. I am not a trucker by trade; I got my CDL specifically for this project. I didn’t want to get into a truck and then have to worry about its structure, engine, and transmission—and then start building Optimus on top of it. That’s why I got a brand-new truck custom-built from Western Star to become Optimus Prime.
For many new small business owners, the additional expense and bureaucratic hoopla involved in obtaining the correct paperwork often leaves them dragging their heels. This attitude, however, can result in stiff financial penalties, or worse, having your permission to do business revoked. Before we jump into the why and how of obtaining your business permit or license, it’s important for you to understand the difference.
We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).
Tight control of inventory, while not a particularly glamorous part of owning a small business, is therefore one of the most important ways you can impact profitability. The good news now is that there is an array of technology available that can make this whole process much smoother, including sophisticated forecasting tools that will help you predict your required inventory levels for each day based on past sales, weather records, and many other factors.
A lot has changed in recent years. Sophisticated, yet affordable technology now exists that can help track customer relationships from an ad placed on Google, right through to a successful sale. This offers small business owners a unique chance to be entirely data-driven in their marketing approach. Every single aspect of your small business can be tweaked and optimized to ensure that you are enticing customers, up selling where possible, and encouraging people to spread the word about your business.

One practical note: Lots of retailers and restaurateurs are now engaging in event marketing in their business locations. Lululemon does in-store yoga on Sunday mornings, Barnes and Noble hosts author readings, and your local Italian restaurant may offer cooking classes. Think about all the potential use cases for your store and ensure that it is fit for purpose.


In our Complete Coffee Shop Startups Kit, we spend a good amount of time discussing your health department requisites, your coffee equipment, and even the design of your coffee shop. Since this makes up a significant bulk of your startup costs (equipment, space requirements, etc.), we recommend that you spend an extra couple of hours strengthening your knowledge base with listening to our audio interviews.
Congratulations !! I think 62 days is quick ! thats a big project. Now that its done and you got to get everything else set up it kinda sucks that you will also need to start making the payments, yuck. However I think it will be a good investment as your show continues to grow . I certainly love it ! I look forward to what you have in store. Thanks
Back in the 1970s and treeplanting in Oregon, I and Tony Lessa lived for two weeks at a time in the back of my 1954 Chevy PU. The canopy was just a simple shell with the board across next to the cab. After the fourth or fifth trip out in the season the accumulated funk was too much. You can imagine two hard-working guys in very muddy and cold conditions coming in after work with dirty wet gear. Pretty desperate circumstances but before Reagan trashed the treeplanting industry our coop ( Hoedads & then Second Growth) was making good money so we endured the hardships. It works for the young. Now, at 76, I find sleeping two of us between the wheel wells in a Dodge G. Caravan (seats removed) much too crowded. I think I will tent and the wife can have the van.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
Before you bid in an online auction, check the site’s rules of operation. At some sites, a winning bid is a binding contract, which can be a problem if you can’t inspect the tool before you purchase it. Don’t forget shipping costs. In some cases they can exceed the cost of the tool. Also, make sure the tool you’re buying will run on the power you have in your shop. Many former industrial tools run on 240v single-phase power. If your shop doesn’t have 240v service, you’ll need to factor in the cost of upgrading before deciding to buy. You don’t want to saddle yourself with a tool you can’t use, no matter how good the price.
In our opinion, the best kind of fridge you can get for a DIY campervan is a portable 12V fridge/freezer. These fridges are built for adventuring on 4x4 vehicles and boats. They’re very rugged, and they don’t need to be kept perfectly level like mini-fridges. They can run off 12V power or regular 110V. They keep your food as cold as you want, and they can operate as either a fridge or a freezer.
I have a question, you mention what a problem it would be if the cinder blocks were to sink yet you have installed them with the least amount of footprint on the ground. Was there a reason for this? I would have installed them with the flat side on the ground, and I realize they would not hold as much load as the way you have them but considering the number you have used, the spacing, and the size of the shed, load should not be a problem. Just wondering.

You may already be aware of something known as the "butt-brush effect," coined by consumer behavior expert Paco Underhill. He discovered that a typical customer, especially women, will avoid going after merchandise in an aisle where they could potentially brush another customer's backside or have their backside brushed. This holds true even if the customer is very interested in a given product. An easy way to avoid this problem is to ensure that your aisle, floor, and displays allow customers to have more than adequate personal space when browsing your products.
If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
One example is testing your products and services for their desirability through ecommerce. It might turn out that your core product line will actually be much smaller than you originally envisioned. Equally, there are now a number of services (such as storefront.com) that will allow you to secure a pop-up lease in some incredible spaces, often for only days at a time. It might just turn out that your dream location isn’t as great as you originally thought.

This OXO palm brush really helps us conserve water while washing our dishes. We fill the reservoir with water and a few drops of Campsuds, and we only squeeze out what we need - so it takes care of both the initial rinse and getting our dishes soapy with minimal water usage. It’s also very compact, and the comfortable shape makes it easy to scrub dishes.
Power outlets are also needed for lighting, heaters, AC units, radios, televisions, CNC machines, 3D printers, and computers—all of which you’ll find in many workshops (although maybe not together, and maybe not all in your garage.) You simply can never have too many outlets and it’s much safer to have too many than not enough. Bring in an electrician to help install your outlets and setup 220v power if needed for larger shop tools.
Tired of holding a flashlight between your teeth while working in the dark? Make a light stand by bending a 2-ft. section of 12- or 14-gauge electrical cable into a U shape. Duct-tape the light to the ends of the cable. The wire can be shaped into a hands-free supporting base for the flashlight or bent into a hook for hanging. — Paul and Haylee Lytle. Check out another hands-free light hack.
While a single great product can’t usually support a whole business, it is beneficial to select one or two “headline” products that will form the cornerstone of your offering. This will often be an obvious choice: If you’re a coffee shop, your headline product will be coffee. If you’re a burger joint, you guessed it, it’ll be burgers. This product will often be the centerpiece of your marketing efforts and a way for you to “own” a space in a customer’s mind. For example, Jack’s Burgers makes the best cheeseburger in town and Daisy’s Threads has the most adorable scarves.
This is where I started thinking about how I was going to store all of my lumber.  I had planned on building a wall rack, similar to what I had used in my single car garage.  But I hated using up an entire wall for lumber storage.  I also knew from experience that I would easily lay stuff against it and soon be digging lumber and junk out of my way.  I decided to use the space under my workbench to store the long boards and I realized that by pulling my bench out from the wall I could slide sheet goods behind it.  This created a problem:  How do I get it out.  The Shop isn't long enough to pull out 8 foot boards from inside and I would probably have to move things around to get to it anyway.  So my plan for this came at kind of a sudden epiphany moment, when I decided to cut access doors in the front and build my storage into my workbench area.  This has been the single best idea that has come out of my shop.  I can't express enough how easy it is for me to get straight to a board i need with no hassles.  I just remove the doors and pull out what I need.  I can store a surprising amount of lumber in this area.  I do have a secondary area for some cutoff sheet goods and a scrap bin next to my table saw in the garage.  But this area stores most of my lumber.
There you have it! Now you have no excuses, you must start planning right away. Please remember this can take a lot of time and a lot of work, so be sure not to stare at your task list in its entirety too often. I don’t want you to get overwhelmed knowing all the things you must get accomplished. Just focus on the goal that is the most important and attack it, task by task. Need help organizing these goals? Check out my Goal Planning Worksheets here:
If you want the ability to cook inside your van but don’t have a whole lot to spend, your best option is the Coleman Classic propane camping stove. For about $60 you get a sturdy and reliable 2-burner stove that runs off of replaceable 1-lb propane canisters. We’ve seen many people using these out on the road, and they do the job very well. Coleman has hardly changed the design of these stoves for decades, so you know they’re doing something right.
This is about how I built my wood shop. We decided to move from our previous home for a variety of reasons. I saw the move as an opportunity to gain a bigger shop for my wood working hobby. The house we found had everything we wanted, except for a shop or even a garage. It did have a non functioning indoor pool. We thought this space would make a nice wood shop. I could just build a floor over the pool and have a shop. As we got further into the inspection process, it was looking as though fixing the structure over the pool was going to be expensive. It looked like we would have to put a bunch of money into a structure that was not really a wood shop and not a functioning pool either. It made more sense to take out the pool and structure, and then build a wood shop from the ground up. We started this project by regrading our side yard to gain access to the pool in the backyard. Once we had access, we took out the pool. We half filled the hole where the pool was with compacted gravel. I realized that if we sank the shop into the ground I could have the ceiling height I had always wanted in the shop and preserve the view from the house. The design of the shop is a box with a shed roof. The roof wraps down the east side of the structure. I like to think of it as a slightly open toolbox. The entire shop is laid out on a 24 inch grid. The windows and doors fall within this grid. I had a general contractor built the shell and then I built the windows and interior. The interior walls are comprised of a 34 inch concrete stem wall at the base. Above that is a 9 foot, plywood wall. In the space above the plywood wall and below the shed roof is poly carbonate panel to form a clerestory. The tool layout in the shop is divided into 4 areas: an area near the door for material storage and prep, a central area for general wood working, and two areas near the back of the shop, one for turning and one for metal working.
They’re also very energy-efficient, so they won’t be a heavy load on your batteries. The best 12V fridges use highly-efficient compressors that have very low power draw (0.7 - 3.0 Amps per hour, depending on the model and the ambient temperature). They’re also well-insulated and feature top-open lids, which prevent the cold air at the bottom of the fridge from escaping when the lid is open.
If you’ve been to gem shows, you know how overwhelming and daunting they can be. Although it’s difficult to narrow down all those tempting options, your jewelry business profit margin will be greater if you plan ahead and focus on shopping for a particular line and color scheme of jewelry. Ultimate Small Shop Online Review You must keep the bigger picture in mind and try to keep your emotions out of the design process. Here are some tips for defining your market and researching it so that you can walk in and out of a gemstone show feeling confident in the business investments you’ve just made. Gemstone shows and fairs are marketplaces for vendors of gemstones, findings, jewelry supplies, and tools. Due to a large amount of competition between the vendors, prices tend to be competitive. I’ve found unbelievable deals on high-quality gemstones and findings at gem shows. To find gem shows near you, you can simply do a Google search for “gemstone show” or “gem fair”. Other sources of information are your local convention and visitors’ bureau and any lapidary clubs in your area. Anyone can attend most gemstone shows. Although you don’t usually need a wholesale license to get in, some vendors may ask for your resale permit before letting you buy at wholesale prices. Show admission fees tend to be in the $5 to $10 dollar range. What market are you trying to target with your jewelry? Don’t try to please everyone. Ultimate Small Shop does it really work Are you trying to appeal to individuals like yourself? What age bracket are you trying to reach? Does your jewelry line appeal to funky or traditional individuals? Next, take a trip to your local department store and take note of the colors that are being used for the upcoming season. Look at the jewelry and observe the lengths of the earrings/necklaces, the sizes of the stones, and the other various style elements for the season. While your designs should not be copies or replicas of the jewelry in the stores, you can simply incorporate the observations you make into your own original design ideas. Fashion and jewelry magazines are also a great place to find out what trends are coming into the stores. There will be an overwhelming array of gemstones and supplies at the show. Having a jewelry line style and color scheme in mind will allow you to narrow your focus. Vendors will offer gemstones in more shapes, sizes, cuts, and colors than you can imagine. Stick to the colors you’ve mapped out for yourself and walk through the entire gem show once before buying anything. Jot down and compare the prices of items that you’re interested in. Then take a break, go outside for some fresh air, and reflect on the items you saw and really liked. Then review your budget and the jewelry line you have in mind before returning into the gemstone show. Ultimate Small Shop Guide Download This will help you get the best deals on the items you’re most interested in so that you don’t blow your budget or become overwhelmed by the options. Soaring through the air, watching the clouds and the birds fly by.
Unfortunately, the requirements across the country and across different industries are as varied as the bodies enforcing them. The only way to guarantee that your licenses and permits are all squared away is to seek out regulating authorities on the county, state, and federal level, as well as consult with the relevant industry-specific bodies for your business type.
Once you have your space secured, hang some pictures in the windows that illustrate what’s to come. It’s also a good idea to provide leaflets that people can take away with them and hang a clipboard and pen on the front door where people can sign up to hear more about your business. This list is pure gold! So once you have it, why not stage a launch party and invite the local community (and local journalists). The first step for any business is always getting people to try out your products!
Through my cabinet-shop connections, I managed a snappy deal ($200) on a used cabinet saw with a 54-in. commercial rip fence. That price would be hard to match, but it is possible to find a hybrid or used cabinet saw with a high-quality fence for $600 to $1,200. Some of them will run on 120v household current, meaning you won’t have to rewire your shop for 240v service, but be sure to check for compatibility before you buy.
×