A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
If you have a broker that’s too successful you may be a low priority. If you choose a broker that’s inexperienced but attentive, you may end up paying for their novice mistakes. My advice is to not choose a broker but instead choose a team. Pick a junior/senior combo so that when you’re hunting for space you work more with the junior, and when it comes to negotiating the deal you have the experienced veteran leading the negotiation.”
As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
In all you can spend under $1,000 and be setup in a great workshop. But I know how it feels when you’re shopping for new tools… and you think… “why not buy the top of the line so it lasts longer”… or “may as well get the best while I’m spending money”… those kinds of thoughts won’t only get you into big trouble with your other half… it’s also COMPLETELY wrong.

Now I want you to create a spreadsheet or use my worksheets and write one major goal on the top. This can be the first goal you want to accomplish. Then I want you to list all the tasks you need to do (or someone on your team has to do) in order to accomplish this task. For example; let’s go going back to the goal of "Launching a New Website". The tasks you will need to do to get this goal accomplished are the following;
The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself).
In all you can spend under $1,000 and be setup in a great workshop. But I know how it feels when you’re shopping for new tools… and you think… “why not buy the top of the line so it lasts longer”… or “may as well get the best while I’m spending money”… those kinds of thoughts won’t only get you into big trouble with your other half… it’s also COMPLETELY wrong.
Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.
Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
Also, heard of anyone camping in an Accord sedan? I’m wondering if it’d be worth it to buy a new Tacoma to convert into a dirtbaggin’ vehicle or if I should try to make it in a sedan. Lots of variables… I’ve got the cash but it’d eat into the “cushion” I have for living on the road (about 50% of it). OTOH I could buy a used Tacoma, but they hold value so well it’d seem like long term it’d be best to get it new. I’ve seen some with 250 miles sell for $8,000+. Thoughts on getting a new truck using my beat-up sedan?
Tired of having your caulk tubes lying all over the workbench or your shelves? Make this organizer from a scrap of 2×8 and a piece of 1/4-in. plywood. Just lay out a pattern for your 2-in. hole saw to follow and drill holes through the 2×8. Then glue the plywood to the bottom. Now you can set it on a shelf and easily identify the tube you’re looking for. — Burnie Lorenz
Finding reliable cellular service (and the internet that comes with it) is a constant challenge in vanlife, especially if you do computer-based work on the road. A cell signal booster like the WeBoost Drive 4G-X helps a lot in areas where service is spotty. It can take a weak cellular signal and amplify it into usable internet for web browsing and getting work done.
Hi thanks for the info. I’ve got a 2009 tacoma and went with a simple, no screws elevated system. I’ve also got a mx series ARE shell with rack rails so I’ll probably take too much stuff now. Oh well. My question is: how did you attach the plywood to the life gate? My carpentry/construction skills are best illustrated by the “Homer Simpson spice rack”. You used the existing holes in the tail gate, but did you put the tail gate cover back on the tail gate and put the plywood over it and screw thru both or ditch the cover? Thanks

I have a basement shop with a walk out and a seperate entrace to my shop.I have approx. 5oo sq feet to work in there, there is natural light that comes in with a graet view of the lake that we live on.I have started to dress up my shop after making such beautiful furnisher for other people it started with a bench witch is 11 ft, long and plenty of stoarage space under the bench , the low storage aera of the bench is made from black walnut and the bench top is oak with bubinga trim. Saw cabient is white oak ,miter saw cabient is walnut ,american chestnut ,cherry and maple. Now the joint cabient looks out of place so I will be making a better looking cabient for the 6in. jointer. I had made a plant self to start plants along the widows but took it out and put a bench top there so it looks as a big window sill but I use it for a place to set tools as I am working on the bench also I have put walnut around the widows and painted the walls.There is a 10in. powermatic table saw,powermatic drill press fl.modle,rockler 6in. jionter, mekeita compond saw,delta 14in band saw, I have two planers and a table mount router in my bench top ,also there is an old american lath witch I have in stoage and a sears jig saw.
Ultimate Small Shop is a turnkey solution for woodworkers to get started with their dream workshop. Every woodworker, hobbyist or professional, wants a nice workshop in their home. It may be the garage or a shed, the barn or a detached man cave, the basement or a room up somewhere with enough space. Woodworkers often fail to create their dream workshops due to dearth of space and funds. Ultimate Small Shop solves both these issues and empowers woodworkers to live their dreams.
If you want that homey cabin feel inside your van, then lining the walls and/or ceiling with tongue-and-groove paneling is a good choice. Paneling looks awesome - the cedar paneling on our ceiling is one of the defining features of our van. And we cut ours to random lengths and stained it several colors to really give it that mismatched, rustic look.
I have a question, you mention what a problem it would be if the cinder blocks were to sink yet you have installed them with the least amount of footprint on the ground. Was there a reason for this? I would have installed them with the flat side on the ground, and I realize they would not hold as much load as the way you have them but considering the number you have used, the spacing, and the size of the shed, load should not be a problem. Just wondering.

Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
State Parks/Developed Campgrounds. Every once in awhile, it’s kind of nice to stay at a state park or other developed campground - and a big reason why is that they have showers (and sometimes laundry, too). This is what we’ve done most often when we need a shower on the road. Many state parks also have small day use fees if you don’t want to actually camp there.
Tired of holding a flashlight between your teeth while working in the dark? Make a light stand by bending a 2-ft. section of 12- or 14-gauge electrical cable into a U shape. Duct-tape the light to the ends of the cable. The wire can be shaped into a hands-free supporting base for the flashlight or bent into a hook for hanging. — Paul and Haylee Lytle. Check out another hands-free light hack.
One thing I found while looking on the topper websites is a piece of weather strip designed to go between the tailgate and the truck bed. It has a special wedge shape to it so when you close the tailgate it makes a watertight seal. It is just the thing to keep the dust and dirt from entering the back of your rig when driving down the dirt roads. They’re inexpensive too, for a full size truck like my Dodge it’s only $25. It has adhesive on one side, so installation looks simple.
Hey thanks for the great insight on a pickup camping setup! I just purchased a 2002 tundra with a 74″ bed. Picking it up in Denver in a week and driving it to Durango and then around the southwest. I mainly decided on a truck for a mobile place to keep my dog(that doesn’t have an interior he can rip to shreds), but I am thinking of building a setup similar to yours. You haven’t used yours with a canine companion have you? Any suggestions on keeping it dog-friendly, dog-comfortable and dog-proof? I will be keeping him in the back while at work and such and will be camping in the back with him and possibly another person.

A battery isolator allows your vehicle’s alternator to charge your auxiliary batteries while you drive, and keeps everything separated so you don’t drain your starting battery. Since we installed our Keyline Chargers Dual Battery Smart Isolator, our batteries are almost always fully charged. It’s also very simple to install - the toughest part is running the cable inside your van from the engine compartment.
as the name implies--I have no qualms about using castoffs, trash or clearanced items in my shop--I have a 3and one half car garage that I can't get a vehicle in(even tho I like to change my own oil, etc.) because I have so many interests like woodworking, metalworking, plastics, machining, machine building, carpentry, etc. we have to store our kids furniture somewhere, as well as some of our own... You involve a welder, 2 tablesaws, bandsaw, planer, lathe, drillpress, benches and benchtop tools--not to mention storage of materials and I've got a collosal mess that I may never get straightened out!!!--Did I mention room for the woodburning stove I heat it with??? I am always appreciative of these "dream shops" I see in FineWoodworking"
Just as a shed or garage can get stifling in the summer heat, winter cold can also make working conditions difficult — if not impossible. To prevent clumsy, stuff fingers from ruining your projects, you need a way to heat your workshop in even the most extremely frigid days of the year. A traditional residential space heater probably won’t cut it, as these are designed to heat single rooms. For a two-car garage or full basement, you’ll need something much bigger.
Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.
Using six pipe cleaners, you can make your own skeleton. Bend one pipe cleaner into two for the backbone. Twist another around the bottom of the backbone to make into the legs. Do the same for the arms. Join two pipe cleaners and twist them around the backbone leaving some space forming a ribcage. Ultimate Small Shop Woodworking Twist the last pipe cleaner for a head and glue on some eyes. Hang with a rubber band for a bouncing effect. Your kids will love making Halloween crafts with pipe cleaners. But be careful when cutting and keep them out of their mouth. Going trick or treating? Why not make a special jug to collect candies? Cut off the top two inches of a gallon milk jug. Soak to remove any labels. Paint orange. Once dry, paint or stick on eyes nose and mouth resembling a Jack O’Lantern. Use fluorescent paint for a nice effect. The jug can be kept for future reuse. Using glue and food coloring, you can make a see-through painting. Paint a Halloween image onto a piece of plastic wrap. Before the mixture dries, put another piece of plastic wrap on. Cut it out and hang it in front of a light source for a see-through effect. You could also frame the plastic pictures using wood or cardboard if you want them to be longer lasting. Make some hand printed spiders. Ralph Chapman Ultimate Small Shop Apply black paint to your palm and 4 fingers leaving out the thumb. Place palm onto a piece of paper. Turn the paper 180 degrees and print again making sure the palm overlaps. Add some wiggly eyes using either paint or sticks. This is suitable for even 2 or 3-year-olds. Make your own blood. It is less expensive than buying ready-made blood from the Halloween shops. It’s not difficult; all you need is Karo syrup and food coloring. While you’re at it, why not make some slime using glue, water, and borax powder. This is an advanced Halloween craft, so take your time and be careful. Using apples, you can make dried, shrunken heads. Peel the apples and coat with a mixture of lemon juice and salt to prevent browning. Carve out a face of eyes, nose, and mouth. Do not worry about the finer details as they will probably be lost when the apple dries. You can use whole cloves for the eyes and rice grains for the teeth. Let the apples sit out in a warm place for about 2 weeks. If you don’t have 2 weeks, you can speed up the drying by putting them into an oven on the lowest temperature for about 45 minutes and then dry out naturally for the next 2 days or so. Ultimate Small Garage Clock Shop Once dried, they shrink and deform into weird and scary looking faces. Says Angie Maroevich, “You don’t have to spend a fortune on commercial Halloween supplies to have a great party.
In addition, if your aisles aren’t wide enough, you could be subject to complaints or lawsuits under the Americans with Disabilities Act (ADA). The ADA requires you to have aisles that are at minimum three feet wide. If you’re reported to be non-compliant, you could be fined if you don’t widen your aisles and remove obstructions. Learn more about the ADA’s retail store requirements here.
Hey, I hope we’ve been able to share with you some ideas that you can use if you’re thinking about building a workshop or any type of hobby room or just about any room in your house that you can get this kind of enjoyment out of. We have a lot more details on this shop as well as other things you need to consider if you’re building a shop on our website at todayshomeowner.com. hey thanks for being with us.
Ok Rob let me try again .I would suggest you sign up for a community collage woodworking class or a woodworking coop where you can use the tools you will need to build the kind of items you have in mind. You say you have used the tools you listed but that could mean only used them once or twice. If you have minimal experience with tools and woodworking that might be another reason to take a class assuming there is one available . Do you have a space you can use as a shop ,a garage,carport etc? As far as tools and equipment are concerned I think Knotscott covered it very well. I know your supposed’s said you couldn’t find tools on Craigslist or garage sales but those might be the place you can make an offer on a shop full of tools in the price range you trying to stay in possibly with some materials and other extras. It might even work to put a wanted wood shop full of tools in the tools section of your local Craigslist.
Can you outfit your shop with all the necessary hand tools for just $100? Christopher Schwarz says you can, and he’ll show you how to do it in this article. Take Christopher’s shopping list to the flea market and come back with everything you need for less than you’d spend on one new hand plane. You can do all your woodworking with hand tools, and this article from Popular Woodworking will equip you with everything you need.
To make the most of your workshop oasis, look for a water dispenser that offers a choice between chilled and hot water. This will let you enjoy a cold, refreshing drink in the heat of summer rather than a lukewarm bottle that’s been sitting around gathering dust. You’ll also cut down on the amount of plastic your household goes through, which is a boon for the environment. In the winter, the hot water tap will also you to make a cup of tea or a mug of instant coffee on the spot. No matter what your taste, a versatile drink dispenser will keep you hydrated and happy while you work.

We use this fan for extra circulation when it’s hot, and to get the air moving when it’s cold at night and we have all the windows closed. We also keep it on for our dogs while we’re driving. There are cheaper 12V fans out there, but generally the cheaper the fan the more power it draws. The Endless Breeze is a great little fan, and it’s definitely worth getting for the added ventilation.
Back in the 1970s and treeplanting in Oregon, I and Tony Lessa lived for two weeks at a time in the back of my 1954 Chevy PU. The canopy was just a simple shell with the board across next to the cab. After the fourth or fifth trip out in the season the accumulated funk was too much. You can imagine two hard-working guys in very muddy and cold conditions coming in after work with dirty wet gear. Pretty desperate circumstances but before Reagan trashed the treeplanting industry our coop ( Hoedads & then Second Growth) was making good money so we endured the hardships. It works for the young. Now, at 76, I find sleeping two of us between the wheel wells in a Dodge G. Caravan (seats removed) much too crowded. I think I will tent and the wife can have the van.

There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.


One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
One of the most important and often overlooked first steps when starting a small business is preparing a business plan. Many entrepreneurs who hear this might panic. And while the value of writing a business plan is often debated, those who complete them are nearly twice as likely to successfully grow their businesses or obtain capital compared to those who don’t. More on this in part three of How to Start a Small Business 101, Components of a Business Plan.
Some people lean towards starting a small business because they seek freedom, others to fulfill their passions. Some entrepreneurs, however, are driven by a desire to build a legacy, one that that they can hand down to generations to come. Whatever your reasons are for reaching for the stars and aiming for the moon, before you start, remember, there is a dark side.

If you’ve got 220v, and want to get a seriously good TS, the Grizzly G1023RL is about the best bang for the buck in a 3hp industrial style cabinet saw…$1195/$1294 shipped. It’s not a necessity to have that much saw, but it’s close in price to many lesser saws, and is about all you’d ever need. If that’s more than you can stomach, and/or don’t have 220v, you’re limited to a TS that’ll run on a standard residential 110v outlet….again I’d look to a full size stationary saw. The typical contenders are the entry level price ranges are the Ridgid R4512, nearly identical Craftsman 21833, Steel City 35990, Porter Cable PCB270TS….all under $600. The next step up would include the Grizzly G0661, G0715P, Craftsman 22116 (by Steel City/Orion), Jet Proshop, General International, Rikon 10-201, and Powermatic offerings. These saws all have the potential to perform well…the end performance is largely dependent on how well you set them up, and what blade you choose.

The first thing to understand about a business plan and financial projections is that the process of compiling them is often more important than the final product. Sure, the actual sheets of paper, filled with spreadsheets and graphs with pretty arrows pointing up and to the right are great — and can be very important in helping you to secure funding — however, when it comes down to the brass tacks of starting a successful business, it’s the process, not the paper, that counts.

We think you’re going to find our newsletter and blogs useful and entertaining to read. Because we’re all woodworkers here at Popular Woodworking, we generate a huge amount of valuable woodworking information that we cannot possibly cram into the printed magazine. So the newsletter and community are both great places for us to share what we know with you.
When it does come time to choose a long-term space and negotiate a deal, it’s important to remember that there is more to discuss than just the monthly rental rate. Subjects you’ll want to raise include the proposed length of your lease and options for renewal, responsibility for ongoing maintenance and repairs, payment of utilities, and obligations around property insurance. Parking rights are also essential for many, especially businesses located in a small shopping center.
For the large square windows near the tailgate I just used those big “magic auto shades” like these, which fit perfectly to cover up those side windows and the back window by the tailgate (I had four in the canopy) and another set up in the cab for my actual window. As for the longer side windows I just used a USPS box, haphazardly stuck up against the window. Nothing fancy.
As a carpenter, I need to bring certain items with me every day. I bought a cheap plastic tote in the tool storage area at a home center and modified it for my needs. I made a small plywood deck, drilled a couple of 3-in. holes for coffee cups or glue bottles and then fastened it to the tote. Another piece of plywood has holes to keep pencils upright and organized. My tote sits nicely on my bench seat, but it could also be attached to the floor with hook-and-loop fasteners. You could easily customize these totes for plumbing, garden or painting tools, electrical supplies—what have you. — Don Simms. Check out this jumbo tote for fasteners.

Skoolies do have significant drawbacks, however. Their size makes them a bit unwieldy to drive, and getting to some of the more out-of-the-way camping spots just won’t be an option. If something goes wrong mechanically, it can be much more expensive to fix than a normal vehicle. Also, the sheer size of these vehicles means the gas mileage is much worse than other options.

The first thing to understand about a business plan and financial projections is that the process of compiling them is often more important than the final product. Sure, the actual sheets of paper, filled with spreadsheets and graphs with pretty arrows pointing up and to the right are great — and can be very important in helping you to secure funding — however, when it comes down to the brass tacks of starting a successful business, it’s the process, not the paper, that counts.


It’s hard to overstate the importance of choosing the right location when starting your small business. We’re sure you’ve heard the saying 1,000 times before, Location, Location, Location! Some of the world’s most well-financed franchises have this weaved into their business DNA. McDonald’s Ray Kroc is the perfect example. When asked about the business, this well-know American businessman and philanthropist once stated, “We are in the real estate business, not the hamburger business.”

A business license gives you permission to run a business within a particular territory. It is important to note that not all local governments require you to obtain business licenses, while others only require them for specific business types such as bars or restaurants. To determine whether or not your state or business type requires you to obtain a license visit SBA.gov for state-specific license and permit information.
Shop looks great Marc, I see the Clear Vue in the picture. I love mine, I used 8″ PVC for the main trunk line and came out of that with 6″ drops. It works great. I wound up building a collection bin instead of using a can, only thing I didn’t do was make the bin big enough. It holds more than the typical can but I still should have made it with more capacity. The 1800 with the 5 hp motor is stout.
YouTube: I love this place! You can find video training's on just about everything! It can  help you with a lot of the tasks that you need to accomplish for your goal. So if you want to "sell products using Instagram" and one of the tasks is: post beautiful photos with text on my feed often, then you probably need to go on YouTube and search for "how to design an Instagram post, if you don't know the first thing about it. You can use YouTube to help you accomplish goals or tasks on your list that is out of your skill set. 
Conduction is heat transferred across solid surfaces- think touching a hot stove. It’s also how heat gets out of your van in the winter. The heat inside your van is conducted through the solid surface of your walls and ceiling. Insulating the inside of your van will help prevent heat loss through conduction during the winter, and will also stop your van from conducting the sun’s heat inside during the summer.
A table saw is one of the most important tools in the workshop for its ability to make long straight cuts. It will also cross cut with ease and if you don’t want to cut clean through a board you can adjust the height of the blade to make a dado or rabbet. A handy feature with the BTS10ST table saw is the vertical stand which also saves on storage space.
×