Now also we have some shelves that we built here above this, little cubicles like this work great to organize your workshop so you can have different tools or different supplies in the different little areas. And we’re about to install a very simple countertop. Now this is nothing more than just three-quarter-inch plywood and we decided to stain it instead of painting it, because you know it’s going to take a lot of abuse with all the pounding and the dings, and dents you’ll get in a workbench so staining it and then sealing it with a coat of sealer will probably hold up better than anything else. Now we’ll put another coat of sealer on it after we finish the front edge band and the backsplash and once all of that is complete, boy this thing is going to work nice.
Of all the LED lighting options, puck lights are the most difficult to install. You’ll have to run wiring behind the ceiling/walls for each light. And you’ll need to cut a hole with a hole saw to recess the lights into the ceiling. But with some preparation and care it's not too difficult. We have full instructions for installing LED puck lights in our epic electrical post.
First, decide on wax you would like to start with, there are three different kinds to choose from Ultimate Small Shop paraffin wax, soy wax, and beeswax. Paraffin wax is most commonly used in candles, this wax is found at most candle making stores. Soy wax is all natural, made from soybeans, and cleans up easily with soap and water. Beeswax is all natural too, and making beeswax candles is often easiest because you simply wrap a sheet of beeswax tightly around a wick then seal it with your thumb, which means no melting is required. To begin, spread newspapers around the candle making area. First, you melt your paraffin or soy wax and it must be double-boiled. Usually, you place a large pot that is about half-filled with water on a burner over low-medium heat, place a melter in the water, then gradually place wax pieces into the melter. When the wax has melted, you can add coloring or fragrance as desired. To make molded candles, cut the wick two inches taller than you want the candle to be, then thread it through the hole at the bottom of the mold, then plug the outside of the hole with putty. Place a pencil or similar item over the top of the mold and tie the top of the wick to it, centering the wick. If the mold is cardboard, plastic, or glass, heat the wax to 130 degrees Fahrenheit. If the mold is metal, then heat the wax to 190 degrees. You can use a candle or candy thermometer to measure this. Ultimate Small Shop Pdf When the right temperature is reached, lift the melter by the handle and slowly pour the wax into the mold. Let cool for twelve hours then refrigerate for twelve more hours, then your candle is ready to be removed. To make votives and other small container candles, you can use pre-tabbed wicks by simply placing them in the center of the votive candle molds or containers, then pour the wax mixture over and let stand for twelve hours, refrigerating the votives. By the time your teen is in high school, you probably aren’t taking as many pictures of them as you used to. I have to keep reminding myself that I only have a couple of years left and no time to waste trying to capture fleeing teenage memories. You might be thinking that I’m really organized to be already working on scrapbooking my daughter’s high school memories. To be honest, I have a shoebox full of pictures of my daughter waiting for me to get to someday. But if I wait until “someday” to continue taking pictures because I already have so many pictures I haven’t done anything with, then my daughter’s teenage years will come and go while I try to catch up. I don’t want to chronicle every detail of my daughter’s life (nor would she want me to!), but I was trying to think of some memories that she might want to laugh about and maybe even treasure someday. Ultimate Small Shop Guide Woodworking So how do you do that without ending up with pages and pages of memories? I decided to do two large (12×12) pages (facing each other in the album) for each year of high school.
“Just past the Decompression Zone is where you place fixtures known as Speed Bumps. These merchandise displays work much the same way as speed bumps in parking lots work—they slow customers down. They also grab their attention and introduce them to the cool product for sale in your store. Be sure to rotate the product on your Speed Bumps at least once a week.”
The more outlets the better! I have a good mix of 220v and 110v outlets throughout the shop. I even included a few in the ceiling and the floor in hopes of avoiding power cords in the walkways. And although this contradicts my previous comments about over-committing, I picked locations that would likely work for various tool configurations. If at some point they don’t work for my setup, I just won’t use them.
Since the summer of 2013, first time visitors to New York City restaurants have been greeted by window signs boasting a large, capitalized A, B or C. These letters reflect the rating given to each restaurant by the New York City Department of Health and Mental Hygiene (NYCDOHMH). Does the need for government oversight of this industry create an additional administrative and financial burden for the businesses in question? Yes it does. Does the rating system also inform consumers and encourage higher food safety standards across the board? Undoubtedly.

If you are looking to sell your business, it is important to engage a lawyer who is a business specialist to ensure you gain the best possible valuation. A small business is valued by assessing the potential ongoing income from the business over the coming few years. Normally this means that a business will be valued at three to five times net revenues, which can present a potential issue for particularly tax-savvy small business owners. Remember that every time you write off an expense against your business, you are lowering the net margin of the business. So, that dollar you saved by writing off the expense could cost you three to five dollars on the valuation of your business.
Other than that, you can’t have too much light — especially north light! — and you want accommodations for all the electricity you can imagine. Ceiling fans are a must. A good dust collection system is good, too. Don’t forget to plumb in for compressed air. Do NOT use hard PVC water pipe for compressed air — ever. If/when it breaks or ruptures, it explodes into tiny sharp glass-like shards. I know firsthand. I’ll tell you about it some other time. Think balloon popping!
We have Eclipse Sunshades installed on our van. While they’re pricier than the cheap sunshades you’ll find at Walmart, they’re every effective. And since they permanently install on your windshield they’re much more compact - a big plus for living in a van. All we have to do is pull the shades across and velcro them together in the middle and we’re protected from both the sun’s rays and prying eyes.
Starting to see a trend here? Notice how each of these questions begins with the customer in mind. As with all things related to your store, it’s critical to put your customer at the core of your decision making. At first glance, little things like cold drinks that aren’t quite cold enough, can seem insignificant, but it’s often the little things that hurt the customer experience and can turn a customer off to your business forever.
The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.

Remember, your retail store layout guides product placement, directs customer flow, and defines the overall look and feel of your store, so it deserves plenty of thought. Many factors will affect your floor plan choice, including the size and shape of your sales floor, the types of products you sell, and even the customers you hope to attract. Keep these factors in mind as we explore each floor plan option in detail.
Reflectix only works if there is an air gap next to it - Reflectix themselves recommend at least a ¾” gap between their material and the area to be insulated. This is the case because Reflectix is a radiant heat barrier, and when you put it right up against your van walls the foil cannot reflect back radiant heat (remember, radiant heat is only transmitted through air or a vacuum). If there is not an air gap, the insulating power of Reflectix is very low.

Reactions are typically over-the-top excitement. Everywhere I go, there are people snapping pictures, taking videos, and giving me a “thumbs up.” Sometimes while on the highway, cars will go ahead of me about a mile or so and then pull over to get out and video me driving by them. Truck drivers are always getting on the CB radio asking about the truck.
When you are looking for small business funding options, be it from the local bank, an angel investor, or even a family member, the first thing you will be asked to present after your business plan will be any existing financial records. Make sure you are putting your best foot forward by keeping meticulous records, with your business finances completely separate from your personal finances.
My husband is always hounding me about wearing eye protection whenever I use power tools. (Admittedly, I could be more diligent about it.) So, he recently glued some small magnets to several pairs of safety glasses and stuck them on all the power tools in our garage that have metal housings. Now it’s fast and easy for me to grab the glasses when I need them, and I’m reminded that my husband loves me. — Lisa Yanda. Here’s the other must have safety gear every DIYer should own.

For example, at a certain point, you will be asked to project how much cash you’ll spend in your fifth year of business. You’ll think, “Are you kidding? I haven’t even opened my doors yet and you want me to describe what my expenses and revenue will be like in five years?” Well, the quick answer is yes. Nobody ever said that starting a small business would be an easy feat.
Secondly, your size allows you to laser-focus your attention on the right audience. Walmart wants to sell everything to everyone. So maybe instead, you just focus on selling colorful earmuffs to children in the Mission District in San Francisco. This kind of clarity allows you to compete for search rankings on Google, key positions on Yelp and other business recommendation engines, and for space on social media.
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
I hope to build my own stand-alone dream shop sometime in 2015 – in the Texas Hill Country. I’ve not yet found the right lot, so much is yet unknown….but am thinking roughly 30′ x 40′ overall, with 10 or 12 foot ceiling. At one end, there will be a 10′ x 30′ space walled off into three spaces: a small finishing room, an office/design space, and a half bath.
Trademarking is a lot less expensive than most people think (although enforcement is another thing entirely), but make sure to do your research! If someone else is already using your proposed name, your application will be rejected right away and you will not only lose your application fee, but the time invested would have been in vain. And as you know, time equals money.

In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
I used to coat my metal table saw and planer bed with auto wax because it makes the wood slide nicely across the metal. But then I saw an expert cabinetmaker use wax paper, and now I do the same. I keep a roll in my shop drawer and rub a sheet of it over the metal beds on my table saw, router, planer and disc sander. The wax coating doesn’t last as long as a good paste wax, but boy, is it a lot easier and quicker. — R.J. Hayes. Plus: 22 clever new uses for your tools.
It’s tempting to place new products, hot items, and sale signage front-and-center so they’re the first things customers see upon entering. But don’t do this! The first few feet inside the door, say five feet for a small store, and 15 feet for a larger store, is known as the decompression zone. Store design experts strongly advise against cluttering up this space.
The other aspect that separates the cost of ecommerce apps is the payment itself. As users add products, they'll need to check out and perform a payment transaction. Some of the tools above bundle in payment solutions. Alternatively, you'll have to integrate with payment gateways like Stripe, Braintree, Authorize.net, etc. Ecommerce apps that fall into this category include Amazon, Stitch Fix, Honest, and many others.
In many ways, skoolies are the ultimate in mobile living. The big advantage here is space - there’s tons of room for couches, beds - even a full bathroom - and you can easily accommodate families and other larger groups. There are also some really impressive skoolie builds out there that are nicer than actual houses, and it’s a whole lot cheaper to convert a bus than to buy a similar-sized RV. Skoolies come in multiple sizes, from “shorties” to full-sized buses.

Can you outfit your shop with all the necessary hand tools for just $100? Christopher Schwarz says you can, and he’ll show you how to do it in this article. Take Christopher’s shopping list to the flea market and come back with everything you need for less than you’d spend on one new hand plane. You can do all your woodworking with hand tools, and this article from Popular Woodworking will equip you with everything you need.
As your business grows, your ability to deal directly with every customer diminishes, and your reliance on your staff increases. Indeed, for many businesses, such as full-service restaurants, hiring staff is an absolutely essential part of their operations. It is therefore important that you choose the right kind of employees and then take the time to fully introduce them to your mission statement. A really great employee should learn about your values and seek to embody them when interacting with your customers.

Dressing rooms are a must in most apparel stores, but they do take up valuable floor space. Make the most of dressing room areas by using adjoining walls for promotional items and accessories like belts and scarves. If you provide dressing areas, be sure at least one door and changing space meets the Americans with Disabilities Act accessibility guidelines, too.
7. Illuminate your space in different ways. Lighting is important in any retail shop, but it's particularly critical in tight quarters. If a corner of your store is not well lit, that square footage is as good as lost, Langdon says. She recommends using a combination of track lights, lamps, sconces and picture lights. This mixture will not only ensure that your entire space is well lit, but it also will add flair and variety. "Picture lights are amazing. They give a wonderful glow," she says. "Think in terms of layers of light."

We all know that we’re not supposed to judge a book by its cover. The truth is however, that it’s human nature to judge based on appearance. Though most of the time, despite our good intentions, it happens unconsciously. As consumers we make incredibly quick decisions about the businesses we choose or choose not to frequent. As we enter a location we take in the signage, the windows, and the product displays. And with the blink of an eye we determine a dozen different factors. Is this location trustworthy, clean, and friendly? Is the staff likely to treat me well? Will the products be to my liking? Will I find what I need and complete my purchase quickly? Can I even afford to shop here? And, perhaps most importantly: Is there something unique about this place?
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.

Sprinter vans have been around for awhile, but they’re still the new kid on the block. These vans are especially known for their interior height, long wheelbase, and boxier shape - making them ideal for building out a spacious, functional living space. This category includes the original Mercedes/Dodge Sprinters, as well as Ford Transits and Dodge Promasters (check out this article and this helpful graphic for more information on the differences between these).
1) I haven’t lived with another person sleeping in the back (where you at ladies?!). I have spent a few weeks here and there on the road with others, I slept in the back, they had their own tent at camp. It does get crowded having two people with full alpine kits sharing the same storage space. You have to juggle space and work together to get to things. As for two people sleeping in the back, I think that would be pretty tight (doable, but challenging). In my research (links in this post at the bottom) I know there were a few couples living in a shared truck bed…
This legal name is your first step in separating you and your business as two distinct entities. You will use your DBA name on all legal paperwork and government forms, such as applications for employer tax IDs, licenses, and permits. It is significantly harder to go back and have this applied retroactively, so it’s worth getting it right from the start.
If you have some experience under your belt, put it to good use as a life or career coach. Many of us are looking for guidance in our careers -- and finding someone with the time to mentor us can be tough. Life/career coaches don’t come cheap, but they are able to offer clients the intense and hands-on training and advice they need to make serious moves in their personal and professional lives. After all, sometimes everyone just needs some uplifting advice.
To experiment with different wood shop layouts, measure your furniture and equipment to sketch onto your plan in different positions. You can also make cutouts of the footprint of your items so you can easily move them around your floor plan to see how best to arrange them. As you do so, don’t forget to leave adequate spacing around tools and tables.
Compensation is a critical key to retaining and motivating the right employees. However, since small businesses often start out with tight budgets, compensation is an area they often struggle with, commonly leading to bad hiring decisions that affect overall business performance. The good news is that employers willing to step outside the hourly-wage box have a variety of options.

As a carpenter, I need to bring certain items with me every day. I bought a cheap plastic tote in the tool storage area at a home center and modified it for my needs. I made a small plywood deck, drilled a couple of 3-in. holes for coffee cups or glue bottles and then fastened it to the tote. Another piece of plywood has holes to keep pencils upright and organized. My tote sits nicely on my bench seat, but it could also be attached to the floor with hook-and-loop fasteners. You could easily customize these totes for plumbing, garden or painting tools, electrical supplies—what have you. — Don Simms. Check out this jumbo tote for fasteners.
Google - If you have any question in the world, you can google it and probably find the answer, lol. However, I know your concern is how accurate the information is that you are getting. You also want to make sure that when you find some great knowledge, that it's leading you in the right direction. So if you google "how to make money from my Instagram following" or "how to drive buyers to my Instagram account", then you want to find actually step by step instructions, that will actually lead to a real result. Sometimes that isn't always the case. So search and try to put the pieces of the puzzle together to help you, but just know that it probably won't be handed to you on a silver platter like my webinars are. If you are having problems with your SEO for google, then I recommend that you get my Google SEO Webinar.

With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
So before you start to consider fixtures and displays, think about the product positioning throughout your store. Where are your evergreen, seasonal, limited availability, and sale products going to be featured on an ongoing basis? This process is called product mapping. Following is an example of a product mapping plan that features a mix of product categories in defined areas:
The Best Prices for Tools – Ralph shows you where to get the beast deals for the tools and equipment you need. You could buy them yourself from popular outlets like Home Depot, Lowe’s, and Amazon, but the Ultimate Small Shop guide shows you where to get these tools and equipment at cheaper prices. Of course, cheaper isn’t always better. These aren’t just cheap tools that are ineffective. Just good value for money on good tools.

Once you’ve got that, you’ll want to familiarize yourself with your tax obligations as a employer, including providing required employee benefits such as social security and workers’ compensation. As an employer you are also responsible for withholding federal and state taxes from your employees’ paychecks. What’s more, you are obliged to ensure all withheld tax is forwarded to the government within a defined time frame (usually a matter of days after the paycheck was issued). Failure to do so can result in a fine.
In short – yes. The small business community is a diverse and eclectic collection of mom-and-pops, multi-generational businesses, one-stop shops, trendy boutiques, food trucks, lemonade stands, wine stores, bicycle stores masquerading as bars, and more. These entrepreneurs come from every walk of life and their motivations for starting small businesses are as unique as the businesses themselves. If you’re reading this, chances are you’re looking to join their ranks, and we say: “Go for it!”
Well this is the same unit I have used for years so the noise level will be what it has been. I never turn it on without ear protection. In the future, I plan on building a little closet around the cyclone to help mitigate the noise to some extent. As for cycling the motor, I read that too. But the way I work, I just can’t do that. I have to turn it on and off as needed but I do try to limit it as much as possible by doing all of my heavy milling at once.
An exclusive arrangement is one where the tenant works exclusively with one broker for a 3 – 12 month period. During this time, the tenant can’t work with another broker. A commission between the tenant and broker is negotiated, equal to a small portion of the expected tenant broker fee. However, this commission is paid only if there are no tenant broker fees.
Trademarking is a lot less expensive than most people think (although enforcement is another thing entirely), but make sure to do your research! If someone else is already using your proposed name, your application will be rejected right away and you will not only lose your application fee, but the time invested would have been in vain. And as you know, time equals money.
Compensation is a critical key to retaining and motivating the right employees. However, since small businesses often start out with tight budgets, compensation is an area they often struggle with, commonly leading to bad hiring decisions that affect overall business performance. The good news is that employers willing to step outside the hourly-wage box have a variety of options.
Check your local papers, especially the free shoppers, for information about upcoming shows Another venue for craft retailing is at the local flea markets that spring up in every community just about every weekend. Again the entrance cost is usually minimal. Ultimate Small Shop Result The only other thing you need is a little marketing savvy. With little cost and some effort, you will be well on your way to knowing whether there is a market for your craft. Once you know that, you can move on and think about other ways of selling, such as in galleries, on consignment, on eBay or from your own website. Once you spend your precious time and energy creating a scrapbook, make sure it lasts! There are a few simple things you can easily do to ensure that your scrapbooks look just as good as the day you finished them, for years to come. The first thing to avoid is paper that is not lignin-free. You’ve probably heard that before, and it is true, but what is lignin anyways? Lignin is a stiff component of a plant that quite literally holds it together. Although lignin is necessary for plants and trees, you want nothing to do with it! After a while, lignin will cause photos, fabrics and other paper that touch it to turn brown. Yes, the lignin-free paper does cost more, but it is a vital part of preserving your cherished scrapbooks. If the paper is not lignin-free, it will eventually discolor your photos and other materials touching it. So when buying paper for your scrapbooking projects, be sure to look for packages that say “lignin-free,” because if it doesn’t say it, then it most likely isn’t.The fabric is a big concern for preserving your scrapbooks, but unfortunately, it is often overlooked. Many people assume that all fabrics are acid-free, but they aren’t. Silk actually goes through an acid bath during the manufacturing process, as well as many tie-dyed fabrics. This isn’t to discourage you from using it, not all. Just try to make sure that no photos directly touch fabric, and if you need them to overlap, make sure there is a layer of paper between the two. Another consideration when using fabrics is if the color will bleed off onto your page and other things touching it. To test for this, cut a square inch off and soak it in a glass of water overnight. If there is no color bleeding from it the next day, then there isn’t any risk to your scrapbook. But if you do see color in the water, or collecting at the bottom of the glass then don’t use that fabric in your scrapbook at all. When using glitter, be sure there is a top layer of spray adhesive to lock them down, or better yet use special glitter glue where the glitter is mixed right in. If this is not done right the glitter will slowly fall off, and loose glitter means scratched photos. After you have planned the layout for your photos, be sure that you are using the right kind of mounting tape for them! Regular mounting tape is fine for buttons and bottle caps, but when it comes to mounting photos you need to use special photo mounting tape which is completely acid-free. Ultimate Small Shop Member If you don’t, your photos will slowly discolor. The tape should say “acid-free” right on the packaging.
Now nobody reasonably expects you to actually hit that exact number in five years time, but the point here is accountability. A really great small business plan forces you to think through your goals, associate a dollar value with each, and articulate clearly how you will make them a reality. By declaring your projected revenue in month seven or your expenses in year five, you are giving yourself a benchmark for success.
As always, great article! While my dirtbag adventure will likely only be about 6-7 months, I am starting to wonder about logistics. You mention that most people use the automobile they have. I drive a Prius. Not ideal for sleeping in, but I’m a pretty content ground dweller. I know that long-term I may start to question this. Here’s the proposition I’m considering: by saving on gas (45-50 mpg), I can occasionally cough up the money for lodging when I feel the need for added comfort. I can definitely do the number crunching, but I’m wondering if you’ve encountered people doing this or did similar analyses of your own at any point. I’d love to hear any insights you may have on this.
There’s a reason why some of the biggest players online have names that are essentially gobbledegook: Zappos, Skype, Zynga. While there’s certainly some psychological naming principles that often come into play, at the most basic level, it’s simply easier to find this space online and then strive to own the brand name in the minds of consumers. How important this will be to your small business will depend on a number of variables, including your intended size, location, and your desire to exploit ecommerce as well as a local brick-and-mortar business.
×