One tool that has been notably missing from the earlier builds is a router. There are so many reasons to own a router that I am not going to even try to list them. But if you want to get the creative juices flowing, take a look at this Pinterest page. The important thing to know is that this versatile tool can help you accomplish a number of tasks, everything from finishing edges to cutting dove tails.
The good news is that when you’re starting your small business, you now have the tools to take a data-led approach to choosing the right store design. For example: Not sure what type of music gets your customers in the mood to spend? Simply choose a few different styles and display a different one each week. After the test is complete, analyze sales data to help you identify what could be impacting sales. The key to getting accurate results from this kind of test is to avoid switching up the other variables in your store that can impact sales, such as signage, or testing one type of music during a regular business week and another type during a holiday week. For more details on how to create controlled in-store experiments, you can check out Lean Retail 101
A battery isolator allows your vehicle’s alternator to charge your auxiliary batteries while you drive, and keeps everything separated so you don’t drain your starting battery. Since we installed our Keyline Chargers Dual Battery Smart Isolator, our batteries are almost always fully charged. It’s also very simple to install - the toughest part is running the cable inside your van from the engine compartment.
One of the most important and often overlooked first steps when starting a small business is preparing a business plan. Many entrepreneurs who hear this might panic. And while the value of writing a business plan is often debated, those who complete them are nearly twice as likely to successfully grow their businesses or obtain capital compared to those who don’t. More on this in part three of How to Start a Small Business 101, Components of a Business Plan.
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
A grid floor plan, also called a straight layout, is a very efficient use of both floor and wall space. With fixtures and displays running parallel to walls, a grid floor plan maximizes every inch of available floor space, including the corners. Grid layouts are easy for customers to navigate and for store owners to categorize. Plus, they offer plenty of end cap and feature wall exposure for promotional items and seasonal products.
It looks great. Your little guy looks like he's having fun. I just had over 50 kids come through my shop last weekend to do some woodworking for cub scouts. I am saving left over insulation to put in there soon. I restocked my plywood recently too. The pieces of pipe made it much easier to pack in a lot of heavy pieces. I also took the time to measure lengths and mark the ends of all my lumber in the hatch under my bench to find what I need a little easier. My $100 8x8 needs a little TLC soon. But the shop is still rock solid. If you plan on making a lot of dust, I would also suggest a diy air filter with a box fan and a cheap air filter. It helps a little.
Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.
Store design experts agree that this area should be open, inviting, and free of overpowering displays and signage clutter, as shown in the image above. Many customer behavior studies, including those conducted by Envirosell’s Paco Underhill, support this opinion. They show that customers tend to ignore displays, signage, and even manned sales counters placed close to store entrances.
Congrats on a very nice shop. Great video to capture the moments. I too have moved around from place to place (in the Army) and I have to make my shop work with what they give me for a house. I’ve done work out of a tool shed and I make it work becuase I just love working with wood. Once I retire and settle in one spot I hope to get something similar to yours. I’ve picked up a lot of ideas watching this build.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
You may not have heard of Lemonade Freedom. It’s an organization set up after a spate of children’s lemonade stand closures by police who decided to take an absurdly heavy-handed approach to permit enforcement (you can read more about it in Forbes). Apparently the kids involved hadn’t applied for the necessary paperwork to run their stands. In one example in Georgia, three kids saving for a trip to their local water park had their endeavor closed down because they lacked the business license, peddler's permit, and food handler's license. Crazy? Only mostly.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
There are a number of woodworking fixtures you can get by without for a long while, but a sturdy workbench isn't one of them. The trouble is, those solid-hardwood benches we all lust after can completely blow a modest woodworking budget. Here's a bench that splits the difference. You'll get a top that can stand up to significant abuse, a sturdy, heavy base that keeps the bench planted where you put it, and an end vise and T-track system for holding workpieces as well as a variety of unique jigs. It may not look quite like a European bench, but it works just as hard as one for a lot less money.
Now this Super Pencil from C.H. Hanson does all of that and more. The entire pencil is made from a non toxic graphite composition so the whole thing is a writing surface with no wood around it to shave away. Super pencil marks are water and smudge resistant and because the composite is so durable it never needs sharpening even when you use it on rough materials like concrete.
One of the challenges we all face is how to move machines into a home without damaging the home, the machinery, or yourself. I actually had to bring things through the front door, and across hardwood floors, and turn 90° to descend the stairs into the shop. To protect the floors, I laid down sheets of 1/2" MDF that I could use later. On the wooden stairs, I used three strips of softwood strapping, held with wood screws to the stairs. I mounted a 2x4 baton to the wall studs at the top of the stairs, with a 5/16-inch eye-bolt through it.
We have Eclipse Sunshades installed on our van. While they’re pricier than the cheap sunshades you’ll find at Walmart, they’re every effective. And since they permanently install on your windshield they’re much more compact - a big plus for living in a van. All we have to do is pull the shades across and velcro them together in the middle and we’re protected from both the sun’s rays and prying eyes.
If you want to spend as little as possible on a vent fan, the Fan-Tastic Vent 1200 (about $130) is your best bet. This fan has three speeds and manual controls, and it has the same quiet operation and energy efficiency of Fan-Tastic’s other fans. If you find that you need to use it while it’s raining, it’s easy to add on an Ultra-Beeze Vent Cover later on.
Now, this is kind of an odd situation here, a few years ago when we bought this building there was a concrete block wall around here and a large drain right in the middle of the floor. Well the drain will certainly come in handy for any cleanup in the shop but the walls kind of left us when we removed those kind of left us a little divot and a little bit of damage here, so to make this nice and smooth so that our rolling workbenches will roll around real nicely we’re having to do a good bit of floor patch.
While we think a battery isolator and a 200-watt solar kit provide more than enough power for most vanlifers, some people may want additional ways to generate electricity and charge up their batteries. Especially if you’re planning on running power-hungry electronics like TVs and air conditioners, adding a generator and/or shore power hookups will help you deal with the extra load.
BEST ANSWER: Hi, I probably can't help, depending on where you are in the process. If the bench in the photo looks like it's just what you need, you should download the plan. I think Rockler has several ready to assemble benches that look quite good. Example: Large Workbench (N2000) Item #: 31719... I. too, am retired and trying to decide whether to buy or build. I have a bench that looks good and works good, but just is too light for hand work. It all depends on what you expect to be using the bench for. There are some good books out there to help us decide. "The Workbench" by Lon Schleining" is excellent. Also, Christopher Schwarz has written several good books on the subject. Vince, good luck and have fun working wood.