You might be thinking your business aspirations are too ‘early-stage’ to merit investigating the permits required to run your small business. You’d be wrong. The costs and requirements of staying on the right side of the law should be factored into your initial business plan and ongoing projections. In the long run, this will save you time, money and heartache.
This is where I started thinking about how I was going to store all of my lumber.  I had planned on building a wall rack, similar to what I had used in my single car garage.  But I hated using up an entire wall for lumber storage.  I also knew from experience that I would easily lay stuff against it and soon be digging lumber and junk out of my way.  I decided to use the space under my workbench to store the long boards and I realized that by pulling my bench out from the wall I could slide sheet goods behind it.  This created a problem:  How do I get it out.  The Shop isn't long enough to pull out 8 foot boards from inside and I would probably have to move things around to get to it anyway.  So my plan for this came at kind of a sudden epiphany moment, when I decided to cut access doors in the front and build my storage into my workbench area.  This has been the single best idea that has come out of my shop.  I can't express enough how easy it is for me to get straight to a board i need with no hassles.  I just remove the doors and pull out what I need.  I can store a surprising amount of lumber in this area.  I do have a secondary area for some cutoff sheet goods and a scrap bin next to my table saw in the garage.  But this area stores most of my lumber.
One site that I found a year or more ago was Life Remotely. They converted their truck to accomodate 3 people traveling from Seatle to the end of South America. They camped in tents most nights and some hotels/hostels but did a lot of conversions to their truck. Plus they blogged the whole time which is pretty cool if you want to take the road trip international.
Well I was just thinking about all of the supplies I’ll be able to keep in this large shelf unit we just installed in our workshop. Hey, that’s we’re doing this week is creating a very practical realistic workshop where we’ll be doing a lot of projects for the TV show, but it’s also going to be used by my construction company so it really has to be set up properly.
Whether you build or buy your workbench, it must be designed and constructed to withstand the rigors and pounding you’ll put it through. The base and legs should be sturdy and the table should not easily be knocked over. The top should be durable and not easily dinged or dented. Make sure your workbench is made of a material appropriate for your types of projects, too.
This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.
Equity financing is money raised in exchange for a share of ownership in your business. The core benefit of this type of funding is the lack of debt. You won’t have to worry about those pesky monthly repayments. The downside? You are giving up total ownership of your business, you are giving up the rights to a portion of the ongoing profits of the business, and you are potentially giving up some control of how your business is run (Though this is not always the case).
4. Avoid a cluttered look. Owen managed to add more merchandise but avoid a cluttered look by using neutral colors, such as ivory and gray for furniture and larger items. She then accented the space with smaller brightly colored items like vases and pillows. She also makes sure not to crowd her merchandise too closely together. "We try to make it look elegant and give it some space," she says.
Of course, if you’re going to build a sweet shop, you’re going to have to outfit it with an equally sweet bench. This afternoon I stumbled upon a UK bench-maker by the name of Richard Maguire. Built of kild-dried ash, Maguire’s benches are then finished with an oil and wax combination and feature twin screw vises which, while really interesting, might not be a perfect fit for everyone. While you can use these vises to apply more accurately distribute clamping pressure on different-sized stock, I could certainly see it becoming a wee bit of a pain when clamping stock that comes in contact with the entire length of the vise’s face. Having to equally screw in each side might frustrate some woodworkers. Still, these benches are a blast to look at.
Hey! Thanks for stopping by and checking this out, I appreciate your comments as well. It is something I really should do… I’ve done a bit more research on this since I initially posted it, and it is less intimidating the more I read. It just comes down to actually doing it and spending some more money, I guess. I’ve got the 22RE in my truck… I still need to look more into the alternator aspect though.

Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
The dream of a dedicated home shop is a common one among woodworkers. Whether you currently borrow shop space, work in your driveway or side yard, or compete for a corner of your basement with Christmas decorations or your fur­nace, you may be ready to build your own space that will allow you the free­dom of more room and time, and will also keep dust, fumes, and noise under control. Every design/build situation will be unique but there are a series of consid­erations that you will face in the design and construction phases of your project. Let’s walk through the process and dis­cuss the questions that you will need to ask yourself and others as you approach this project.
When Julie Owen bought Cocobolo Interiors in 2008, she set about adding more contemporary items to the Armonk, N.Y., shop. But with only 3,000 square feet, she struggled to figure out where to put her expanding line of furniture, lighting fixtures and accessories. Her solution: create sections within the shop and arrange the furniture the way customers might imagine it at home, using low bookcases and folding screens as dividers.
Store design experts advise small retailers to keep versatility in mind when choosing product displays. Your stock will likely change over the years. If you install permanent, unmovable displays, you will likely regret it later. Adjustable display options such as slatwall, gridwall, apparel racks, and shelving tend to be good choices for small retailers.
I totaly get not wanting to get into the cost part of the shop. We just went through a house renovation, and my stock answer to the ‘how much’ question is either ‘enough’, or ‘enough that was right for us’. There is a quality of life or utility aspect that every person needs to figure out for themselves. And, I would think not having to bounce around from garage to garage anymore has gotta be worth something!
If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.
When we started putting together our water system we decided to look for a stainless steel tank. Even though plastic tank options are FDA-approved for potable water use, we still don’t like the idea of our drinking water being in contact with plastic for extended periods. Sure, they say it’s “safe,” but not long ago water bottles containing BPA were considered to be safe.
When I change blades on my band saw, I usually need to adjust the thrust bearings and guides with an Allen wrench. I was tired of hunting around for the wrench, so I decided to stick it to the steel housing with a rare earth magnet (neodymium) about the size of a jacket button. Now it’s always handy! — Bill Wells. You can also use a magnet on your ladder.

This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.


It looks great. Your little guy looks like he's having fun. I just had over 50 kids come through my shop last weekend to do some woodworking for cub scouts. I am saving left over insulation to put in there soon. I restocked my plywood recently too. The pieces of pipe made it much easier to pack in a lot of heavy pieces. I also took the time to measure lengths and mark the ends of all my lumber in the hatch under my bench to find what I need a little easier. My $100 8x8 needs a little TLC soon. But the shop is still rock solid. If you plan on making a lot of dust, I would also suggest a diy air filter with a box fan and a cheap air filter. It helps a little.
One of the most important and often overlooked first steps when starting a small business is preparing a business plan. Many entrepreneurs who hear this might panic. And while the value of writing a business plan is often debated, those who complete them are nearly twice as likely to successfully grow their businesses or obtain capital compared to those who don’t. More on this in part three of How to Start a Small Business 101, Components of a Business Plan.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
In order to ensure that the staff you’re bringing on board is the right fit for your small business, there’s a few questions that you should ask yourself during the interview process. Are they competent? Capable? Compatible and committed to your core business values? Do they fit in with the culture you are trying to build? And can you offer them fair compensation? Business expert and entrepreneur Alan E. Hall, calls this the 7 C’s to hiring. At the end of the day you want to look beyond the skills and experience they have on paper and make sure that they are willing and able to grow with your business.
I bought an energy-saving outlet strip for my TV and its components. One outlet controls several other outlets on the strip, so when I turn off my TV, the adjacent controlled outlets for my VCR, DVD player and receiver sense that no current is going to the TV anymore, and those outlets shut off. Then I decided to try it out in the shop. I use it with my router table, disc sander and orbital sanders, so when I flip one of them on, my shop vacuum also starts up to take care of dust collection. It also has two outlets that are independent for other accessories you’d like on all the time. You can buy the outlet strips at amazon.com. One choice is the Belkin Conserve Socket with Energy Saving Outlet (about $30). — D. Linley. Plus: 30 more smart tips for working in your home shop.

Hey, I hope we’ve been able to share with you some ideas that you can use if you’re thinking about building a workshop or any type of hobby room or just about any room in your house that you can get this kind of enjoyment out of. We have a lot more details on this shop as well as other things you need to consider if you’re building a shop on our website at todayshomeowner.com. hey thanks for being with us.
As always, great article! While my dirtbag adventure will likely only be about 6-7 months, I am starting to wonder about logistics. You mention that most people use the automobile they have. I drive a Prius. Not ideal for sleeping in, but I’m a pretty content ground dweller. I know that long-term I may start to question this. Here’s the proposition I’m considering: by saving on gas (45-50 mpg), I can occasionally cough up the money for lodging when I feel the need for added comfort. I can definitely do the number crunching, but I’m wondering if you’ve encountered people doing this or did similar analyses of your own at any point. I’d love to hear any insights you may have on this.
Cutting thick, rough, warped hardwood can be cumbersome and dangerous. To provide some control over this process, I built a chop-saw station with wings that extend to support long boards. Again, anytime you make something that consumes shop space, make a shelf underneath to gain storage. The chop saw sits in a recess so that the deck of the saw is at the same height as the workstation deck.
Electricity was something we didn’t want to worry about at all in our van, so we went big from the beginning. We bought Renogy's 400-watt solar kit and two VMAX 155ah batteries. We mounted three of the panels on our van’s roof, and the fourth we attached to a folding stand made out of PVC so we could roll it out as needed. While the system works great and keeps us charged up, in hindsight it was a little bit of overkill - especially since we added a battery isolator.
Enter the garage heater. These space heaters are specifically designed to warm up wide open areas and to function under much tougher circumstances than you’re likely to find in the average house. A well designed garage heater will offer at least 5,000 watts of heating power — enough to warm 750 square feet of space. A smaller heater might take off a bit of the chill, but to really warm your workshop — and keep it that way — you’ll need a heater of this size.
You’ll also want to evaluate your obligation to your employees’ health care provisions following the introduction of the Affordable Care Act, which mandates the responsibility for the cost of insuring full-time employees to businesses with 50 or more full-time, or full-time equivalent employees. It also provides generous tax credits to smaller businesses with 25 or less full-time equivalent employees. Need a little more help understanding how U.S. health insurance reform affects your business? Register for one of the SBA’s upcoming Affordable Care Act webinars. They also offer recordings of previous webinars in both English and Spanish for those who can’t make it to one of their live sessions.
After years of digging through piles of stuff on my workbench for the air compressor accessory I needed, I had this idea. I simply drilled 7/16- in. holes on the underside of my workbench top and threaded in a few 1/4-in. NPT male couplings with quick-connect couplers. A wrench and some upward pressure are all it took to screw the couplings into the wood. Now I just snap my accessories onto the couplers when I’m not using them. — Donnie Dressler. These are the best tools for automotive work.
The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.
From a legal perspective, this lack of uniqueness doesn’t need to be a major concern. According to the rules governing business incorporation in most states, if you find yourself opening with the exact same name as another business, you can keep it as long as “your business and the existing business offer different goods/services or are located in different regions.”
The small apparel boutique pictured above really nails these traffic flow details! A roomy entrance offers clear sight and travel lines to eye-catching power walls on the right, and an inviting seating area towards the back. These lure customers into the store with the promise of treasures and comfort within. The shop even has a left-side checkout midway back. Someone really did their customer behavior homework on this retail store layout.
Remember the social media networks we asked you to secure in section five, Choosing a Business Name? Well, now is the perfect time to activate those channels. Use social media to build excitement about your grand opening and keep potential customers informed about special promotions and sales. People want to know what makes you special, so tell them why your store or restaurant will be different to what is currently available. From sharing pictures of that new fancy espresso machine or sneak peeks of your store’s interior, you can gain buy-in to your central message and build some anticipation before you even open your doors. Knowing how to to leverage key social channels is imperative to starting a success small business that will stand the test of time.
To make the most of your workshop oasis, look for a water dispenser that offers a choice between chilled and hot water. This will let you enjoy a cold, refreshing drink in the heat of summer rather than a lukewarm bottle that’s been sitting around gathering dust. You’ll also cut down on the amount of plastic your household goes through, which is a boon for the environment. In the winter, the hot water tap will also you to make a cup of tea or a mug of instant coffee on the spot. No matter what your taste, a versatile drink dispenser will keep you hydrated and happy while you work.
When Julie Owen bought Cocobolo Interiors in 2008, she set about adding more contemporary items to the Armonk, N.Y., shop. But with only 3,000 square feet, she struggled to figure out where to put her expanding line of furniture, lighting fixtures and accessories. Her solution: create sections within the shop and arrange the furniture the way customers might imagine it at home, using low bookcases and folding screens as dividers.

7. Illuminate your space in different ways. Lighting is important in any retail shop, but it's particularly critical in tight quarters. If a corner of your store is not well lit, that square footage is as good as lost, Langdon says. She recommends using a combination of track lights, lamps, sconces and picture lights. This mixture will not only ensure that your entire space is well lit, but it also will add flair and variety. "Picture lights are amazing. They give a wonderful glow," she says. "Think in terms of layers of light."
I didn’t want to get a truck with a million miles on it. I am not a trucker by trade; I got my CDL specifically for this project. I didn’t want to get into a truck and then have to worry about its structure, engine, and transmission—and then start building Optimus on top of it. That’s why I got a brand-new truck custom-built from Western Star to become Optimus Prime.
Whether you build or buy your workbench, it must be designed and constructed to withstand the rigors and pounding you’ll put it through. The base and legs should be sturdy and the table should not easily be knocked over. The top should be durable and not easily dinged or dented. Make sure your workbench is made of a material appropriate for your types of projects, too.
You can see in this step how I notched each rafter to fit more securely to the walls.  I also used a metal hurricane strap to secure each rafter to the wall.  Even though this was not required by code, I felt my tools were far to valuable to be left to chance over such an inexpensive solution.  The walls are a simple board and batten system.  The 1x3 trim covers the joints of the 4x8 OSB.  They make much more high quality sheets goods to use as siding.  However, the cheapest I found was $35 a sheet and the OSB was about $5 a sheet.  I sealed the OSB and painted it with exterior paint.  If I run into problems in the future, I can just add a second layer of more durable material or simply have siding installed.  It has held up very well over the past couple years and I see no need to spend more money on it now.
It all depends on what you care about most. Putting your kitchen by the side door could simplify refilling your water and propane tanks. Putting it behind the driver’s seat creates a nice, open feel in your van. Right behind the cab makes your van more private, while all the way in the back is a different twist on most van layouts out there. Some vanlifers even have kitchens that pull out of the trunk on drawers for cooking outside.
Make sure to run ground wires wrapped around all lengths of flexible exhaust hose to prevent static build up, which can spark and potentially ignite. I chose the King 1.5 HP dust collector, with a 115 volt motor, so I did not need special wir­ing for it. A shop vac is a must, as well, used to vacuum out machinery, and to remove dust from furniture prior to fin­ishing. Finally, an air filtration system was installed to clear the air of tiny airborne particles. The King KAC 650 unit I installed does a nice job, has a remote control, and a program­mable delay – I usually have the air cleaner run for a timed two hours when I leave the shop.
“Beware suppliers bearing gifts. That ‘free’ refrigerator from the drinks supplier is never really free. You can quickly find yourself tied into sub-optimal deals because of a reliance on this hardware. If you have access to the capital, do yourself a favor: Buy your own fridge and negotiate from a position of strength.” — ShopKeep Founder and Experienced Small Business Owner
However, another critical component to small business success is being self aware. With a variety of tools at your fingertips, tracking basic accounting can be fairly simple. Still, in order to be strategic about how you spend your money, properly leveraging these tools will still require a little bit of legwork. What used to take you eight hours might now only take one hour. But if you’re not willing or able to run through your financial tasks on a regular basis, bringing in a bookkeeper or accountant might be your best option.
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!

All this is why I recommend you buy the very best stuff available, even if it means going without certain tools initially. Although it wouldn’t be a disaster to spend $1000 on a whole bunch of inexpensive tools, what are you going to do when you’ve outgrown the capability of these tools and want to upgrade? You’ve now got to somehow get rid of the cheap stuff and replace it with something better. This isn’t easy and it’s always the most expensive way to go.
First, as most eager but hesitant potential hobbyists realize, you have to be much more thoughtful about tool selection. A 14-inch band saw? In your dreams. In a small space, you're going to have to rely on bench-top or handheld tools. (It is possible to forgo power tools entirely in favor of hand tools, but that's a discussion better left for another time.)
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
Once you have an idea of your store layout and a product mapping plan, it’s time to consider your store fixtures and displays. Fixtures are permanent—fixed—parts of your store such as lighting, counters, fixed shelving units, and dressing rooms. Displays hold product and tend to be movable, versatile, and customizable, like modular units, gondolas, tables, slatwall, and clothing racks.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
In our opinion, the best kind of fridge you can get for a DIY campervan is a portable 12V fridge/freezer. These fridges are built for adventuring on 4x4 vehicles and boats. They’re very rugged, and they don’t need to be kept perfectly level like mini-fridges. They can run off 12V power or regular 110V. They keep your food as cold as you want, and they can operate as either a fridge or a freezer.
You’ll also sometimes want to walk a property with a licensed contractor. This is because some commercial spaces require lease build outs, which are necessary additions or improvements to the space. Build outs can be fully or partially covered by the landlord. It’s important in this scenario that you get an accurate renovation estimate and negotiate a build out into your lease.
While an electric miter saw is a convenience, it is not necessary to do good work.  A quality electric miter saw will run around $150-$200, that by itself would destroy our budget.  A hand saw with a miter box does the job just as well at a fraction of the price.  This highly rated Stanley version for ~$60 should get the job done, albeit with a bit more elbow grease.

“Just past the Decompression Zone is where you place fixtures known as Speed Bumps. These merchandise displays work much the same way as speed bumps in parking lots work—they slow customers down. They also grab their attention and introduce them to the cool product for sale in your store. Be sure to rotate the product on your Speed Bumps at least once a week.”

Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.


Another flexible option is the portable work tables the guys are building back in our shop. This gives us a work surface that we can move wherever we may need it. Now the main workbench we’ve left a little gap between two of the cabinets for a trashcan or a stool to slip in but we did need to support the countertop where it crosses so Tim and Chris are adding some 1x4s to bridge the space. They’re also putting in a 2×4 inside one of the cabinets where the two pieces of plywood will have to be seamed. Then it’s just a matter of laying in the pieces in place and nailing them down to the cabinet. That trim strip around the edge is mostly for looks but the cedar backsplash along the back will keep us from banging up the wall or getting small items stuck between it and the counter. All in all it started to look pretty good.

Conversion vans have some pretty sweet built-in amenities, including high-tops for extra headroom. Many have comfy captain chairs, leather seats, mood lighting, TV/VCR, and a rear bench seat that folds down into a bed. If you’re not picky about your living situation, this could be all you need to get started. And if you gut it and customize it yourself, the high top offers tons of great storage options that other vans just don’t have.
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but out­side the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials move­ment. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
This is a great project if you carefully consider your needs first. I left out the vise and tracks, but had no problem hand picking good 2x4 stock at the big box stores. I did use maple on the top sides in case I ever decided to add tracks, but it was not a budget buster by any means. The cabinet and drawers were a first for me and a great learning experience. I also added retractable casters so I can easily move the workbench around my shop. Love the workbench!
Congratulations !! I think 62 days is quick ! thats a big project. Now that its done and you got to get everything else set up it kinda sucks that you will also need to start making the payments, yuck. However I think it will be a good investment as your show continues to grow . I certainly love it ! I look forward to what you have in store. Thanks
Household vacs are not designed to handle large quantities of sawdust or wood chips. Their filters clog up quickly, greatly reducing suction. While you can get away with using a small cordless vacuum for small messes, a shop vacuum offers greater power and capacity. Whether you already own a shop vacuum or are shopping for your first, consider purchasing disposable bags or a washable and reusable CleanStream filter.
At times, while you are starting a small business, it will seem like there is a brick wall in front of you, made up of all the different problems that will occupy your time and mind: a lack of funds, permits, regulations, tax worries, inventory issues, or a lack of customers. Concepts like “free time” and “the weekend” will take on a very different meaning. While the emotional ups and downs of cash flow management and customer service, may drain your will to live.
It’s tempting to place new products, hot items, and sale signage front-and-center so they’re the first things customers see upon entering. But don’t do this! The first few feet inside the door, say five feet for a small store, and 15 feet for a larger store, is known as the decompression zone. Store design experts strongly advise against cluttering up this space.

Hey Melody, thanks for the email. I’ve traveled through some extremely humid areas (Central America)… I’m taking it that your canopy does not have a headliner? That in and of itself helps a great deal. Personally I would be hesitant to put holes or van roof vents in my cap, but that may be what you want to do. I would try sleeping with a portable personal fan first and see how that helps with the condensation issue. For me it worked wonders while sleeping in those hot and humid environments. I ran mine off the inverter connected to my secondary battery.

It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
Great website! I spent a summer living out of a ford focus hatchback while road tripping around the United States. The rear seats were replaced with a small platform to store gear and the rear windows were tinted. I enjoyed the freedom that anywhere I parked no one would see me hop from the drivers seat to my platform for some zzz’s. Also no one would guess that someone is sleeping in a 3dr ford focus.

Woodwork in all its forms is an enormously popular hobby amongst enthusiasts of all ages. Most people, regardless of their abilities, just like to tinker with a bit of wood and make something. Starting out should be easy but the misconception can be that you need a fair amount of space to begin. The fact is that many people create versatile workshops in the smallest of spaces. One in particular we like is Stephen’s 8×6 Workshop as he manages to cram an army of tools into a tiny area in a systematic and neat way.
You might be thinking your business aspirations are too ‘early-stage’ to merit investigating the permits required to run your small business. You’d be wrong. The costs and requirements of staying on the right side of the law should be factored into your initial business plan and ongoing projections. In the long run, this will save you time, money and heartache.
This is a fundamental question. A good place to start is with a survey of your property. Most municipalities have a maximum percentage of your lot that you can build on and standard setbacks from your property lines that you will need to adhere to without needing to request special permission to build. On a photocopy of your survey you can draw in what your local setbacks are in order to define the location within which you will be permitted to build. In a best-case scenario, you will have the space to build without compromising too much on space or location; otherwise, you may need to request a minor variance, which would allow you to circumvent an obsta­cle such as a setback.
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
If you are looking to sell your business, it is important to engage a lawyer who is a business specialist to ensure you gain the best possible valuation. A small business is valued by assessing the potential ongoing income from the business over the coming few years. Normally this means that a business will be valued at three to five times net revenues, which can present a potential issue for particularly tax-savvy small business owners. Remember that every time you write off an expense against your business, you are lowering the net margin of the business. So, that dollar you saved by writing off the expense could cost you three to five dollars on the valuation of your business.

This is a fundamental question. A good place to start is with a survey of your property. Most municipalities have a maximum percentage of your lot that you can build on and standard setbacks from your property lines that you will need to adhere to without needing to request special permission to build. On a photocopy of your survey you can draw in what your local setbacks are in order to define the location within which you will be permitted to build. In a best-case scenario, you will have the space to build without compromising too much on space or location; otherwise, you may need to request a minor variance, which would allow you to circumvent an obsta­cle such as a setback.
The idea of not having your own bathroom nearby can be incredibly intimidating, but we’ve found that this is actually one of the easiest parts of vanlife. Public restrooms are plentiful throughout North America, and we’ve never not had a bathroom when we needed one. Gas stations, truck stops, Walmarts, McDonald’s - you name it, we’ve done some business there.
Nicole and I decided not to go public with the cost of the build. Although we are very open about most things, we are a little uncomfortable about making an expenditure of this magnitude public knowledge. Furthermore, unless you live in the Phoenix area and plan on building the same size shop with the same patio and with all of the same finishing touches and labor requirements, the price isn’t all that helpful to you.
Now nobody reasonably expects you to actually hit that exact number in five years time, but the point here is accountability. A really great small business plan forces you to think through your goals, associate a dollar value with each, and articulate clearly how you will make them a reality. By declaring your projected revenue in month seven or your expenses in year five, you are giving yourself a benchmark for success.

It’s no accident that some of the best marketers in the tech startup industry are known as “growth hackers.” Think about your target demographic (e.g. students, local mothers, teenagers) and find any way you can to get the word out to them. Email mommy bloggers, hand out free samples at the local college, or write your website on all the napkins you hand out with your food. There is no substitute for action.
Thanks for the quick reply. Sounds like you haven't had any big problems with the moisture. I'm in NoVA too, so that bodes well for me. I was considering finding some tyvek house wrap or something to go around the walls in addition to a plastic vapor barrier under the floor, but it sounds like that is not going to be necessary. I was also thinking I'd try to find a window AC unit to use like you did. I like how you mounted yours up high.
To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
Equity financing is money raised in exchange for a share of ownership in your business. The core benefit of this type of funding is the lack of debt. You won’t have to worry about those pesky monthly repayments. The downside? You are giving up total ownership of your business, you are giving up the rights to a portion of the ongoing profits of the business, and you are potentially giving up some control of how your business is run (Though this is not always the case).
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.
It’s tempting to place new products, hot items, and sale signage front-and-center so they’re the first things customers see upon entering. But don’t do this! The first few feet inside the door, say five feet for a small store, and 15 feet for a larger store, is known as the decompression zone. Store design experts strongly advise against cluttering up this space.

In the summer months, your windows will be one of the primary ways that heat gets into your van. Because of its reflectivity, Reflectix works great as a window covering to reflect radiant heat away from your windows. And, if you’re concerned about height in your van, layering Reflectix under your subfloor is a good way to add a little insulation (R-1.1) without sacrificing headroom.

Tired of holding a flashlight between your teeth while working in the dark? Make a light stand by bending a 2-ft. section of 12- or 14-gauge electrical cable into a U shape. Duct-tape the light to the ends of the cable. The wire can be shaped into a hands-free supporting base for the flashlight or bent into a hook for hanging. — Paul and Haylee Lytle. Check out another hands-free light hack.
We use this fan for extra circulation when it’s hot, and to get the air moving when it’s cold at night and we have all the windows closed. We also keep it on for our dogs while we’re driving. There are cheaper 12V fans out there, but generally the cheaper the fan the more power it draws. The Endless Breeze is a great little fan, and it’s definitely worth getting for the added ventilation.
×