Hey Marc. Just wanted to send a huge congrats your way for this milestone. It’s been pretty awesome to follow you on this journey since I discovered you on iTunes some 5 or 6 years ago. Mad props for what you’ve done to grow and enhance the online woodworking community as well as woodworking as a whole. I think with todays generation (as well as future generations) growing up behind a computer, the work that you and the rest of the podcasting world do will go a long way towards bringing new people into the craft. I hope that in the future you are able to start a series of videos showing how you introduce Mateao to the craft. Keep up the awesome work!
Now also we have some shelves that we built here above this, little cubicles like this work great to organize your workshop so you can have different tools or different supplies in the different little areas. And we’re about to install a very simple countertop. Now this is nothing more than just three-quarter-inch plywood and we decided to stain it instead of painting it, because you know it’s going to take a lot of abuse with all the pounding and the dings, and dents you’ll get in a workbench so staining it and then sealing it with a coat of sealer will probably hold up better than anything else. Now we’ll put another coat of sealer on it after we finish the front edge band and the backsplash and once all of that is complete, boy this thing is going to work nice.

Store design experts agree that this area should be open, inviting, and free of overpowering displays and signage clutter, as shown in the image above. Many customer behavior studies, including those conducted by Envirosell’s Paco Underhill, support this opinion. They show that customers tend to ignore displays, signage, and even manned sales counters placed close to store entrances.
If you don’t have the time (or interest!) in building your own conversion but you still want to give van life a test drive, we’ve got an idea for you! We’d recommend getting a rental vehicle from Escape Campervans. They have 10 different locations across North America and come fully loaded with all the gear you need for an epic road trip. Plus, their rates are fair and affordable.
Great instructional! I built the bed of my 92′ Toyota pickup ext. cab the same way you did. I did some hard searching and found this camp pad, which literally fits the 40″ wide sleeping space perfectly. A few different mats from Exped will fit, but here’s the one I bought. Just thought you might like to know there’s an inflatable duo sleeping pad out there that works for your setup!
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
Tight control of inventory, while not a particularly glamorous part of owning a small business, is therefore one of the most important ways you can impact profitability. The good news now is that there is an array of technology available that can make this whole process much smoother, including sophisticated forecasting tools that will help you predict your required inventory levels for each day based on past sales, weather records, and many other factors.
Do you create, collect, or curate anything special? Consider starting an ecommerce store and turning your hobby into a full-time job. Whether you need somewhere to sell all that pottery you’ve been making, or an excuse to search for the sports memorabilia you love tracking down -- an ecommerce store can make it financially viable for you to pursue your passion.

Since grid layouts are used in most grocery, big box, and convenience stores, they create a familiar feel to customers. However, due to this familiarity, they tend to impart a grab-and-go experience. A grid layout can be a good choice for small retailers who shelf-stock inventory in quantity, like toys, books, magazines, specialty foods, kitchenware, and home goods. However, it’s not ideal for retailers who want to create an upscale, branded environment that invites relaxed browsing.


At some point in the process of starting a small business, it’s pretty much guaranteed that you will hear the following statistics (or variations thereof): 25% of new small businesses close their doors within the first year and 60% are gone within three years. The exact numbers here may vary, but the message is all the same: be afraid, be very afraid!
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
​There are some diverging paths that you could take at this point: some may want to get a router with a router table for edge work and improved joinery capabilities, some may want to start looking at some of the interesting 3rd party jigs - two of my favorites are the DowelMax and the Kreg Pocket System, but my recommendation would be to equip yourself to buy cheap stock.
At a time when you’re focused on getting in front of customers as quickly and as often as possible, it can be hard to think about official requirements like registering a business name or deciding on a legal structure. Still, now that you have decided to start a small business or buy an existing one, one of the first critical steps is determining the business entity that's right for you.

One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appro­priate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with hom­eowners and builders to make sure that the work will meet code and will endure.
Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.
While a single great product can’t usually support a whole business, it is beneficial to select one or two “headline” products that will form the cornerstone of your offering. This will often be an obvious choice: If you’re a coffee shop, your headline product will be coffee. If you’re a burger joint, you guessed it, it’ll be burgers. This product will often be the centerpiece of your marketing efforts and a way for you to “own” a space in a customer’s mind. For example, Jack’s Burgers makes the best cheeseburger in town and Daisy’s Threads has the most adorable scarves. 

One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.


I don’t own a dog, but I have taken my buddy’s two dogs out with us to the trailhead at least. Not sure that I have great recommendations for how you would go about living in the truck with your dog. All we really did was lower the large wooden deck to the bottom position, throw down some soft doggy beds and pillows, then cover it all with a giant blanket which also covered like the side bins to keep dog hair from getting all over. It was nice and cozy for the dogs while driving down the road. Then we just put packs and other gear on/in the side bins. We used some big metal clamps to secure the blanket to the side bins and keep it from falling down or sliding around. I would think avoiding any carpeting would be a good bet, just go with blankets and things than can be taken out, cleaned, and you can sweep out the back.
Whether you build or buy your workbench, it must be designed and constructed to withstand the rigors and pounding you’ll put it through. The base and legs should be sturdy and the table should not easily be knocked over. The top should be durable and not easily dinged or dented. Make sure your workbench is made of a material appropriate for your types of projects, too.
I save all my back issues of The Family Handyman magazine and love the projects and repair tips. The trouble is, I’m not always ready to do the project when the issue arrives. To make my favorite articles easy to find at a later date, I put a stick-on label on the cover and then add notes for easy reference when the time comes to do the job. — Willie Schreiber. Plus: Check out this small workshop storage solution.
This OXO palm brush really helps us conserve water while washing our dishes. We fill the reservoir with water and a few drops of Campsuds, and we only squeeze out what we need - so it takes care of both the initial rinse and getting our dishes soapy with minimal water usage. It’s also very compact, and the comfortable shape makes it easy to scrub dishes.
It’s hard to overstate the importance of choosing the right location when starting your small business. We’re sure you’ve heard the saying 1,000 times before, Location, Location, Location! Some of the world’s most well-financed franchises have this weaved into their business DNA. McDonald’s Ray Kroc is the perfect example. When asked about the business, this well-know American businessman and philanthropist once stated, “We are in the real estate business, not the hamburger business.”
We first obtained legal permission from Hasbro [which originally developed the Transformer toy line back in the 1980s] to build it late in 2015. I also had to obtain my commercial driver’s license (CDL), so I spent a few months learning how to drive a truck while simultaneously spending the winter of 2015-16 working with Western Star to piece together on paper a vehicle that mirrored the Optimus Prime truck. Once the factory delivered the truck in April 2016, we got to work on the customization and fabrication right away. It was roadworthy again by October 2016. So the entire process from start to finish was about a year.

I know in Missoula the garbage men do not like unbagged dust chips. They sent my friend a warning notice in the mail. Do you pull your drum out to the garbage and let the dust fly or dump it into a bag? My friend has garbage cans with 33 gallon liner which he pulls out of a sealed dust collection box beneath the cyclone… then he uses a hand truck to haul it out to the alley and then puts a fresh can in the box. It seems like a simple dust management method by not handling the dust by either scooping or dumping it out into a bag. I am always trying to think of ways to have less contact with harmful dust particles and I am curious as to how others handle the situation. Have a great weekend!
If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.
Remember that you must allow three feet of pathway space between all display units to meet Americans with Disabilities Act (ADA) requirements. But customer comfort is more than a requirement. Studies have proven, time and time again, that customers do not like to be jostled when shopping. Allow generous pathways between fixtures. Experts recommend three feet, six inches, so customers can move freely, examine products, and carry items to your registers. This will keep customers happily browsing in your store and you in good standing with the ADA.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
Whether you plan to go it alone or hire a professional, there are many resources available to help you plan and execute your retail store layout. If you don’t feel comfortable tackling the project yourself, a professional retail store planner, interior designer, or display designer can turn your dreams into reality. Or if you want to handle it all yourself, store planning software and other online idea resources can make the job easier.
Well, we’ve managed to put together the workshop I’ve always wanted. One that’s practical, functional and neat, well at least for the moment. We have plenty of light, plenty of power, lots of work surfaces and enough cabinets, shelves and hangers to organize all of the tools we’ll be using here. I’ve even managed to do a little creative workshop decorating along the way to remind me of how I got started in this business in the first place.
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
Setting up and running a small business is awesome, especially if it’s your first business. Is it tough at times? Yes. But if you don’t build your dreams, who will? In 2010, according to the U.S. Census Bureau, there were 27.9 million small businesses nationwide. This number has trended upwards over the last decade, accounting for 64% of net new jobs created between 1993 and 2011. In a world that appears to be dominated by today’s retail giants, it’s easy to overlook the huge impact that starting a small businesses can have on our U.S. economy. However, these numbers illustrate something that we strongly believe at ShopKeep – that the brave folks who open new businesses are the backbone of the nation’s economy and the lifeblood of our local communities.
Chris Marshall: You’re asking a question that would take many magazine articles or a whole chapter of a good shop-design book to answer adequately. If you haven’t already done so, you might also want to ask this question to the good folks that frequent our forum on woodworking.com. Every woodworker with a shop will have a slightly different answer, so here’s mine. I’ve never had a brick shop, but my last one was a metal pole barn (30 ft. x 40 ft.). I outfitted the interior with 2×6-framed walls and plenty of insulation. It stayed reasonably cool in the summer and warm in the winter, using a wall air conditioner and a 60,000 BTU furnace. Currently, I have a 24 ft. x 42 ft. garage space for my shop. It is framed conventionally with 2×6 walls and stick-built 2×10 rafters. I’ve only been in my new shop for about a year, but it is working just as well or better than my pole barn did, because the new shop has many large windows that let in lots more natural light. I’ve used 8-ft. fluorescent T8 light fixtures in both buildings with good success, and I ran both 110- and 220-volt outlets all around the room. The last shop had a plywood floor; the current one, a concrete slab. I thought I would notice a bigger difference between the two flooring types, in terms of how tired it makes my legs by the end of the day. But in all honesty, a good pair of supportive shoes seems to make the difference moot for me. Both types of buildings benefit from a dehumidifier during humid months (when I’m not running the A/C, that is) to keep the relative humidity low and my tools rust-free. If all things were equal, and money were no object, I would probably go with a conventionally framed wood building over the pole barn. It was easier to build that from scratch as opposed to retrofitting the pole barn framing with walls afterward. But, as I say, the next woodworker will probably offer you a completely different answer from mine. Good luck in your decision!

The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself).
Make sure the room or building you are planning to utilize has sufficient lighting and electrical outlets to allow you to see what you are doing, and to work without excessive extension cords. You should also remember that many tools require a fairly substantial amperage to operate, so you need to make sure the wiring is capable of handling the loads. 20 Amp circuits will work for ordinary 120V tools, but air compressors and welders may require 40 Amp, 220V circuits.

In each case, we shuffled the bench, jointer, table saw, and band saw across to the top of the stairs, and then tied a rope around each to act as a safety while sliding the machines down the strapping on the stairs. Yeah, the table saw hit the wall, and the promise of a good mud and paint job saved my bacon. The rope worked well, and we were able to get everything down the stairs nice and slowly with­out any major issues.
Before you buy a single tool, you need to take a hard look at your workshop space. If your workshop is a freestanding building or empty barn, you can simply measure the perimeter and know that you have the entire square footage at your disposal including the wall space. If your workshop is tucked into the back of a garage or a corner of partially finished basement, you’ll need to plan your furnishings with cars and water heaters in mind.
Many retailers are also opting for digital signage. While digital signage and display solutions are more of an investment upfront, they allow you to quickly and easily show customers sales, new products, upcoming events, customer reviews, and more. Mira Digital Signage is a popular digital signage option for small businesses that is easy to use and offers affordable monthly payments. Click here for a free demo.
Just stumbled across your article and it’s right on time as I am about to launch a special events venue (ballrooms, meeting rooms, outside garden area, outsourced caterer, etc). Not sure what type of zoning this business falls under. I read that zones are usually for office, retail, industrial and leisure. Any idea what type of zone I should be looking for? Also first time trying to get a commercial space for this type of business, any specific suggestions?
If you have the available time, taking your DIY campervan for a test run (or two) is a great way to identify any problems while you still have access to tools, package deliveries, and a place to work. There’s just a lot that you can’t foresee until you live in your van. Taking it out for some short trips throughout your build will help you understand how you’ll actually use your new living space, what’s necessary, and what’s not.
When leasing a retail space, there is always risks involved. Your goal should be to minimize these as much as possible by considering every angle and asking the right questions. For example, does the landlord intend on erecting scaffolding on the building at any point during the lease? If so, can the rent be reduced to reflect this situation? You will also want to ask to have a clause included allowing you to sublet if necessary, which can be important if you ever find yourself struggling to make payments.
A dust mask or respirator will protect you while you're working, but won't do anything to protect you or your family from suspended particles still in the air. For this reason, an air filter is an absolute must if you work with woods indoors (I know of guys who sneezed out sawdust after working too long without an air cleaner). It's possible to make your own air cleaner out of box fans and furnace filters, but retail air cleaners will usually be much more compact. If you go that route, we recommend Wen 3410 3-Speed Remote-Controlled Air Filtration System for smaller shops.

I spent a full week grading, compacting the soil and leveling each block before laying the floor joist.  The last thing you want is to finish your new workshop and have a corner start sinking into the ground.  My floor inside my shop is perfectly level still with a 6 foot level.  You can see that I had a drop of about 12 inches on the low side.  During heavy rainstorms, water can flow like a stream next to the fence.  I wanted to make sure my workshop was high enough off the ground to avoid any flooding issues.

So after 14 years in our previous location, my company moved to a new shop last month. My shop went from 1600sqft split into 2 bays with the kitchen in between to a contiguous 2950 sqft. Still don't know why the the office portion needed to grow by the same percentage when there were already 10 empty cubes at the old office, but thats an argument for another day. The boss got his 500 sqft office so he is happy.
An exclusive arrangement is one where the tenant works exclusively with one broker for a 3 – 12 month period. During this time, the tenant can’t work with another broker. A commission between the tenant and broker is negotiated, equal to a small portion of the expected tenant broker fee. However, this commission is paid only if there are no tenant broker fees.
Thanks for leaving a comment, Rob! I didn’t find that it limited where I felt comfortable camping, but I always tried to be discreet… Waiting until few if any people were around before I hopped in and usually peeking through the windows so I’m not hopping out right next to someone loading their groceries or whatever. I slept in all sorts of random places in that time on the road, more often than not it was in permissible camping areas, but there were other times it was more frowned upon–from grocery store parking lots, to auto repair places, etc. Certainly is more likely to guess that someone is camping in it, but I only got hassled once (by a rent a cop telling me to move on).
If you want to spend as little as possible on a vent fan, the Fan-Tastic Vent 1200 (about $130) is your best bet. This fan has three speeds and manual controls, and it has the same quiet operation and energy efficiency of Fan-Tastic’s other fans. If you find that you need to use it while it’s raining, it’s easy to add on an Ultra-Beeze Vent Cover later on.

The idea behind this segment is to find products that solve common problems we face as homeowners. And the cool thing for me is that I get to learn a lot about the professional side of home improvement. Well, I’m looking for do it yourself items. For example, do you know why carpenters pencils are shaped differently than ordinary round pencils? So they won’t roll off of an inclined surface like a roof. And the larger size allows you to draw fat lines as well as fine ones while you’re marking lumber.

Smaller speed bump displays (above) and larger merchandise outposts (below) placed along your store’s main traffic flow let you draw customer interest to certain products. Speed bumps let you feature new finds and hot sellers in eye-catching ways. Larger outposts are great for special price stock or product groupings such as seasonal features and branded collections.
Apps begin to get more complex—and costly—once user authentication is involved. The main reasons for that are all the other expectations that come with user authentication. Typically, they include interacting with data (e.g., favoriting an article), syncing data across devices, push notifications, and perhaps collaborative features (e.g., inviting a family member).
Hey! Thanks for stopping by and checking this out, I appreciate your comments as well. It is something I really should do… I’ve done a bit more research on this since I initially posted it, and it is less intimidating the more I read. It just comes down to actually doing it and spending some more money, I guess. I’ve got the 22RE in my truck… I still need to look more into the alternator aspect though.
As always, great article! While my dirtbag adventure will likely only be about 6-7 months, I am starting to wonder about logistics. You mention that most people use the automobile they have. I drive a Prius. Not ideal for sleeping in, but I’m a pretty content ground dweller. I know that long-term I may start to question this. Here’s the proposition I’m considering: by saving on gas (45-50 mpg), I can occasionally cough up the money for lodging when I feel the need for added comfort. I can definitely do the number crunching, but I’m wondering if you’ve encountered people doing this or did similar analyses of your own at any point. I’d love to hear any insights you may have on this.

​In order to excel you are going to need to read up on jig building so that you can produce consistent repeatable cuts.  Ideas for jigs are a dime a dozen online and you could easily lose a couple of hours browsing the hundreds of ideas people think up.  A more economical approach would be to build your jigs as your projects demand them.  After you go through that exercise 4-5 times, you'll find you've accumulated quite the collection of jigs without even trying.
Every shop should have good lighting, whether natural or artificial. My video work dictates limited natural light, so I was sure to have plenty of overhead T8 fixtures (6500k). You’ll hear me mention in the video that I was disappointed to see that the ends of the shop were just a little dark. Thankfully, I was able to get the contractor to come back in and drop in 4 more fixtures for me, two at either end. Now the light is bright, crisp, and evenly distributed from one side of the shop to the other.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 

Hey, I hope we’ve been able to share with you some ideas that you can use if you’re thinking about building a workshop or any type of hobby room or just about any room in your house that you can get this kind of enjoyment out of. We have a lot more details on this shop as well as other things you need to consider if you’re building a shop on our website at todayshomeowner.com. hey thanks for being with us.
Note: Some of the links to products that we recommend on this page are affiliate links. This means that if you click through one of our links and buy something, we get a small commission at no cost to you. This helps us keep this blog going so we can continue to provide you with van build tips, tricks, and guides. We believe in honest opinions, and we never recommend anything we don't know about. Every recommended product on this page we've either used personally, have personal experience with, or have researched heavily.
For example: Imagine walking into a slightly weathered coffee shop on Main Street, middle America. It’s charming in its own unique way. You sit down to enjoy a cup of coffee as you skim through the tabletop jukebox. Then the bill comes. “$10 for a cup of coffee? In this rundown joint!” This might be what comes to mind if the price of the service doesn’t meet the expectations you had when you first walked into the business.
Finally, think about the overall color and feel of your workshop. A fresh coat of bright white paint will help your lighting go farther, but you might also consider adding a splash of color for fun. An accent wall or an epoxy floor coating are good ways to upgrade your workshop from drab to fab without adding fussy decorations that will get in the way of business.

So before you start to consider fixtures and displays, think about the product positioning throughout your store. Where are your evergreen, seasonal, limited availability, and sale products going to be featured on an ongoing basis? This process is called product mapping. Following is an example of a product mapping plan that features a mix of product categories in defined areas:
One thing I found while looking on the topper websites is a piece of weather strip designed to go between the tailgate and the truck bed. It has a special wedge shape to it so when you close the tailgate it makes a watertight seal. It is just the thing to keep the dust and dirt from entering the back of your rig when driving down the dirt roads. They’re inexpensive too, for a full size truck like my Dodge it’s only $25. It has adhesive on one side, so installation looks simple.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
Nice video Marc. I did enjoy seeing the details of the construction process. Since becoming a homeowner and a woodworker (something that happened literally at the same time) I have become fascinated with anything having to do with the process of building and finishing and all the details in between. I thought of an off the wall question while watching this video and that is do you write yourself any kind of script for any of your monologues and/or narrating or do you just have a general idea of what you want to say and wing it?
Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on.  The rewards aren't usually good enough to compel me to purchase on their own.  But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.

You can also make your store comfortable by incorporating a waiting area with comfy seats and benches to encourage customers to spend more time in your store. This is especially helpful for shoppers accompanied by someone who isn't interested in making a purchase. But keep the seats or benches facing the merchandise so that they're still top of mind for those lounging around in your store.  
What about when you’re camping? Well, most campgrounds (including many free National Forest and BLM campgrounds) have some sort of bathroom situation. If there’s not an actual running water bathroom, you’ll typically find pit toilets (aka vault toilets), which are basically much nicer/cleaner permanent porta-potties. We also recommend picking up a good poop shovel for those times you’re camping in a wilderness area without bathrooms.
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
In our Complete Coffee Shop Startups Kit, we spend a good amount of time discussing your health department requisites, your coffee equipment, and even the design of your coffee shop. Since this makes up a significant bulk of your startup costs (equipment, space requirements, etc.), we recommend that you spend an extra couple of hours strengthening your knowledge base with listening to our audio interviews.

A great product line will also reflect a range of price points. For a business that is working hard to convey a sophisticated and elite vibe, it might be a useful strategy to set a high minimum price, but for the vast majority of small businesses, your pricing should be guided by one key thought: I want every single person who comes through my door to be able to find something that fits their budget.

The dream of a dedicated home shop is a common one among woodworkers. Whether you currently borrow shop space, work in your driveway or side yard, or compete for a corner of your basement with Christmas decorations or your fur­nace, you may be ready to build your own space that will allow you the free­dom of more room and time, and will also keep dust, fumes, and noise under control. Every design/build situation will be unique but there are a series of consid­erations that you will face in the design and construction phases of your project. Let’s walk through the process and dis­cuss the questions that you will need to ask yourself and others as you approach this project.

For example, on your dual battery, the farm just purchased a brand new 2013 Chevy 3500HD with a dump bed. It has dual batteries. How was it installed? They grounded both batteries to the frame and connected the positives with a very large fuse. ~15k later its still working. While its not recommended to do it this way, I think it would work fine in your case. Add the marine battery somewhere in your shell and run a heavy positive from the original battery. Put a large fuse in it(I’d research to see the number, I can’t remember off the top of my head) and your isolator switch inline (probably 2nd battery side of the fuse).
2) I haven’t spent very many nights in full on winter conditions (that 12 degree night in Boise comes to mind!), so I can’t comment too much. It was fine for that… Mostly it was hard transitioning from the warmth of the cab to the frigid air while you are shifting things around and getting ready for bed, but then once you were inside the canopy it was fine. Lots of frosty ice on the inside windows, but in my sleeping bag all was well. It stays a little warmer in the canopy. Maybe I’m a wuss, but I didn’t want to spend an extended period of time dirtbagging it in my truck while I was ice climbing (I spent the first two months in Ouray, CO, sharing a rental), I just thought it would be too challenging/miserable to dry and manage gear in a confined space with the shorter daylight hours. I’d be perfectly content doing future weekend trips with this setup though!
The good news? There are a ton of free tools out there help you simplify and minimize the research required to secure your online identity. Among them is Namechk, a free username and domain search tool that helps you discover the availability of your business name across hundreds of social networks and domain extensions, all at once. Once you run a name search and confirm that it’s available for use both off and online, take the time secure your unique name both legally and on the web.
A large table saw just isn't a feasible fit in most small shops. But you should be able to get away with at least a portable table saw. Never mind veteran woodworkers who might look down on these compact tools–they're well-suited for many of the smaller ripping and crosscutting operations you'll need to perform. Some of the more compact table saws, such as this 10-inch Skilsaw, are small enough to be stored in a closet or under a table.
The router—The router is the master when it comes to flexibility. Its potential far exceeds trimming and decorative edge treatments. A router will cut mortises, rabbets, and dadoes, and adding a router table builds in even more versatility, including biscuit joinery and raised-panel doors. But where the router distinguishes itself from all other tools is in its ability to produce identical parts using a pattern.
Hi, I have looked through pictures of the shop books. What I am interested in finding is a book with layout design options. I am ready to build a new shop for myself and want to put dust and electrical under the slab. Best layout designs would help me to figure out how to layout a shop that is aprox. 28'x 36'. Is there a book that has this type of information.
Meaghan Brophy is a retail writer for Fit Small Business. She has provided content and guidance for indie retailers for years as the editor for Independent Retailer magazine, a RetailWire BrainTrust panelist, and speaker at trade shows such as the Independent Retailer Conference and NY NOW. She has been quoted as a retail expert in Forbes, Retail Dive, Retail Minded, ASD Insider, and more. When not talking retail, Meaghan can be found watching dog videos and practicing her tap dancing skills.
If you want the ability to cook inside your van but don’t have a whole lot to spend, your best option is the Coleman Classic propane camping stove. For about $60 you get a sturdy and reliable 2-burner stove that runs off of replaceable 1-lb propane canisters. We’ve seen many people using these out on the road, and they do the job very well. Coleman has hardly changed the design of these stoves for decades, so you know they’re doing something right.

I framed in a 4x8 Garden Shed on the back.  I didn't want it so deep that stuff would get buried in it.  I need to take an updated picture of the back.  These pics were from early on and I have changed some things in the organization.  I used similar framing techniques and built a lean to roof attached with metal hangers.  I chose to use clear corrugated roofing to allow natural light into this shed.  You can see the 2 shopvacs that were originally part of my simple vacuum system.  I have removed them and found that I get better airflow using an electric leaf blower with the vacuum attachment hooked up to my system.  There is a large metal trashcan with a dust collection separator to collect the larger pieces of saw dust and chips.  My air compressor is on a shelf on the right now and I ran a hose through the wall and to a 25 foot reel attached to the ceiling.  I wired separate switched for both on the inside of my shop.  These systems work extremely well for a small shop.  The wall provides some insulation from the overwhelming noise they would otherwise create inside the shop.


Debt financing involves borrowing capital that must then be paid back over a set period of time, most commonly with interest. Typically the core benefit of this arrangement is that you, the business owner, maintains complete control over your business. Your only ongoing obligation is to repay the loan with interest. The downside? Fail to keep up those repayments and the loan — often secured against your assets, savings or property — can put you in very dangerous financial waters.
Thanks for the quick reply. Sounds like you haven't had any big problems with the moisture. I'm in NoVA too, so that bodes well for me. I was considering finding some tyvek house wrap or something to go around the walls in addition to a plastic vapor barrier under the floor, but it sounds like that is not going to be necessary. I was also thinking I'd try to find a window AC unit to use like you did. I like how you mounted yours up high.
While strolling through the recent entries to our online shop gallery, I spotted some pretty novel designs as well as a couple of fun videos worth taking a look at. From brilliant solutions for tight spaces, to novel repurposing of department store display racks, there were plenty of interesting elements to the eight shops listed in my February round-up. By the way, if you’ve already seen our art director’s video tour of his redesigned garage shop (Mike’s Garage Shop), you can go ahead and skip it. If not however, it’s really worth a look!
I used your set-up as a guide in building mine. It is a little different – it’s shorter a little bit, as I have a shorter canopy cover and I didn’t make the sleeping platform flush with the walls of the truck bed – but it turned out great! I’m really happy with it. Also, one of my favorite parts about it is none of it is actually attached to the truck. So I can take everything out and it makes cleaning a little easier. I’d post photos if I knew how. If you feel like seeing it let me know and tell me how to get them to you!

It is also essential to take a lean, data-led approach to choosing a business space. The average length of a commercial lease has dropped over the last few years but is still often well over five years, so the absolute last thing you want to do is rush into a signing and get locked into a bad situation. There are so many ways to test the viability of your business idea before you over-invest and sign a full-blown lease agreement.
The enormous range and affordability of options has provided the chance for small business owners to apply technology to their accounting, marketing, and day-to-day operations. You can spend less money, save valuable time, and gather data about almost every aspect of your business. What’s more, you can enhance the way your customers experience your store in a meaningful and cost-effective way.
Expanded polystyrene (EPS) is an open-celled foam board (think styrofoam) that is the cheapest of all the foam boards. It does work, but we generally don’t recommend using EPS in your van. It insulates less than XPS (R-4 per inch), and the gaps between the foam cells allow moisture to penetrate, which degrades the insulation over time. Polyiso and XPS are much better choices for a slightly higher cost.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
×