To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.
As Kizer & Bender always tell retailers: Put it on paper. If you haven’t settled on your store layout—or even if you have—the first thing you need to do is work your plan out on paper before you start moving things around in your store. Putting it on paper helps give you a clearer picture of the desired result and any potential issues before getting started. Remember, many small retailers find that a mix of floor plan and layout styles works best.
There you have it! Now you have no excuses, you must start planning right away. Please remember this can take a lot of time and a lot of work, so be sure not to stare at your task list in its entirety too often. I don’t want you to get overwhelmed knowing all the things you must get accomplished. Just focus on the goal that is the most important and attack it, task by task. Need help organizing these goals? Check out my Goal Planning Worksheets here:
It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
You can typically find paneling in pine and cedar. Pine is cheapest, looks fine, and will do the job. Cedar is more expensive, but it looks and smells awesome - and it’s resistant to mold and mildew. Paneling comes in different thicknesses, but we recommend using ¼” (5/16”). Thinner paneling weighs less, costs less, takes away less interior space, and will bend with your van’s contours.
Just a quick note about light spectrum. I went with 6500k because that’s what I like to film in. The daylight spectrum makes it easier for me if I decide to open the blinds, letting in some natural light. For the average woodworking shop, I think 5000k is probably a good choice, although some folks really enjoy the crispness of a 6500k light. But you should test them out for yourself to see what you prefer.
If you’re starting a small business for the first time, your new best friends in life should be your bookkeeper and your accountant. The former should be engaged for a few hours every week (especially at the start of your business) to compile your books and ensure your records are maintained to the required standard, while the latter will help review your tax situation and prepare financial statements. Both can also be used as invaluable sources of actionable intelligence about ways to reduce costs, increase margins, and generally streamline your finances.You’ll be able to spend all that time you save doing what you love and thinking strategically about your business.
Whether you plan to go it alone or hire a professional, there are many resources available to help you plan and execute your retail store layout. If you don’t feel comfortable tackling the project yourself, a professional retail store planner, interior designer, or display designer can turn your dreams into reality. Or if you want to handle it all yourself, store planning software and other online idea resources can make the job easier.
Like most things in life, we believe that entrepreneurship can be learned, you just have to be willing to put one foot in front of the other. Aftering reading How to Start a Small Business 101, you’ll be equipped with the essential tools and resources you need to succeed at planning, raising capital, and executing crucial day-to-day business operations.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Note: This article will not include considerations for costs by independent developers or offshore firms. As I have written about cost differences in previous articles, those costs vary widely. Instead, this app cost resource focuses on what it would take to have a quality team of professionals build different kinds of apps. That could be done in-house, by building your own team, or by contracting a third party agency like Savvy Apps.
But now is the time to take a step back and go on some test runs in your van. Take it out for a weekend here or there (or better yet, a week or more). Try living in it as you expect to on the road. We guarantee there will be things that worked well in your head but not so much in reality. And you’ll come up with random little hacks and innovations that will make your life on the road easier and more enjoyable.

If you have a broker that’s too successful you may be a low priority. If you choose a broker that’s inexperienced but attentive, you may end up paying for their novice mistakes. My advice is to not choose a broker but instead choose a team. Pick a junior/senior combo so that when you’re hunting for space you work more with the junior, and when it comes to negotiating the deal you have the experienced veteran leading the negotiation.”
For small business owners starting or wanting to grow a small business, attracting and retaining customers is a huge priority. Let’s face it, without customers you don’t have a business to run. Over the last decade there has been an explosion in the number of high-quality, affordable technologies that are specifically geared towards helping small, local business owners improve the day-to-day operations that impact this aspect of their business. This includes point of sale systems, tax software, bookkeeping software, employee scheduling and payroll programs, inventory tracking tools, customer loyalty programs, gift card technology, ecommerce opportunities, website builders, email marketing software, and social media management tools. The list goes on and on.

Hospitality expert, Chip Conley founded and grew the Joie De Vivre hotels from a single San Francisco location to become California’s largest boutique hotel management company. How? He understood the value of a unique vision when it’s consistently applied. He created each hotel to reflect the spirit of a niche-oriented magazine that he felt represented his target market. Examples include the Phoenix (Rolling Stone), the Rex (The New Yorker), Hotel Avante (Wired), Wild Palms Hotel (Fast Company), Hotel Los Gatos (Town and Country), and the Water's Edge (Yachting). Obviously your inspiration doesn’t need to be a magazine, it can just as easily be a song, a group of words, or just a particular image. Find something that resonates with the customers you have in mind and design your store to reflect that vision.
He’s also providing power to a cool light grid we’re building from several old fluorescent fixtures that we salvaged from past remodeling jobs. With six four-tube fixtures, we should get plenty of light. In a work space you want to install these lights high enough so they don’t get in your way when you’re moving materials but low enough to provide good even light.
Just stumbled across your article and it’s right on time as I am about to launch a special events venue (ballrooms, meeting rooms, outside garden area, outsourced caterer, etc). Not sure what type of zoning this business falls under. I read that zones are usually for office, retail, industrial and leisure. Any idea what type of zone I should be looking for? Also first time trying to get a commercial space for this type of business, any specific suggestions?

Now, photographs or video tape will also be very useful especially to pass along to your insurance adjustor. Now the problem is this documentation won’t help you at all if it’s lost or destroyed so consider saving your information electronically. Take your photos with a digital camera and create a list of all your valuables, and save both in a computer file. This file can be saved to a disk you can keep at work or upload it to a website that you can access it from anywhere including your home.
If you dream of devoting your life to a cause you believe in, it might be time to start a nonprofit. You’ll need to incorporate your business and file for 501(c)(3) tax-exempt status -- and then you’ll be required to meet ongoing standards of compliance, but the payoff is making a meaningful impact on a cause you believe in. Want to do good while still making a profit? Consider social entrepreneurship.
Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Small business owners can maintain steady, manageable growth by keeping a firm eye on costs and always aggressively looking for ways to increase sales and grow their brand. It can be difficult to empower staff and managers around you, especially if you’ve spent a long time steering the ship alone, but it is an essential part of successful expansion. Stay open to suggestions from your managers while making your current business best practices clear to them.
I would definitely stick with the vapor barrier under the floor to avoid moisture from breaking up the OSB. try to build the base high enough to keep it dry and allow airflow to dry it out under there. FYI I recently repaired a neighbor's shed roof that must have been partially repaired before with plywood. The OSB was fine under the shingles, but the plywood was wrecked due to moisture. I would stick with OSB. Since you live here in NOVA, details will be a little more helpful to you. I really can't use the shed in the summer without the AC on. It gets direct sun and gets up to the 90's in there with out any air movement. I am planning on eventually lining the inside of the ceiling with that thin reflective insulation to bounce back some of the heat.
Another flexible option is the portable work tables the guys are building back in our shop. This gives us a work surface that we can move wherever we may need it. Now the main workbench we’ve left a little gap between two of the cabinets for a trashcan or a stool to slip in but we did need to support the countertop where it crosses so Tim and Chris are adding some 1x4s to bridge the space. They’re also putting in a 2×4 inside one of the cabinets where the two pieces of plywood will have to be seamed. Then it’s just a matter of laying in the pieces in place and nailing them down to the cabinet. That trim strip around the edge is mostly for looks but the cedar backsplash along the back will keep us from banging up the wall or getting small items stuck between it and the counter. All in all it started to look pretty good.

Most people know they should document their homes contents for insurance reasons but they often ask why or how to do it the right way. If you have a loss due to fire, theft or a natural disaster your insurance company will need certain details to complete the claims process, including a description of the item, the model number, the serial number the date purchased the color and the purchase price.
Before you buy a single tool, you need to take a hard look at your workshop space. If your workshop is a freestanding building or empty barn, you can simply measure the perimeter and know that you have the entire square footage at your disposal including the wall space. If your workshop is tucked into the back of a garage or a corner of partially finished basement, you’ll need to plan your furnishings with cars and water heaters in mind.
While an electric miter saw is a convenience, it is not necessary to do good work.  A quality electric miter saw will run around $150-$200, that by itself would destroy our budget.  A hand saw with a miter box does the job just as well at a fraction of the price.  This highly rated Stanley version for ~$60 should get the job done, albeit with a bit more elbow grease.
There are benefits to either approach. Sharing a common wall with your house can require some careful soundproofing but can reduce heat loss and exterior fin­ishing costs like siding. A shop located in an addition is more likely to be allowed to have living space or storage space above it, and it may be easier to make use of the existing plumbing and electri­cal and heating systems of your home to service your shop space. Another advantage of an addition is not having to run to an outbuilding in minus-30-degree weather or a summer downpour.
While an electric miter saw is a convenience, it is not necessary to do good work.  A quality electric miter saw will run around $150-$200, that by itself would destroy our budget.  A hand saw with a miter box does the job just as well at a fraction of the price.  This highly rated Stanley version for ~$60 should get the job done, albeit with a bit more elbow grease.
If you want the ultimate vehicle to customize for your DIY van conversion, the Sprinter is the van for you. They have enough headroom even for tall people to stand up, and enough interior space to design any kind of layout. They also typically have diesel engines, which means greater fuel efficiency and engine life (many diesel Sprinters have been known to make it past 400,000 miles). If you think you’ll be doing a lot of off-roading, the Mercedes Sprinter also comes in a 4x4 version.
In our opinion, the best kind of fridge you can get for a DIY campervan is a portable 12V fridge/freezer. These fridges are built for adventuring on 4x4 vehicles and boats. They’re very rugged, and they don’t need to be kept perfectly level like mini-fridges. They can run off 12V power or regular 110V. They keep your food as cold as you want, and they can operate as either a fridge or a freezer.
Hey Joe, I just hit 178k on my truck. I remember when I started out the first time around it had like 144k or so. They are known to go quite far, so we’ll see how it goes. Maintenance on the road… I just stop at those oil lube places for the most part, and do regular weekly checks under the hood for fluid levels, etc. I’m not too mechanically inclined!
Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regula­tions, a larger lot, or more congenial neighbours. 
Another flexible option is the portable work tables the guys are building back in our shop. This gives us a work surface that we can move wherever we may need it. Now the main workbench we’ve left a little gap between two of the cabinets for a trashcan or a stool to slip in but we did need to support the countertop where it crosses so Tim and Chris are adding some 1x4s to bridge the space. They’re also putting in a 2×4 inside one of the cabinets where the two pieces of plywood will have to be seamed. Then it’s just a matter of laying in the pieces in place and nailing them down to the cabinet. That trim strip around the edge is mostly for looks but the cedar backsplash along the back will keep us from banging up the wall or getting small items stuck between it and the counter. All in all it started to look pretty good.
When I’m working on projects in the shop, I often have my laptop close by so I can refer to an article or take notes. The craft table I’d been using was too low, so I got some pieces of 1-1/4-in. PVC pipe to slip over the legs. I measured the height so it was just right—no more aching back! The pipe pieces are easy to slip off when we need the table for potluck. — Donna M. Courie
By setting up a separate legal entity, you limit the financial fallout from a failed business, you shield yourself from legal risks (such as someone injuring themselves in your store), and you potentially put yourself in a more advantageous tax situation. Equally, if you are working with partners, ensuring you are set up with the appropriate partnership will give all parties reassurance about their legal standing, obligations to, and expectations from the business in question.
We have a 5-gallon clear plastic Hedpak container that our sink drains straight down into. We really like this container because it’s clear, which means we can easily see how full it is. With 5 gallons of gray water capacity, we only need to empty it every 3-4 days. Dumping is easy - just remove the tank from under the sink and pour it out into an RV dump facility or other approved area.
×