In a small store, these are usually one and the same. In stores where customers don’t shop with baskets, Lesley recommends having a checkout counter large enough to hold products as customers continue shopping. Remember, empty hands pick up more products, and that leads to more sales. Also, make sure checkout counters are large enough to handle the checkout process efficiently and allow space for customers to set down a handbag.
Just a quick note about light spectrum. I went with 6500k because that’s what I like to film in. The daylight spectrum makes it easier for me if I decide to open the blinds, letting in some natural light. For the average woodworking shop, I think 5000k is probably a good choice, although some folks really enjoy the crispness of a 6500k light. But you should test them out for yourself to see what you prefer.
You might be thinking your business aspirations are too ‘early-stage’ to merit investigating the permits required to run your small business. You’d be wrong. The costs and requirements of staying on the right side of the law should be factored into your initial business plan and ongoing projections. In the long run, this will save you time, money and heartache.
We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.
Many small business owners start on a shoestring budget, intertwining their personal and business finances, supporting the business with their personal credit cards, accepting payments into their personal checking account, and even submitting tax returns that mix up personal and business finances. While this is common, it can create tax headaches, make bookkeeping more time consuming, and, most importantly, can also interfere with the proper evaluation of your business.
Hey thanks for the great insight on a pickup camping setup! I just purchased a 2002 tundra with a 74″ bed. Picking it up in Denver in a week and driving it to Durango and then around the southwest. I mainly decided on a truck for a mobile place to keep my dog(that doesn’t have an interior he can rip to shreds), but I am thinking of building a setup similar to yours. You haven’t used yours with a canine companion have you? Any suggestions on keeping it dog-friendly, dog-comfortable and dog-proof? I will be keeping him in the back while at work and such and will be camping in the back with him and possibly another person.
Expanded polystyrene (EPS) is an open-celled foam board (think styrofoam) that is the cheapest of all the foam boards. It does work, but we generally don’t recommend using EPS in your van. It insulates less than XPS (R-4 per inch), and the gaps between the foam cells allow moisture to penetrate, which degrades the insulation over time. Polyiso and XPS are much better choices for a slightly higher cost.
Smaller speed bump displays (above) and larger merchandise outposts (below) placed along your store’s main traffic flow let you draw customer interest to certain products. Speed bumps let you feature new finds and hot sellers in eye-catching ways. Larger outposts are great for special price stock or product groupings such as seasonal features and branded collections.
The big advantage to buying a pre-built camper is that it’s already built out, so you won’t have to wait to hit the road. Many feature innovative ways to convert the living space into a sleeping area, and may even include a bathroom/shower. These vehicles should also have electrical, plumbing, propane, and water systems already installed (although if you want solar power, you’ll likely need to add this yourself).

I wanted to have numerous outlets, and have enough elec­trical service that I did not have to worry about overloading circuits. There was already some lighting, so I simply picked off that line and added additional lights to keep things bright and cozy. I ran a 240V line for the table saw and jointer with a dedicated breaker. For wall outlets, I ran 14-3 wire, and split all the plugs, so that I can run one machine on the upper plug, and another on the lower plug of any outlet.

Ideas on how to Improve your Workspace – We can all do with some ideas on optimizing workspace. The guide has a lot of information about how to improve your workshop to be more efficient and improve workflow. This includes the costs of improving your shop, as well as hacks you can do yourself to improve efficiency and storage space for less. You’d be amazed at what you can do with even a small room. You just need someone to point you in the right direction.
I decided to do Optimus for many reasons. One big one was that no one else in the world had done it. There are tons of Bumblebee Camaros and other replica cars, but no other fan of Transformers has replicated the T4 (fourth Transformers movie) and T5 (fifth Transformers movie) Optimus trucks. So if I am to show my son through action what it means not to be afraid to take a chance, I figured Optimus was the best way to try.
The tablesaw—This tool is the backbone of nearly every shop, and for good reason. It allows unmatched precision in ripping parallel edges and crosscutting at a variety of angles. Most woodworkers find it crucial for the basic milling of stock. It is also suited to many joinery tasks, easily producing tenons, box joints, and—with a reground blade—the tails for dovetail joints.

From building websites for other small businesses to providing technical support for certain projects, quality web development is in high demand right now. With such a technical skillset, make sure you can describe what you do and how you will do it in easy-to-understand language. Test your messaging on friends and family who don’t have a firm understanding of the work you do.

It’s important that you have a fundamental understanding of what is making your business successful before you decide to expand. Who are your customers and why do they enjoy what you offer? Who are your suppliers and will they be able to deliver to your new location? What are your operating costs and will they be the same in a new location? A lot of small businesses start off in the suburbs of a town before making the move to a city’s business district, only to find that unexpected additional costs are swallowing up their profits.
It is also essential to take a lean, data-led approach to choosing a business space. The average length of a commercial lease has dropped over the last few years but is still often well over five years, so the absolute last thing you want to do is rush into a signing and get locked into a bad situation. There are so many ways to test the viability of your business idea before you over-invest and sign a full-blown lease agreement.

I framed in a 4x8 Garden Shed on the back.  I didn't want it so deep that stuff would get buried in it.  I need to take an updated picture of the back.  These pics were from early on and I have changed some things in the organization.  I used similar framing techniques and built a lean to roof attached with metal hangers.  I chose to use clear corrugated roofing to allow natural light into this shed.  You can see the 2 shopvacs that were originally part of my simple vacuum system.  I have removed them and found that I get better airflow using an electric leaf blower with the vacuum attachment hooked up to my system.  There is a large metal trashcan with a dust collection separator to collect the larger pieces of saw dust and chips.  My air compressor is on a shelf on the right now and I ran a hose through the wall and to a 25 foot reel attached to the ceiling.  I wired separate switched for both on the inside of my shop.  These systems work extremely well for a small shop.  The wall provides some insulation from the overwhelming noise they would otherwise create inside the shop.

Hey, you ever wonder what it look like behind the scenes at a home improvement show? Well here’s a little glimpse of it. This is a storage building I’ve had for awhile and we use this for storage and materials and props we use on the show and it’s also used by my construction company. Well this part of the building has kind of turned into a little bit of a dumping zone, where people just dump things that they’re not sure exactly where they go in the rest of the building.
This site uses affiliate links. Given this, please assume that any links leading you to products or services are affiliate links that we will receive compensation from. However, there are millions of products and services on the web, and I only promote those products or services that I would use personally. The Wood Whisperer abides by word of mouth marketing standards and holds integrity in the highest regard. Should I ever be compensated to write, I will make full disclosure. I always give honest opinions, findings, and experiences on products. The views and opinions expressed on this blog are purely our own. Any product claim, statistic, quote or other representation about a product or service should be verified with the manufacturer, provider or party in question. All content on The Wood Whisperer is copyrighted, and may not be reprinted in full form without my written consent.

That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.


Apps begin to get more complex—and costly—once user authentication is involved. The main reasons for that are all the other expectations that come with user authentication. Typically, they include interacting with data (e.g., favoriting an article), syncing data across devices, push notifications, and perhaps collaborative features (e.g., inviting a family member).
To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.
When leasing a retail space, there is always risks involved. Your goal should be to minimize these as much as possible by considering every angle and asking the right questions. For example, does the landlord intend on erecting scaffolding on the building at any point during the lease? If so, can the rent be reduced to reflect this situation? You will also want to ask to have a clause included allowing you to sublet if necessary, which can be important if you ever find yourself struggling to make payments.
​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.

It’s also a good idea to cover up any exposed insulation or open stud bays so that you have a flat surface to mount stuff on the walls of your workshop. Here we’re attaching plywood panels to the metal framing but in most garages or sheds you can just nail them directly to the studs. We’re also getting a jump on organizing by putting in a hose reel next to the location we’ve chosen for our air compressor.


This holds a lot of stuff but mainly our handheld power tools, so it needs to support a lot of weight. Any shelf in a workshop will probably wind up supporting more than you initially planned so build it as strong as you can and don’t scrimp on the materials or the fasteners you use to hang it. Now the next step is to install our recycled cabinets that will line the wall under the shelf. Now these cabinets are a little plain but that should work great for a shop like this. Even if you don’t own a remodeling company you can usually find these things pretty inexpensively from salvaged warehouses which recover them from renovation projects then resell them to the public.
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.
The thickness planer—A thickness planer will significantly expand the creativity and craftsmanship of your work by allowing you to buy roughsawn stock and use wood of any thickness in your designs. Nowadays, a new planer often represents a better value than a used model. In recent years, DeWalt and Ridgid have introduced portable planers with chip-ejection fans, which work as a built-in dust collector. Dust collection is important for all tools, but essential for thickness planers. This feature can help delay the expense of a dust collector and thus reduce the overall cost of a planer. Speaking of dust collection, I should mention that I don’t use a dedicated dust collector in my shop. I use a shop vac with a small hose for my sanders and a larger-diameter hose for the tablesaw and router table, and I depend on the built-in chipejection fan for my thickness planer.
Now, this is kind of an odd situation here, a few years ago when we bought this building there was a concrete block wall around here and a large drain right in the middle of the floor. Well the drain will certainly come in handy for any cleanup in the shop but the walls kind of left us when we removed those kind of left us a little divot and a little bit of damage here, so to make this nice and smooth so that our rolling workbenches will roll around real nicely we’re having to do a good bit of floor patch.
As a carpenter, I need to bring certain items with me every day. I bought a cheap plastic tote in the tool storage area at a home center and modified it for my needs. I made a small plywood deck, drilled a couple of 3-in. holes for coffee cups or glue bottles and then fastened it to the tote. Another piece of plywood has holes to keep pencils upright and organized. My tote sits nicely on my bench seat, but it could also be attached to the floor with hook-and-loop fasteners. You could easily customize these totes for plumbing, garden or painting tools, electrical supplies—what have you. — Don Simms. Check out this jumbo tote for fasteners.
Love the design. I’ve got a 15 tacoma, which has rails that run the length of the bed and are what my shell is “clamped” into via a bed rail nut. Hence my problem with following your outline verbatim. Any suggestions for incorporating the rail as a substitute for the 2×4 you clamped into your truck? Essentially connecting the 3, 2×4 braces directly to the rail… I’m a construction novice, any suggestions greatly appreciated!
Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.
Do you carry items that bring your customers back time and time again? Consider placing these primary and similar secondary product lines toward the back of your store. Or, if your stock is constantly changing and you don’t carry replenishing goods, place your sale items toward the back. That way, customers must pass your new items and promotional displays on their way to check out the deals in back.
It's true for large and small shops alike: Sawdust and chips get everywhere when you use power tools. Small home-woodworking shops are often in shared rooms and may be poorly ventilated. And airborne sawdust and particulates linger for a while before settling. It's a bad combination for human lungs, which are not fond of sawdust, let alone the types of chemicals found in plywood and other engineered materials.
A software engineer needs to know how to code.  An administrative assistant must answer phones and organize paperwork.  But a marketer typically needs to wear many hats, from writer to advertiser to strategist.  And unlike other job roles, marketing employees can affect the core of a business by changing the way it’s positioned — and they can be held accountable to the company’s bottom line.
The nomadic truck camping lifestyle has been incredibly freeing, not only is cheap and accessible to most anyone, but it can take you beyond places you even imagined. One book that I’d recommend to all newcomers to this lifestyle is Bob Wells’ How to Live in a Car, Van, or RV, which will help you better understand the ins and outs of this lifestyle.
Great instructional! I built the bed of my 92′ Toyota pickup ext. cab the same way you did. I did some hard searching and found this camp pad, which literally fits the 40″ wide sleeping space perfectly. A few different mats from Exped will fit, but here’s the one I bought. Just thought you might like to know there’s an inflatable duo sleeping pad out there that works for your setup!
I have to agree with these folks....I have a two car garage/workshop that needs to double for ski waxing, bicycle storage and house repairs. I have a Hybrid Table saw, 6" jointer, 13" planer, a shopsmith that serves as drill press, lathe and band saw, dust collector, two work benches...and everything has been designed to roll away, under, above something else...I can set up and tear down in about ten minutes, because at the end of the day, I always have to park two cars in the garage. Always great to look at the great dream workshops, but thought that they should do an article on guys like us, that have to fit several hobbies into one spot. I seem to spend a lot of time planning, and re planning the garage space to try and fit the next tool. I dream about the day I will get a place that I can dedicate to my tools, but until then, I just buy things with wheels.
When leasing a retail space, there is always risks involved. Your goal should be to minimize these as much as possible by considering every angle and asking the right questions. For example, does the landlord intend on erecting scaffolding on the building at any point during the lease? If so, can the rent be reduced to reflect this situation? You will also want to ask to have a clause included allowing you to sublet if necessary, which can be important if you ever find yourself struggling to make payments.
Hello! My name is Donna Jean. I love to read books and my job is to write a daily review of all the novelties in the world of eBooks. I allow only the best of them to be published on my website. I really hope to make our world more bright, beautiful and kind. You can participate by downloading any book from my site, and you will receive health, luck, kindness, and love, which will support you during all your life. Wishing your dreams begin to come true, and every tomorrow be happy for you. Thank you! ❤❤❤
×