As part of my antique restoration work I do a lot of faux finishing – hence the supply of stains and paints. Since I didn’t want to dust the house, the new shop is not connected to the house heat and air system. But, having just finished our first winter I now know the shop didn’t get below 45 degrees – and, the oven in the corner can make the shop toasty in no time at all.


A great supplier will provide the raw ingredients of your success — often literally. What’s more, they’ll deliver them on time, every time. And they’ll always deliver exactly what you ordered, no more, and no less. A large part of the process of inventory control is ensuring that you are paying for exactly the inventory that comes through your door, and not a penny more. Even great suppliers, however, are looking for the highest price possible for their goods, so once you find them, make sure you’re ready to negotiate!
I’m for using what you have got as well but if what you’ve got just really isn’t up to the job it doesn’t hurt to consider switching to something else. Not sure what year your Prius is but if it is fairly new I imagine you could sell it for much more than what an older reliable 4 cylinder Tacoma would cost you. My 2wd Tacoma manual trans gets 30mpg pretty easily and I’m never tempted to get a hotel. The price difference in the two vehicles alone may well make up for the extra cost in fuel and potentially tempting lodging plus even in a 2wd pickup you will have a much easier time going off the beaten path then you will in a low hanging passenger car.
We don't have a Dometic CFX-50 in our van, but we wish we had gotten one for our build. This is a great little fridge that many vanlifers happily own. It’s rugged and durable, and it keeps your food cold for less money than many of the other fridges out there. It also has a nifty side-open lid, which makes it a lot easier to open with a lower clearance.
These basics are going to set you back about $180, leaving you with $320 left to work with.  We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives.  This should lead to more consistent results, more enjoyable builds, and increased efficiency.  These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
For many new small business owners, the additional expense and bureaucratic hoopla involved in obtaining the correct paperwork often leaves them dragging their heels. This attitude, however, can result in stiff financial penalties, or worse, having your permission to do business revoked. Before we jump into the why and how of obtaining your business permit or license, it’s important for you to understand the difference.

To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.


A table saw is one of the most important tools in the workshop for its ability to make long straight cuts. It will also cross cut with ease and if you don’t want to cut clean through a board you can adjust the height of the blade to make a dado or rabbet. A handy feature with the BTS10ST table saw is the vertical stand which also saves on storage space.
At some point in the process of starting a small business, it’s pretty much guaranteed that you will hear the following statistics (or variations thereof): 25% of new small businesses close their doors within the first year and 60% are gone within three years. The exact numbers here may vary, but the message is all the same: be afraid, be very afraid!

Gutting: We actually took on a pretty big project when we bought our van because it came with a preinstalled wheelchair lift that we had to remove. Unbolting all the parts took both of us working on it for a full day, and it wasn't the most glamorous job. The good part was that we were able to sell the lift and the reclining bench seat for a combined total of $260. If there's anything to remove from your van, do this first.
We did our best to keep costs down, but there was only so much we could do. We needed the shop to go up quickly, which eliminated the prospect of me doing some of the work myself. Additionally, we live in a neighborhood with a homeowner’s association. This means we have very specific restrictions for what we can and can’t do on our property. So the shop must have all of the same finishing touches as our house.
So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.
Without organization, living in a van can feel cluttered and chaotic, so you'll want to make the most of your storage space. This is a good time to make sure you've paired down your belongings to a reasonable amount and to make sure everything has a place. (As a former engineer who loves making things as efficient and optimized as possible, this was Ben's favorite step!) 

The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code con­ventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow founda­tion may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the con­crete slab will structurally bear the weight of the shop structure you build above it.

I do not rip on the table saw as a rule, to prevent kick back that periodically occurs when natural wood pinches the blade, turning the wood into a missile. I bought a fairly powerful saw, so this is one place where a lighter saw would be adequate. Essentially, I use the table saw for ripping sheet goods, cutting dados, tenons, and cutting small parts to length – all of which can be done with a 1.5 HP saw. I ended up with a King 3 HP, three-belt drive, 10" table saw. The castings are true, and the King Tru-rip fence reminds me of the Biesmeyer fence used on the Canadian General saws. The model is KC-11FX, and it can be purchased for less than half of the price of other, simi­lar saws. On this purchase, I went with the suggestion of Jeff at Brettwood Machinery – he was right; a very good value saw that runs smooth, and has a decent fence.

At some point in the process of starting a small business, it’s pretty much guaranteed that you will hear the following statistics (or variations thereof): 25% of new small businesses close their doors within the first year and 60% are gone within three years. The exact numbers here may vary, but the message is all the same: be afraid, be very afraid!
A great freestanding beverage cooler should come equipped with a thermostat that lets you control the temperature to your liking — the colder the better for carbonated drinks, which tend to taste best when served at a frosty 34 degrees. If you plan to store adult beverages in your cooler, look for a model with a lock to keep your drinks away from children and teens. You’ll also want a model that allows you to reverse the way the door swings when you set it up, as this will provide flexibility in your workshop layout to help maximize your space.
Now, we’ve already applied some resurfacer to fill up some of the deeper holes and after that dries overnight we’ll use a floor leveling compound tomorrow morning to really smooth everything out. Leveling compound is more fluid than the resurfacer so it flows into all of the low spots to even out the surface. Now, this won’t look like a finished floor when Tim’s done but it should do the job for our shop. Now, while he wraps up this Emily has a Best New Product that might be a great addition to your workshop.
Well I’ve been kind of fighting that, because I wanted to keep it open to where you could have the flexibility of moving things in and out. It probably makes sense. Actually have another old set of cabinets I thought about putting here, maybe put some really good casters on it to where you could keep it here. I’m also, wanted to be able to store like drum sander, other things that can go under it and then you can take those out and put them on this.
Without organization, living in a van can feel cluttered and chaotic, so you'll want to make the most of your storage space. This is a good time to make sure you've paired down your belongings to a reasonable amount and to make sure everything has a place. (As a former engineer who loves making things as efficient and optimized as possible, this was Ben's favorite step!) 
So what does all this boil down to? I favour starting with a good workbench and top quality hand tools – chisels, a couple of planes, a hammer, a few Japanese handsaws – stuff like that. You’ll be amazed at what you can accomplish when properly equipped. Build simple items at first, and then add the very best power tools you can – as you can afford to – in the order that makes the most sense for the work you’re interested in. Yes, this gets you off to a slower start, but what’s the rush? You’ll soon surpass the ‘buy-it-all-at-once’ folks who end up struggling with beginner tools that hold them back from getting better.
Remember, your retail store layout guides product placement, directs customer flow, and defines the overall look and feel of your store, so it deserves plenty of thought. Many factors will affect your floor plan choice, including the size and shape of your sales floor, the types of products you sell, and even the customers you hope to attract. Keep these factors in mind as we explore each floor plan option in detail.

You can also make your store comfortable by incorporating a waiting area with comfy seats and benches to encourage customers to spend more time in your store. This is especially helpful for shoppers accompanied by someone who isn't interested in making a purchase. But keep the seats or benches facing the merchandise so that they're still top of mind for those lounging around in your store.  
Firstly, more and more consumers are rebelling against the generic offerings of big-box retailers and seeking out the unique, personal touch offered by small, local business. You can leverage this message by weaving yourself into the fabric of your community. Canadian yoga apparel retailer Lululemon has enjoyed explosive growth thanks to their ability to do just this. According to their website, “A Lululemon store is so much more than a place to shop. It’s an education centre, a yoga studio and a meeting place. It’s a local hub for educators, ambassadors and guests to gather to learn, sweat and connect. It’s our lifeline to our communities and the soul of our company.” Lululemon uses free events to make people feel that they have a sense of ownership over the brand, and you can too! Getting people through your door is 90% of the battle and event marketing definitely can bring in crowds.

Concrete garage floors can work as a workshop surface, but over time they stain and you’ll end up tracking a lot of dust and dirt into your home. An epoxy floor finish is easier to clean and can also provide extra grip. For a softer surface that will help your joints when standing a long time, check out those restaurant grade rubber floor mats or some durable options that include garage floor tile.
I bought an energy-saving outlet strip for my TV and its components. One outlet controls several other outlets on the strip, so when I turn off my TV, the adjacent controlled outlets for my VCR, DVD player and receiver sense that no current is going to the TV anymore, and those outlets shut off. Then I decided to try it out in the shop. I use it with my router table, disc sander and orbital sanders, so when I flip one of them on, my shop vacuum also starts up to take care of dust collection. It also has two outlets that are independent for other accessories you’d like on all the time. You can buy the outlet strips at amazon.com. One choice is the Belkin Conserve Socket with Energy Saving Outlet (about $30). — D. Linley. Plus: 30 more smart tips for working in your home shop.
Once you have your space secured, hang some pictures in the windows that illustrate what’s to come. It’s also a good idea to provide leaflets that people can take away with them and hang a clipboard and pen on the front door where people can sign up to hear more about your business. This list is pure gold! So once you have it, why not stage a launch party and invite the local community (and local journalists). The first step for any business is always getting people to try out your products!
State Parks/Developed Campgrounds. Every once in awhile, it’s kind of nice to stay at a state park or other developed campground - and a big reason why is that they have showers (and sometimes laundry, too). This is what we’ve done most often when we need a shower on the road. Many state parks also have small day use fees if you don’t want to actually camp there.
Time spent earnestly involved in the creation of something designed and made with one’s own ingenuity can be quite enjoyable. So now when I don’t feel motivated to do more practical things I often turn to an idea about some device or other that I’ve wanted to try making but never got around to. Ultimate Small Shop Videos I can recall many such improvised devices that gave me satisfaction and enjoyment.Ideas for things to make come from many places. Most often the idea comes from some need. I do a lot of keying of text using a computer keyboard. I tend to keep the room temperature a bit cool, cool enough that my hands become uncomfortable. I ended up rigging a length of electrical heating tape wound in a large coil-shape to surround the keyboard. Tying the heat tape to a large piece of cardboard keeps it in place. It does a nice job of keeping my hands warm. I can leave the room temperature set where I want it. As far as I know, you can’t buy anything like that. Building and inventing improve my understanding of mechanical devices and materials. It gets easier to manipulate and modify the physical things that are so much a part of everyday living. With effort and imagination, often new devices can be made or existing ones improved for my enjoyment and satisfaction. Both intuition and logic are used to make a homemade gizmo. The more the two abilities are used together, the more powerful the combination becomes. A strong partnership of reason and creativity helps a person to produce and enjoy life. It is fun and satisfying to conjure up and build simple devices. Those created items command more appreciation than more casually acquired, purchased items. And it feels good proving that imagination and ingenuity can make life better. The process of invention seems magical. The mind pieces together what it has already made some sense of into something new. It seems that even the most obscure result can eventually be produced. The grass hut and the keyboard heater each gave me a little taste of that magic. Until recently crafts were usually sold locally or, at best, regionally. Now you literally have the whole world at your fingertips! Some of you may choose a gradual progression from selling to friends to selling at fairs and shows, to retail selling … and so on. Others may decide to jump directly from selling within their circle of friends to the worldwide Internet market – the costs are low enough that this is surprisingly doable. My first career was as a special education teacher. After 15 years of teaching, I earned an MBA degree followed by CFA (Certified Financial Analyst) certification. Ultimate Small Shop Pdf Download After 15 years in finance I was a vice-president and portfolio manager of a major insurance company before I was downsized.
However, there are some downsides. If you want to customize the interior you’ll have to completely gut the entire thing, which can be a lot of extra work. The weird shape and fiberglass construction of most high tops also make it more difficult to install solar panels, a ceiling, or anything else on the roof. And we’ve also found that some auto repair shops aren’t tall enough to put our van up on a lift - though that’s only really an issue for major work, not routine maintenance.
The ARB fridge 50-Qt Fridge is the best of the best. ARB is an Australian 4x4 accessories company, and all of their products are built to withstand just about anything. The ARB fridge is extremely rugged, and features powder-coated zinc steel construction for the ultimate in durability. It can take a beating, and works just fine on inclines up to 30°.
Tired of holding a flashlight between your teeth while working in the dark? Make a light stand by bending a 2-ft. section of 12- or 14-gauge electrical cable into a U shape. Duct-tape the light to the ends of the cable. The wire can be shaped into a hands-free supporting base for the flashlight or bent into a hook for hanging. — Paul and Haylee Lytle. Check out another hands-free light hack.
When I change blades on my band saw, I usually need to adjust the thrust bearings and guides with an Allen wrench. I was tired of hunting around for the wrench, so I decided to stick it to the steel housing with a rare earth magnet (neodymium) about the size of a jacket button. Now it’s always handy! — Bill Wells. You can also use a magnet on your ladder.
Ryan, I have the same (almost) 90’s Toyota Pickup and love it! this is so helpful, and I will definitely be using this method. my main concern is that 1/2′ plywood sagging. do you notice it sags quite a bit or does it mostly hold up? my thought was to build the vertical bins a little wider, so that the plywood bed platform wouldn’t be under so much stress. the second issue im running into is wrapping my head around trying to organize and compartmentalize things appropriately. what do you typically put where so it is easy to reach and use?

A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.

Tired of holding a flashlight between your teeth while working in the dark? Make a light stand by bending a 2-ft. section of 12- or 14-gauge electrical cable into a U shape. Duct-tape the light to the ends of the cable. The wire can be shaped into a hands-free supporting base for the flashlight or bent into a hook for hanging. — Paul and Haylee Lytle. Check out another hands-free light hack.
If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.

While we were painting all of the walls in our workshop our plumber dropped by to hook up an old laundry tub sink that we’ve had for several years. Now, he hooked up to the cold water line on an outside water faucet, so we’ll only have cold water but still this will be really convenient to have this right here in this shop. Well we’re about to set our last base cabinet, and once they secure that well to the wall we can start on all of our countertops.


This is the one tool in the shop that provides the greatest opportunity to save money, if you are willing to purchase a well made, light duty machine, and take lighter cuts. In the past I have used General 14" planers that can hog off seri­ous cuts all day long. The problem is that these professional units cost over $5000, and they would crush my buddy as we haul them down the stairs (note: don’t be the guy on the bot­tom). After doing a fair amount of research, I purchased the Dewalt DW735 13" thick­ness planer. The unit came with a good manual, and was in a good state of tune. It is light enough for me to carry around the shop with­out excessive grunting, so that made it very simple to install. The planer has a sig­nificant internal fan-assisted chip ejection system. The chips are catapulted out of this planer, so have your dust collector running before you run stock through it. I now have to make more cuts at a lighter cut depth, but I saved about $4500, which makes my budget happy. The planer makes clean cuts, and has two speeds. I don’t see a reason for the two speeds for my type of work, but there is a faster feed rate should you choose to use it. Knife changing is simple and quick.


When starting your small business, the easiest way to go about choosing a business name is to approach the task the same way you approach building new relationships. Did we lose you for a second? Here’s what we mean. It takes just one-tenth of a second for us to judge someone based on a first impression. There are endless relationships that instantly blossom or never get off the ground based off of this one simple fact. Most of us, even if it is on a subconscious level, understand this. Which is why when we meet someone that we are trying to impress, we make an attempt to adjust our appearance, body language, even the way we talk, to ensure we are putting our best foot forward.

For example, at a certain point, you will be asked to project how much cash you’ll spend in your fifth year of business. You’ll think, “Are you kidding? I haven’t even opened my doors yet and you want me to describe what my expenses and revenue will be like in five years?” Well, the quick answer is yes. Nobody ever said that starting a small business would be an easy feat.
“We believe that we are on the face of the earth to make great products and that’s not changing. We are constantly focusing on innovating. We believe in the simple not the complex. We believe that we need to own and control the primary technologies behind the products that we make, and participate only in markets where we can make a significant contribution. We believe in saying no to thousands of projects, so that we can really focus on the few that are truly important and meaningful to us. We believe in deep collaboration and cross-pollination of our groups, which allow us to innovate in a way that others cannot. And frankly, we don’t settle for anything less than excellence in every group in the company, and we have the self- honesty to admit when we’re wrong and the courage to change. And I think regardless of who is in what job those values are so embedded in this company that Apple will do extremely well.”
At $300, the saw is expensive, but it is one of the more affordable saws that offer a 12 inch blade and a double bevel.  The double bevel allows you to adjust both the angle at which the blade cuts into the wood and the tilt of the blade relative to the workpiece.  Having control over both angles allows much easier cuts of trims and moldings.  It's one of those features that you won't use with every project - but when you do need it, you'll be glad you have it
Tip: Save money on specialty displays! Many manufacturers offer retailers low-cost or free specialty display fixtures designed to highlight their branded lines, like the one pictured below. These make great speed bump or outpost display units on a tight budget. Your product line reps can tell you if they’re available, plus provide merchandising and display advice.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
One of the core skills needed when starting a small business is the ability to build out a diversified product line that is complementary to the headline product(s). It’s hard to imagine a successful business called “Burgers and Scarves,” right? As a good rule of thumb, a well-thought-out product line allows for the customer to upsell themselves. You want them thinking, “I’m having a burger, y’know what I’m going to have some fries too.”
Your sense of space and how to use it will be slightly different depending on the focus of your craft. If you are building furniture with hand tools, you will be able to make do with less space (under 300 sq ft.) than if you’re using mainly power tools and building sets of cabinets (over 400 sq ft.). Some 3D mod­elling with a program like Sketch-Up or some 2D layouts on graph paper with scaled cutouts can allow you to experi­ment with arranging your space and how much of it you will need. You should include not only the tools, benches and storage that you currently possess but also enough room to tackle new types of projects and new tools that you antici­pate needing down the road. When you think you have a layout that works, test it out by mentally working through a range of different projects you might tackle and the needs you will have for material storage, assembly and finishing. Then revise as necessary; this process will allow you to hone in on a general square footage and layout ideas that will set you up to move forward.
If you want that homey cabin feel inside your van, then lining the walls and/or ceiling with tongue-and-groove paneling is a good choice. Paneling looks awesome - the cedar paneling on our ceiling is one of the defining features of our van. And we cut ours to random lengths and stained it several colors to really give it that mismatched, rustic look.
Once you’ve planned the basic layout of your workshop and have added all the tools and speciality appliances you need, take a last look at the overall design to make it aesthetically pleasing. Add overhead lighting for general illumination and task lighting over your work stations so you can see your project clearly. For maximum flexibility, you can mount clip-on work lights to nearby shelves and point them where you need them, knowing you’ll be able to move them about as required for different projects.
I save all my back issues of The Family Handyman magazine and love the projects and repair tips. The trouble is, I’m not always ready to do the project when the issue arrives. To make my favorite articles easy to find at a later date, I put a stick-on label on the cover and then add notes for easy reference when the time comes to do the job. — Willie Schreiber. Plus: Check out this small workshop storage solution.

Let’s say you’re a Brooklyn-based hipster and you want to follow your lifelong dream of opening your very own artisanal, organic lemonade stand. You’re planning on stationing your retro lemonade stand along a busy road in Williamsburg, Brooklyn. And maybe you want to hire a couple of college kids to collect the money and serve your customers, (probably while wearing some painfully cool 1970s punk band t-shirts). You’re only thinking about it semi-seriously. It might be something you’re going to do when you’re not focusing on your real career as an aspiring DJ.


Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
Wow that’s a lot of assuming and supposing :) no shop right? no tools right? a place to work and tools for under 3K right? . This ones easy buy a pocket knife, set in your living room and whittle . So far you have $20 spent for a pocket knife. You might need another $200 for a decent vacuum to clean up all the shavings you made in your living room.
I think it would work pretty well for a music festival, I don’t see why not. I wouldn’t say it is robbery proof, but generally robbers are looking for quick and easy targets, like a purse sitting on the front seat, just smash and grab. If someone really wanted to rob what was under they platform, they surely could, but they’d need more tools and more time to do so. And they don’t even know if there is anything good under there… I’d like to think of it as a really good robbery deterrent.
The core criteria of small business site selection will always be foot traffic and ease of access. In places like New York City, this means being by the subway or on a busy street. But for most of America it’s about considering traffic flow and parking accessibility. Ever see three gas stations at the same intersection? They are all picking off different traffic flows because they know customers are looking for the shortest possible detour.

I’m picking up a 4×4 Extra cab pick up tomorrow and selling my current 97 Tacoma. It’s older and it’s got a lot of miles but it still has a lot left to go. Mine is available in the 3 grand range. They’re hard to find and all the rust free trucks are out here in the west but mine is one example of many good Tacos that are available at an affordable price that will fit the bill perfectly.
Disclaimer: The content on this website is provided for information purposes only, and should not be interpreted as professional advice. You should perform your own research and consult with a qualified professional. Individual results may vary. Through this website you are able to link to other websites which are not under the control of discountra.com. We have no control over the nature, content and availability of those sites. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.

It almost goes without saying that everything about your shop's design should project the right answers to each of these questions. But in today’s market, you have to go one step further. In our digitally connected world consumers have seen it all. The true art of compelling store design is in telling a story about your business, while simultaneously anticipating the needs of your customers. It’s all about the surprise and the delight.
Garages are usually dark, which makes setting up task lighting a priority for a productive workspace. Track lighting is an easy option to install and gives your some directional overhead lighting, but it can cast shadows (especially if the light source is behind you while you work) and you’ll need another lighting source for task and overall room illumination. A simple, adjustable work lamp is helpful for soldering or when you need bright focused lighting.
Whether you end up looking at self-checkout counters, fancy lighting systems, special refrigerated cases, or any of a countless number of options, never forget that these are only tools to help accomplish your main goal. Your store needs to create an environment where customers want to be, where they feel comfortable and appreciated, and where that experience will prompt them to purchase (and hopefully encourage their friends to do the same). Equipment and technology decisions should always be made with your customers in mind.
I framed and sheathed each wall individually and then stood them up with the help of long 2x4 braces.  My neighbor let me borrow his framing nailer, which made things go much faster.  I added a second cap of 2x4 on the top to make the walls a little more rigid.  I then laminated 4 2x4's to construct a ridgeboard.  I nailed in some temporary 2x4 supports and had a friend help lift it into final position.  Once all of the rafters are cut and nailed into place, the supports were removed.
A very simple countertop but one that should work great for our workshop, now we’ve already applied one coat of polyurethane to kind of seal up the plywood. Now we’ll be applying another coat once that dries to give it a little bit of durability because this thing will get a lot of abuse. Now Tim’s applying the same kind of clear sealer to our little rolling workbenches here, and I think this is a great idea, we’ll be able to roll these out, lock down the casters on the bottom then you can have a drill press or any other bench top tool that you can work on, then when you’re finished with them you can roll it right back, tuck them up against this wall and it serves as a good storage unit and gives you the chance to keep the workshop wide open for some of the larger projects we might be working on.
I think the music comment was about speakers for playing music. I put a few 8″ in ceiling speakers in from MonoPrice.com ($60 / pair I think) and love them. A space that big would probably need at least 3 pairs. You’re not throwing a rock concert with them, but they provide very decent background music for not much cash. The speaker wire from MonoPrice is dirt cheap too. Just add a cheap receiver to drive them. Of course, you probably don’t want to spend that cash at the moment. But it’s a good starting point for the future.
As part of my antique restoration work I do a lot of faux finishing – hence the supply of stains and paints. Since I didn’t want to dust the house, the new shop is not connected to the house heat and air system. But, having just finished our first winter I now know the shop didn’t get below 45 degrees – and, the oven in the corner can make the shop toasty in no time at all.
We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.
Household vacs are not designed to handle large quantities of sawdust or wood chips. Their filters clog up quickly, greatly reducing suction. While you can get away with using a small cordless vacuum for small messes, a shop vacuum offers greater power and capacity. Whether you already own a shop vacuum or are shopping for your first, consider purchasing disposable bags or a washable and reusable CleanStream filter.
There are a variety of structures to choose from when starting a small business. However, the most common business structures include sole proprietorship, partnership, corporation, and S corporation. The structure you choose determines which income tax return form you have to file, which, you guessed it, dictates your legal and financial responsibilities as a small business owner. Because of this, you’ll want to make sure you understand the options that are available to you and weigh the pros and cons before incorporating your business.
Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.
Congratulations !! I think 62 days is quick ! thats a big project. Now that its done and you got to get everything else set up it kinda sucks that you will also need to start making the payments, yuck. However I think it will be a good investment as your show continues to grow . I certainly love it ! I look forward to what you have in store. Thanks
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop.
×