This sturdy 30-in. x 6-ft.-long DIY workbench is the ultimate in simplicity. It’s made from only fifteen 8-ft.-long 2x4s and one sheet of 1/2-in. plywood. Learn how to build a workbench by following the cutting diagrams to cut the parts: Figure B to cut the plywood tops, then Figure C to cut all the framing. Use the lengths provided in the Cutting List (see Additional Information below). You can either screw the framing together with 3-in. screws or hand- or power-nail it together with 3-in. nails. Screw the plywood down with 1-5/8-in. screws.
1. My vehicle is a Ford F-150, which is not great for off-road travel but is by far the best I’ve ever had for mobile living. The 6.5-foot bed is perfect for my 6+ foot height, and I can probably haul everything I own other than my home furniture in the back of it. How long is the bed of your Toyota? I’ve always assumed a small pickup would tight length-wise for comfortable sleeping.
It's a well-known fact in the retail community that in North America, 90% of consumers turn right unconsciously upon entering a store. The first wall they see is often referred to as a "power wall," which acts as a high-impact first impression vehicle for your merchandise. So, be sure to give it extra special attention in terms of what you choose to display and how you display it.
A table saw is one of the most important tools in the workshop for its ability to make long straight cuts. It will also cross cut with ease and if you don’t want to cut clean through a board you can adjust the height of the blade to make a dado or rabbet. A handy feature with the BTS10ST table saw is the vertical stand which also saves on storage space.
Do you have 3 goals left? Great! That's the perfect number. Do you have more? That's okay as well. If you have more time to work on your business, then you may be able to accomplish more then 3. But it also depends on the type of goal you are trying to accomplish. I just recommend not trying to over achieve in fear of not accomplishing everything you set out to do. 
Disclaimer: The content on this website is provided for information purposes only, and should not be interpreted as professional advice. You should perform your own research and consult with a qualified professional. Individual results may vary. Through this website you are able to link to other websites which are not under the control of discountra.com. We have no control over the nature, content and availability of those sites. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
Ideas on how to Improve your Workspace – We can all do with some ideas on optimizing workspace. The guide has a lot of information about how to improve your workshop to be more efficient and improve workflow. This includes the costs of improving your shop, as well as hacks you can do yourself to improve efficiency and storage space for less. You’d be amazed at what you can do with even a small room. You just need someone to point you in the right direction.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
You’ve probably considered what goods and services you’ll be offering, but have you researched the cost of sourcing your raw materials? How about the cost of turning those raw materials into your finished product? Do you understand how much you’ll need to charge for your products/services in order to cover the expenses of renting a space, paying employees, leasing equipment, and paying for permits and regulations? Moreover, have you considered if the answers to these questions will provide the kind of operating margin you’ll need to pay yourself a salary?

I live in Northern Va and have the same concerns. I save those little silica gel packets every time they come in a new product and put them in my tool drawers. I also salvaged a dehumidifier from a neighbor that I need to repair and set up in there. I use the wall mounted AC in the summer to keep it cool enough to work in there. Although I haven't gone back yet to insulate the ceiling, it stays really cool in there if i want it to be.
When starting a small business, many store owners underestimate the value of a persuasive shop design. What they don’t realize is that people are visual creatures. In fact, 90% of the information transmitted in the human brain is visual. Clear, consistent store design will ensure that you attract your ideal customers into your business by delivering a subconscious uniform message.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Great instructional! I built the bed of my 92′ Toyota pickup ext. cab the same way you did. I did some hard searching and found this camp pad, which literally fits the 40″ wide sleeping space perfectly. A few different mats from Exped will fit, but here’s the one I bought. Just thought you might like to know there’s an inflatable duo sleeping pad out there that works for your setup!
We have Eclipse Sunshades installed on our van. While they’re pricier than the cheap sunshades you’ll find at Walmart, they’re every effective. And since they permanently install on your windshield they’re much more compact - a big plus for living in a van. All we have to do is pull the shades across and velcro them together in the middle and we’re protected from both the sun’s rays and prying eyes.

A grid floor plan, also called a straight layout, is a very efficient use of both floor and wall space. With fixtures and displays running parallel to walls, a grid floor plan maximizes every inch of available floor space, including the corners. Grid layouts are easy for customers to navigate and for store owners to categorize. Plus, they offer plenty of end cap and feature wall exposure for promotional items and seasonal products.
As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
Well this is the same unit I have used for years so the noise level will be what it has been. I never turn it on without ear protection. In the future, I plan on building a little closet around the cyclone to help mitigate the noise to some extent. As for cycling the motor, I read that too. But the way I work, I just can’t do that. I have to turn it on and off as needed but I do try to limit it as much as possible by doing all of my heavy milling at once.
To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.
I didn’t want to get a truck with a million miles on it. I am not a trucker by trade; I got my CDL specifically for this project. I didn’t want to get into a truck and then have to worry about its structure, engine, and transmission—and then start building Optimus on top of it. That’s why I got a brand-new truck custom-built from Western Star to become Optimus Prime.
We’ve been focused on the first category so far, but there is also an allure to buying an existing business. These enterprises will often come with brand awareness, a customer base, trained employees, an established supply chain, and most importantly (we hope), demonstrated profitability. As a result, countless startup risks can be diminished by taking this route. That is only true, however, if you make sure to carry out thorough due diligence on the existing business.
Next up are the chisels, you can start with a couple of sizes and build from there. When looking at saws, for joinery a dovetail saw is a good place to start, with a choice between western style or Japanese. For precise cuts across the grain, cutting tenon shoulders, and defining the edges of a dado a carcass saw also makes a good complement to the dovetail saw.

Thanks! Yep, the canopy clamps and the grooves in the bed liner are the only things holding the side shelves and sleeping platform in place. You just pop off the clamps with a ratchet and the whole things lifts out / slides out easily. That’s what I did to treat the wood after construction, takes maybe 15 minutes to pop out. Very modular. It’s been in there for more than two years now, same wood, and everything is still looking good and working fine. I like it!

However, while this product might draw the customer through the door, it will not, on its own, make your business a success. A strong small business has to be resilient to the challenges the world can throw at it, whether that means an economic recession, sudden fluctuations in commodity prices, or problematic suppliers. And a big part of resilience comes in the form of diversification.
If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
Couldn’t disagree more. Still got the same setup a few years in. As mentioned the sag is minimal (not non-existent), I place a small removable 2×2 near the tailgate so I can hop up top. You’re not building a home up to code, you’re building a practical truck camping solution, and in my extensive experience it is more than fine. You can do thicker plywood, but realize that it will be much heavier and more cumbersome to move.

The small apparel boutique pictured above really nails these traffic flow details! A roomy entrance offers clear sight and travel lines to eye-catching power walls on the right, and an inviting seating area towards the back. These lure customers into the store with the promise of treasures and comfort within. The shop even has a left-side checkout midway back. Someone really did their customer behavior homework on this retail store layout.


Congratulations on your new shop and all your success. I’ve watched all of your videos and someday if I have the money I would love to join your guild. I started a small workshop in my grandparents basement and someday I hope to start a small bussiness. Your website and videos have been the most informative and the most inspirational to me as a beginning woodworker. Thank you for sharing all your tips and hard work with people like me. I look forward to watching your videos for years to come.
“Zone design successfully helps shoppers locate what they want while exposing them to products that enhance the ones they are buying. Increased transaction totals are a natural byproduct. Products are categorized by use into Zones, such as ‘kitchen/cooking,’ ‘entertaining/dining,’ and ‘home decor,’ with inventory range and stock levels determining the size of each Zone.
Hey, you ever wonder what it look like behind the scenes at a home improvement show? Well here’s a little glimpse of it. This is a storage building I’ve had for awhile and we use this for storage and materials and props we use on the show and it’s also used by my construction company. Well this part of the building has kind of turned into a little bit of a dumping zone, where people just dump things that they’re not sure exactly where they go in the rest of the building.
Though store planning software isn’t a necessary tool for the average small retailer, it can certainly come in handy if you are looking to develop specific planograms, such as for the holiday season or a special event. Store design software is more common for multi-location retailers that want to deploy the same planogram in multiple places. Either way, if you are looking to build planograms, DotActiv offers a handy free tool.
How to Optimize a Small Layout – Not everyone has the room to have a huge shop selling everything. Ralph guides you through making the most out of a small shop layout. This includes optimal machine placement, where to set up shop, the tools needed, and lots of other consideration. The guide walks you through every aspect of setting up your shop – going into details without having it be overwhelming. It’s ideal for beginners that are looking to set up shop. 
×