You can see in this step how I notched each rafter to fit more securely to the walls.  I also used a metal hurricane strap to secure each rafter to the wall.  Even though this was not required by code, I felt my tools were far to valuable to be left to chance over such an inexpensive solution.  The walls are a simple board and batten system.  The 1x3 trim covers the joints of the 4x8 OSB.  They make much more high quality sheets goods to use as siding.  However, the cheapest I found was $35 a sheet and the OSB was about $5 a sheet.  I sealed the OSB and painted it with exterior paint.  If I run into problems in the future, I can just add a second layer of more durable material or simply have siding installed.  It has held up very well over the past couple years and I see no need to spend more money on it now.
I don’t own a dog, but I have taken my buddy’s two dogs out with us to the trailhead at least. Not sure that I have great recommendations for how you would go about living in the truck with your dog. All we really did was lower the large wooden deck to the bottom position, throw down some soft doggy beds and pillows, then cover it all with a giant blanket which also covered like the side bins to keep dog hair from getting all over. It was nice and cozy for the dogs while driving down the road. Then we just put packs and other gear on/in the side bins. We used some big metal clamps to secure the blanket to the side bins and keep it from falling down or sliding around. I would think avoiding any carpeting would be a good bet, just go with blankets and things than can be taken out, cleaned, and you can sweep out the back.
One site that I found a year or more ago was Life Remotely. They converted their truck to accomodate 3 people traveling from Seatle to the end of South America. They camped in tents most nights and some hotels/hostels but did a lot of conversions to their truck. Plus they blogged the whole time which is pretty cool if you want to take the road trip international.

I totaly get not wanting to get into the cost part of the shop. We just went through a house renovation, and my stock answer to the ‘how much’ question is either ‘enough’, or ‘enough that was right for us’. There is a quality of life or utility aspect that every person needs to figure out for themselves. And, I would think not having to bounce around from garage to garage anymore has gotta be worth something!
Many small business owners start on a shoestring budget, intertwining their personal and business finances, supporting the business with their personal credit cards, accepting payments into their personal checking account, and even submitting tax returns that mix up personal and business finances. While this is common, it can create tax headaches, make bookkeeping more time consuming, and, most importantly, can also interfere with the proper evaluation of your business.
My enthusiasm was kindled and I made friends with Surrey Timbers for more 'exotic' wood. My next purchases were a Drill Press and a Scroll Saw from Axminster Tools and I set to work. An excellent piece of Yew followed by some Thermal Ash has so far produced 4 cribbage boards. I then obtained a Palm Router which, after some practice, I find better for the more intricate work.
Firstly, more and more consumers are rebelling against the generic offerings of big-box retailers and seeking out the unique, personal touch offered by small, local business. You can leverage this message by weaving yourself into the fabric of your community. Canadian yoga apparel retailer Lululemon has enjoyed explosive growth thanks to their ability to do just this. According to their website, “A Lululemon store is so much more than a place to shop. It’s an education centre, a yoga studio and a meeting place. It’s a local hub for educators, ambassadors and guests to gather to learn, sweat and connect. It’s our lifeline to our communities and the soul of our company.” Lululemon uses free events to make people feel that they have a sense of ownership over the brand, and you can too! Getting people through your door is 90% of the battle and event marketing definitely can bring in crowds.
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but out­side the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials move­ment. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
I bought an energy-saving outlet strip for my TV and its components. One outlet controls several other outlets on the strip, so when I turn off my TV, the adjacent controlled outlets for my VCR, DVD player and receiver sense that no current is going to the TV anymore, and those outlets shut off. Then I decided to try it out in the shop. I use it with my router table, disc sander and orbital sanders, so when I flip one of them on, my shop vacuum also starts up to take care of dust collection. It also has two outlets that are independent for other accessories you’d like on all the time. You can buy the outlet strips at amazon.com. One choice is the Belkin Conserve Socket with Energy Saving Outlet (about $30). — D. Linley. Plus: 30 more smart tips for working in your home shop.

A good starting point here is to write down two or three keywords that you think define your brand and then allow all your design choices to be guided by those words. For example, a local cheese shop could be organic, artisanal, and authentic; a wine bar could be sophisticated, 1920s, French; or a local specialty food store could be gourmet, helpful, natural.
As part of my antique restoration work I do a lot of faux finishing – hence the supply of stains and paints. Since I didn’t want to dust the house, the new shop is not connected to the house heat and air system. But, having just finished our first winter I now know the shop didn’t get below 45 degrees – and, the oven in the corner can make the shop toasty in no time at all.
The key to success here is having clear processes written down, promoting from within whenever possible, and remaining open to change. You’ll want to balance your desire to educate your manager on how to manage your business with an openness to feedback and new ways of doing things. You’ll also want to take advantage of the technology available to keep you abreast of things like real-time sales data for all your locations, no matter where you are.
This will be a personal matter, depend­ing on whether it will be helpful for finishing or sharpening. However, it is a good idea to look beyond your current use of this space to the next owner. Would it be beneficial to add plumbing hookups so that the shop could someday be an apart­ment, or an art studio, or an extension to your house? It could add to the resale value of your house to be able to create as flexible an area as possible by roughing in a bathroom and even a kitchenette area if you can. If this is done when wall cavities are open or before the slab is poured, your forethought could pay dividends but not cost much up front. 
Leslie recommends that retailers provide some type of seating for both customers and anyone who is accompanying them. Shoppers do get tired and so do their friends and relatives who are along for the ride. Why not offer them a chair? Seating can be as simple as stools near the checkout or a lounge area near the dressing rooms, like this fun setup below:

This is a great project if you carefully consider your needs first. I left out the vise and tracks, but had no problem hand picking good 2x4 stock at the big box stores. I did use maple on the top sides in case I ever decided to add tracks, but it was not a budget buster by any means. The cabinet and drawers were a first for me and a great learning experience. I also added retractable casters so I can easily move the workbench around my shop. Love the workbench!


Radiation is heat transferred through air or a vacuum- think the heat radiating off of a fire. In a van, the biggest source of radiant heat is your windows. Sunlight (radiant heat) shines in through the windows and heats up the inside of your van. Using a reflective window covering will help deflect radiant heat and keep your van cool. Reflective surfaces also help keep radiant heat inside the van during the winter.
We do not recommend using Reflectix to insulate your walls or ceiling. Without an air gap, the R-value of Reflectix is about R-1. Even if you have the recommended ¾” air gap next to the Reflectix, the R-value per inch is less than R-3. There are much more efficient and cost-effective insulation materials out there for these purposes - you’ll be better off filling the space with rigid foam board.
Apps in this scenario would be able to fully function without any sort of network connection. Historically, examples of standalone apps might be your settings app or the camera app that comes with your device. Even today though, those apps usually have some interaction with the network. For example, you can share a photo from your camera via messaging.
​Buying rough cut lumber saves a ton of money.  Buying lumber that has had all four sides surfaced (s4s) will cost roughly 4 times as much as buying rough cut lumber.  Let's look at an example: I'm going to build a table that will require 50 board feet of oak.  If I buy finished oak it will cost around $5.5 / bf or $275.  Alternatively, I can buy rough cut oak at $1.25/bf or ~$65.  In this one project I've saved $210.  That's enough for a new power tool.
Up until about ten years ago, if you were in the process of starting a small business and wanted to use all of the technologies listed at the start of this section, you would have needed to take out a second mortgage to cover the bill. Investing in retail technology has historically involved expensive hardware (including an in-house server), large upfront software costs, and hefty ongoing bills for customer support or repairs when things went wrong. Innovators were targeting large-scale enterprises like Coca-Cola, not local mom and pops, so the packages and price points were designed to match.
This will be a personal matter, depend­ing on whether it will be helpful for finishing or sharpening. However, it is a good idea to look beyond your current use of this space to the next owner. Would it be beneficial to add plumbing hookups so that the shop could someday be an apart­ment, or an art studio, or an extension to your house? It could add to the resale value of your house to be able to create as flexible an area as possible by roughing in a bathroom and even a kitchenette area if you can. If this is done when wall cavities are open or before the slab is poured, your forethought could pay dividends but not cost much up front. 
Also, heard of anyone camping in an Accord sedan? I’m wondering if it’d be worth it to buy a new Tacoma to convert into a dirtbaggin’ vehicle or if I should try to make it in a sedan. Lots of variables… I’ve got the cash but it’d eat into the “cushion” I have for living on the road (about 50% of it). OTOH I could buy a used Tacoma, but they hold value so well it’d seem like long term it’d be best to get it new. I’ve seen some with 250 miles sell for $8,000+. Thoughts on getting a new truck using my beat-up sedan?
Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.

Just stumbled across your article and it’s right on time as I am about to launch a special events venue (ballrooms, meeting rooms, outside garden area, outsourced caterer, etc). Not sure what type of zoning this business falls under. I read that zones are usually for office, retail, industrial and leisure. Any idea what type of zone I should be looking for? Also first time trying to get a commercial space for this type of business, any specific suggestions?
Once you have your space secured, hang some pictures in the windows that illustrate what’s to come. It’s also a good idea to provide leaflets that people can take away with them and hang a clipboard and pen on the front door where people can sign up to hear more about your business. This list is pure gold! So once you have it, why not stage a launch party and invite the local community (and local journalists). The first step for any business is always getting people to try out your products!
One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
Lastly, and perhaps most importantly, your size should make you lean. Every single aspect of your store or restaurant can be tweaked and optimized to ensure more and more customers are coming through the door. As you experiment with strategies on Facebook or Twitter, introduce a new email marketing techniques, or simply erect new signage outside of your store, you have the chance to measure your success and react quickly to failure.
Tip: Save money on specialty displays! Many manufacturers offer retailers low-cost or free specialty display fixtures designed to highlight their branded lines, like the one pictured below. These make great speed bump or outpost display units on a tight budget. Your product line reps can tell you if they’re available, plus provide merchandising and display advice.

Well, my workshop is finally complete and I’m ready to take on just about project that comes down the line. And I’m pretty well set up here. I’ve got a great workbench, plenty of table space over here that easily rolls around the shop if I need it, lot of storage space down here, I can tuck these tools away or bring out any new ones that I need. And as you can see I’ve got plenty of supplies to tackle just about any project.


Disclaimer: Reviews on FitSmallBusiness.com are the product of independent research by our writers, researchers, and editorial team. User reviews and comments are contributions from independent users not affiliated with FitSmallBusiness.com's editorial team. Banks, issuers, credit card companies, and other product & service providers are not responsible for any content posted on FitSmallBusiness.com. As such, they do not endorse or guarantee any posted comments or reviews. Post Your Comment
There is a profound difference between a good idea and a thriving business, but as the saying goes: “A journey of a thousand miles begins with a single step.” At a certain point, turning your dreams into reality is as basic as putting a plan in place and, step by step, making it happen. The good news is that there has never been a better time for starting and learning how to run a small business.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
The nomadic truck camping lifestyle has been incredibly freeing, not only is cheap and accessible to most anyone, but it can take you beyond places you even imagined. One book that I’d recommend to all newcomers to this lifestyle is Bob Wells’ How to Live in a Car, Van, or RV, which will help you better understand the ins and outs of this lifestyle.
The more outlets the better! I have a good mix of 220v and 110v outlets throughout the shop. I even included a few in the ceiling and the floor in hopes of avoiding power cords in the walkways. And although this contradicts my previous comments about over-committing, I picked locations that would likely work for various tool configurations. If at some point they don’t work for my setup, I just won’t use them.
It can become very difficult and time-consuming to constantly track the amount and purchase price of all your inventory, but it is hugely important to your bottom line. Every time you catch yourself saying, “Sorry, we don’t have that in right now,” you are leading your business in a very unhealthy direction. Not only does being out of something represent a lost sale opportunity, but in a world where consumers place a huge premium on their time, it could mean that you lose that customer forever while hurting your brand reputation in the process.

Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.


My husband is always hounding me about wearing eye protection whenever I use power tools. (Admittedly, I could be more diligent about it.) So, he recently glued some small magnets to several pairs of safety glasses and stuck them on all the power tools in our garage that have metal housings. Now it’s fast and easy for me to grab the glasses when I need them, and I’m reminded that my husband loves me. — Lisa Yanda. Here’s the other must have safety gear every DIYer should own.
Well this is the same unit I have used for years so the noise level will be what it has been. I never turn it on without ear protection. In the future, I plan on building a little closet around the cyclone to help mitigate the noise to some extent. As for cycling the motor, I read that too. But the way I work, I just can’t do that. I have to turn it on and off as needed but I do try to limit it as much as possible by doing all of my heavy milling at once.

Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.

Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.


One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
Conversion vans have some pretty sweet built-in amenities, including high-tops for extra headroom. Many have comfy captain chairs, leather seats, mood lighting, TV/VCR, and a rear bench seat that folds down into a bed. If you’re not picky about your living situation, this could be all you need to get started. And if you gut it and customize it yourself, the high top offers tons of great storage options that other vans just don’t have.
Although the market has even more options to build apps now than in 2015, there's also clearly more of a distinction in quality. The best app firms and app developers have further honed and distinguished themselves. They have more awards, stronger portfolios, better team members, and more specialized skills. The tools available have made it easier to build apps though, so there's also many more mediocre or low-quality options to build your app.
We have Eclipse Sunshades installed on our van. While they’re pricier than the cheap sunshades you’ll find at Walmart, they’re every effective. And since they permanently install on your windshield they’re much more compact - a big plus for living in a van. All we have to do is pull the shades across and velcro them together in the middle and we’re protected from both the sun’s rays and prying eyes.
With all the time and effort you've put into properly merchandising your products, the last thing you want is for incoming customers to hurry past them — this ultimately limits the number of products they'll purchase. One way retailers combat this is through creating breaks that force them to pause. These are sometimes referred to as "speed bumps." Essentially, this can be anything that gives customers a visual break and can be achieved through signage or special/seasonal displays.
Spacious pathways are a key aspect of good store planning. In fact, it tops the list of retail experts’ store design tips. Heshy Lovi, Sales and Marketing Director for M Fried Fixtures, recommends aisle widths of four feet or more. This, he says, ensures your aisles and pathways will be comfortable for all customers, including those using strollers or wheelchairs.
So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.
We don't have a Dometic CFX-50 in our van, but we wish we had gotten one for our build. This is a great little fridge that many vanlifers happily own. It’s rugged and durable, and it keeps your food cold for less money than many of the other fridges out there. It also has a nifty side-open lid, which makes it a lot easier to open with a lower clearance.

Most businesses must obtain a variety of business licenses, permits, and registrations before opening their doors to the public. As a small business owner, it is your responsibility to ensure that you are abiding all the laws and regulations applicable in your state and to your particular industry. You also have to research and apply for all relevant permits and licenses that apply to your business type and location. Remember, it is impossible to plead ignorance as a defense. It’s up to you to educate yourself. When in doubt leave it to the professionals. CT Corporation offers custom license packages that simplify the process for business owners. Click here for an example of what that looks like.
Depending on your situation, you may need to upgrade to 200 amp electrical service in order to meet the needs of your house and your shop. It may also be in your interests to add in a separate electrical service meter on your shop so that you can clearly write off electrical use for your business, or in future rent the space out and clearly separate out the utilities for bill­ing your tenant. Generally, you don’t want to skimp on the power to your shop or on the lighting you include.
After years of digging down under router tables, lifting the entire unit up to change bits, and then fighting to get the plate flush again in the table, I chose to spend the money to pur­chase a router table, fence, and lift system. I did a thorough review of these systems, and chose the Canadian made Jessem Rout-R-Lift II kit. The system comes with a solid steel stand, a phenolic table, an adjustable extruded aluminum fence, and their base model lift system. For budget reasons, I did not choose the hefty Mast-R-Lift, but I am quite happy with the lighter Rout-R-Lift II. It will last me a couple of lifetimes, so it is the right system at the right price for me in my one-man shop. Hats off to Jessem for making a great lift at a very rea­sonable price in the middle of a tough economy. The table is durable, and flat. The direct drive lift is smooth and precise. I mated the lift system to a mid-sized model 690 Porter Cable router, which has a fixed speed, and enough power to do any­thing I need. The Jessem system uses a bayonet type mount for the table inserts, a nice touch that makes swapping the table insert quick and simple. As with all my machines, the router table is connected with the supplied dust port to my shop dust collection system with automated switching. 
Hey Anthony, I guess the big question is what part of the country you’ll be sleeping in and what sort of weather you can expect… I would imagine when conditions are fine that a warm sleeping bag would be more than enough (I used to do that before I had a canopy). You’ll just have to worry about rain (snow?) and other inclement weather, but otherwise I don’t know why not. A cheap bivy sack from an army surplus store might be a good addition as well.
If you have a small shop, you're probably not going to have the option of milling your own lumber to square. So the easiest way to go is to buy boards in the thickness and width you'll need. When buying sheet stock at a lumberyard or home center, the employees there can usually cut boards or sheets down to approximate sizes for you on a panel saw–sometimes for free, but typically for a fee.
Hello! My name is Donna Jean. I love to read books and my job is to write a daily review of all the novelties in the world of eBooks. I allow only the best of them to be published on my website. I really hope to make our world more bright, beautiful and kind. You can participate by downloading any book from my site, and you will receive health, luck, kindness, and love, which will support you during all your life. Wishing your dreams begin to come true, and every tomorrow be happy for you. Thank you! ❤❤❤

After a year I am still arranging my MAN CAVE . Mine is 2,400 square feet with a 500 sq ft garage and 500 square for room upstairs that serves as gallery of my photos (yes I have several sins) and a conference room as well as any finished projects from the shop. I teach, probono middle school boys and girls in what the school calls an enrichment program. There I have named this the Water’s Edge Woodworking Academy. Actually it is open to my neighbors to build their projects when I am present. I am about one chapter ahead of them. When I told my wife last week I was thinking of an addition she told me “”over my dead body” Taking up extra room are two cnc routers … a Shopbot Buddy Alpha and a Legacy 5 axis cnc machine.


Budget Toilet: Luggable Loo. With the Luggable Loo from Reliance Products, you can turn any 5-gallon bucket into a portable toilet for your van. Make sure to line your bucket with a trash bag or toilet waste bag - then once you’ve done your “doodie” just tie up the bag and dump it in the trash. Reliance also sells deodorant chemicals that will make it easier to live with your new roommate
While not as large as I would have liked (is a wood shop ever big enough?), it is about twice the size of my previous shop. It measures about 12 by 25. Fortunately I had managed to find quite a bit of shelving before the move, so I was able to install shelving along two walls. And the work benches were made from wood salvaged from packing crates from Europe and left over yellow pine car siding and flooring from remodeling the old house.
Now, this is kind of an odd situation here, a few years ago when we bought this building there was a concrete block wall around here and a large drain right in the middle of the floor. Well the drain will certainly come in handy for any cleanup in the shop but the walls kind of left us when we removed those kind of left us a little divot and a little bit of damage here, so to make this nice and smooth so that our rolling workbenches will roll around real nicely we’re having to do a good bit of floor patch.
Having a plan of action is key to learning how to start and run a successful small business. Whether you are looking for funding from a bank or angel investor, or are lucky enough to completely fund your venture on your own, an articulate and well-thought-out business plan will help you define what your business stands for and what it intends to become over time. As the age-old saying goes: “A goal without a plan is just a wish.” Don’t put your business idea in the hands of fate. Plan thoroughly, give yourself some benchmarks for success and be prepared to innovate as you go.
To make sure you account for any existing obstructions, it’s a good idea to make a measured drawing of your workshop area on graph paper, noting existing furniture, built-ins and large items on the plan as you go. For example, a common one-car garage workshop layout has built-in tool cabinets and shelves around the perimeter where they won’t impede parking, but you may also have to get clever about folding work tables and saw horses that you can set up as needed in the middle of the garage when you’re working on a project (and cars are parked outside).
Our practical workshop is coming along nicely. We’ve created a big open space and added plenty of electrical power and lots of light. We’ve also added some great storage capacity using recycled kitchen cabinets and some old shelves. Now, with our tool compartment and work surfaces in place we’re getting very, very close, but I wanted to get a little input on the final details from some other folks who spent a lot of time making sawdust, so I asked my co-host Allen Lyle and our website editor Ben Erickson to look around and give us some of their ideas.
A good portable air conditioner will also remove excess water from the air, which is critical for keeping your stockpile of wood in good shape. Lumber should be stored in dry conditions so it doesn’t warp, so look for efficiency features that allow you to run the unit overnight in the summer as needed —without worrying about blowing up your electricity bills. Other good features to consider include a thermostat and variable settings that allow you to set your workshop temperature to the perfect level for your comfort.

People tend to buy cargo vans for work and hold on to them for years, so many vans on the market can be pretty beat up. Although you can find inexpensive cargo vans in good condition, it can be tough to find anything with lower mileage - so be prepared for all that comes with owning a higher mileage vehicle. Cargo vans also don’t offer much headroom. There’s no way even shorter people will be able to stand in one, and the lack of headroom also cuts down on storage space.
When it does come time to choose a long-term space and negotiate a deal, it’s important to remember that there is more to discuss than just the monthly rental rate. Subjects you’ll want to raise include the proposed length of your lease and options for renewal, responsibility for ongoing maintenance and repairs, payment of utilities, and obligations around property insurance. Parking rights are also essential for many, especially businesses located in a small shopping center.
On-demand apps incorporate many of the elements seen in apps with logins and social features. Like ecommerce apps, they also include a transactional component, because users need to purchase goods and services. Unlike social and ecommerce apps, however, on-demand apps essentially require two completely unique user experiences. For example, an Uber driver needs advanced mapping and routing functionality while a rider doesn't. Similarly, the driver doesn't need to do a payment while a rider does.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
×