Shop looks great Marc, I see the Clear Vue in the picture. I love mine, I used 8″ PVC for the main trunk line and came out of that with 6″ drops. It works great. I wound up building a collection bin instead of using a can, only thing I didn’t do was make the bin big enough. It holds more than the typical can but I still should have made it with more capacity. The 1800 with the 5 hp motor is stout.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
Woodworking isn’t just an overnight hobby, for most it’s a fun pursuit that lasts a lifetime. As your skills develop, the workshop becomes a place not just to build but to repair along the way. In a world where people are strongly influenced by consumerism, there’s a tendency to revert to a throwaway culture. But if you can fix before throwing away, then your tools start to make a return on their investment and have a bigger impact.
Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appro­priate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with hom­eowners and builders to make sure that the work will meet code and will endure.
Electricity was something we didn’t want to worry about at all in our van, so we went big from the beginning. We bought Renogy's 400-watt solar kit and two VMAX 155ah batteries. We mounted three of the panels on our van’s roof, and the fourth we attached to a folding stand made out of PVC so we could roll it out as needed. While the system works great and keeps us charged up, in hindsight it was a little bit of overkill - especially since we added a battery isolator.

First, decide on wax you would like to start with, there are three different kinds to choose from Ultimate Small Shop paraffin wax, soy wax, and beeswax. Paraffin wax is most commonly used in candles, this wax is found at most candle making stores. Soy wax is all natural, made from soybeans, and cleans up easily with soap and water. Beeswax is all natural too, and making beeswax candles is often easiest because you simply wrap a sheet of beeswax tightly around a wick then seal it with your thumb, which means no melting is required. To begin, spread newspapers around the candle making area. First, you melt your paraffin or soy wax and it must be double-boiled. Usually, you place a large pot that is about half-filled with water on a burner over low-medium heat, place a melter in the water, then gradually place wax pieces into the melter. When the wax has melted, you can add coloring or fragrance as desired. To make molded candles, cut the wick two inches taller than you want the candle to be, then thread it through the hole at the bottom of the mold, then plug the outside of the hole with putty. Place a pencil or similar item over the top of the mold and tie the top of the wick to it, centering the wick. If the mold is cardboard, plastic, or glass, heat the wax to 130 degrees Fahrenheit. If the mold is metal, then heat the wax to 190 degrees. You can use a candle or candy thermometer to measure this. Ultimate Small Shop Pdf When the right temperature is reached, lift the melter by the handle and slowly pour the wax into the mold. Let cool for twelve hours then refrigerate for twelve more hours, then your candle is ready to be removed. To make votives and other small container candles, you can use pre-tabbed wicks by simply placing them in the center of the votive candle molds or containers, then pour the wax mixture over and let stand for twelve hours, refrigerating the votives. By the time your teen is in high school, you probably aren’t taking as many pictures of them as you used to. I have to keep reminding myself that I only have a couple of years left and no time to waste trying to capture fleeing teenage memories. You might be thinking that I’m really organized to be already working on scrapbooking my daughter’s high school memories. To be honest, I have a shoebox full of pictures of my daughter waiting for me to get to someday. But if I wait until “someday” to continue taking pictures because I already have so many pictures I haven’t done anything with, then my daughter’s teenage years will come and go while I try to catch up. I don’t want to chronicle every detail of my daughter’s life (nor would she want me to!), but I was trying to think of some memories that she might want to laugh about and maybe even treasure someday. Ultimate Small Shop Guide Woodworking So how do you do that without ending up with pages and pages of memories? I decided to do two large (12×12) pages (facing each other in the album) for each year of high school. 

“Zone design successfully helps shoppers locate what they want while exposing them to products that enhance the ones they are buying. Increased transaction totals are a natural byproduct. Products are categorized by use into Zones, such as ‘kitchen/cooking,’ ‘entertaining/dining,’ and ‘home decor,’ with inventory range and stock levels determining the size of each Zone.

We're living in an age where we can order groceries, turn on the lights in our house, or get in a workout from the convenience of our phones, tablets, or other devices. Apps are a part of our everyday lives. They are increasingly giving us more free time or vying for more of our attention, depending on how we choose to use them. With that, here are some of the more important changes since we published our app cost article in 2015.
I think it would work pretty well for a music festival, I don’t see why not. I wouldn’t say it is robbery proof, but generally robbers are looking for quick and easy targets, like a purse sitting on the front seat, just smash and grab. If someone really wanted to rob what was under they platform, they surely could, but they’d need more tools and more time to do so. And they don’t even know if there is anything good under there… I’d like to think of it as a really good robbery deterrent.
Make sure to utilize the tax-specific resources provided by the SBA and the IRS to fully research your federal and state tax obligations. These include, but are not always limited to: corporate income tax, employer tax and excise taxes. For most small businesses, the right first step is applying for an Employee Identification Number, which you can do using this IRS EIN online application. Depending on your state, you might also need to register for a sales tax license.

You can typically find paneling in pine and cedar. Pine is cheapest, looks fine, and will do the job. Cedar is more expensive, but it looks and smells awesome - and it’s resistant to mold and mildew. Paneling comes in different thicknesses, but we recommend using ¼” (5/16”). Thinner paneling weighs less, costs less, takes away less interior space, and will bend with your van’s contours.

Ebates.com - Ebates is something I'll check after I've already found a deal that I'm going to bite on.  The rewards aren't usually good enough to compel me to purchase on their own.  But if you get an extra 3-5% cash back over your entire $250 budget, it can add up to an extra hand tool for doing nothing more than using their link to an online store.
Couldn’t disagree more. Still got the same setup a few years in. As mentioned the sag is minimal (not non-existent), I place a small removable 2×2 near the tailgate so I can hop up top. You’re not building a home up to code, you’re building a practical truck camping solution, and in my extensive experience it is more than fine. You can do thicker plywood, but realize that it will be much heavier and more cumbersome to move.

Chances are if you’re starting a new small business, you’re not afraid of a little risk. However, it’s also highly likely that you have invested a large amount of money in this new endeavor. It is only prudent to take sensible steps to minimize the impact of unexpected events, like the untimely death of a business partner, a lawsuit from a customer or employee, or a freak accident of nature.
Perhaps the most satisfying move I made was to automate the dust collection system. I used the iVACPro system to link all machines to the dust collector. When I turn on any machine in the shop, the dust collector fires up and whisks the dust into the bin. The system also has a programmable delay to allow the dust to make it to the bin before the dust collector shuts down. I set my system for a five-second delay. The system works flawlessly for my band saw, planer, and router table at 115 volts, and also my table saw and jointer at 240 volts. 
7. Illuminate your space in different ways. Lighting is important in any retail shop, but it's particularly critical in tight quarters. If a corner of your store is not well lit, that square footage is as good as lost, Langdon says. She recommends using a combination of track lights, lamps, sconces and picture lights. This mixture will not only ensure that your entire space is well lit, but it also will add flair and variety. "Picture lights are amazing. They give a wonderful glow," she says. "Think in terms of layers of light."
Shop layout is all about making the best use of space. Place your machines so that you have adequate “safe space” that you need to work around them. The “buffer area” beyond that is the amount of room you need to run large stock though a given machine, keeping in mind that buffer areas can overlap between machines. If you want to get more organized, buy some 1/4-inch squared paper, make scale models of each machine including the safe space around each, and place them on your model shop layout. Remember that buffer areas need to be long enough to put an 8' sheet through a table saw, or a 6' plank through your planer, for instance. I raised my planer, so that I can use the area above my router table to pass long planks through the planer – all it takes is some modelling, and a little shuffling, and you will find the layout that works for you. Each space will have chal­lenges; I had the area under the stairs that was wasted space, so I installed the dust collector there.

So, if you’re looking for a retail or restaurant location, you’ll want to figure out how many customers you expect to have, on average, and multiply that by 15 square feet. If you’re looking for an office space, you’ll want to forecast the desired size of your workforce and multiply it by 100 – 150. This will give you the size of the commercial space you need.
Assume that there aren’t any decent tools on craigslist or at garage sales, and keep in mind that I have absolutely no tools, dust collection, shop-vac, clamps, sanding & painting accessories, tables, materials to build my own tables/stands/jigs, or anything else—not even safety gear (you’re such a good buddy that you even let me borrow your extra set of goggles and your earmuffs when I used to come over).

Before starting your small business and opening its doors, it is important to take some time to define your end goal. While it almost goes without saying that this goal will be subject to change, it is only by recognizing and clearly articulating your long-term ambitions that you can provide yourself with a compass that will guide every business decision.


Nicole and I decided not to go public with the cost of the build. Although we are very open about most things, we are a little uncomfortable about making an expenditure of this magnitude public knowledge. Furthermore, unless you live in the Phoenix area and plan on building the same size shop with the same patio and with all of the same finishing touches and labor requirements, the price isn’t all that helpful to you.
Because two-sided market apps lack the specificity of on-demand apps, usually more features need to be built. More significantly though, it's much harder for a company to build each side of the market. Uber, for example, is focused on driving. Angie's List, on the other hand, has hundreds of different kinds of service providers. If it wasn't clear from the examples, both on-demand and two-sided marketplaces also have a geographic component. This means that they often start in one area or a subset of areas like Uber did in San Francisco.
The thickness planer can joint a board's face. On this simple jig, the stock is supported by twin rows of wood screws driven into a platform and adjusted to meet the varying clearances on the underside of the board. The stock rides the sled cup side up. Slide the board slightly sideways to adjust the screws, then seat it firmly on the screw heads for planing.

To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
When you’re first starting out, it can be hard to imagine that there are entrepreneurs out there complaining of having grown too fast. But for some, it’s not a problem that’s welcome. For every Ben and Jerry’s, (Ben Cohen and Jerry Greenfield turned a rundown Burlington, VT gas station into an ice cream empire), there’s a Zynga or a Living Social that has enjoyed incredibly fast-paced growth, let their operating costs get out of hand, and then had to engage in mass layoffs when reality hit. If you’re enjoying fast-paced growth, make sure that this is reflected in your operating margins, not just the metric of revenue. You don’t want to be the butt of the old retail joke: “We’re losing a buck on every sale, but we sure are making it up on volume!”
Like most things in life, we believe that entrepreneurship can be learned, you just have to be willing to put one foot in front of the other. Aftering reading How to Start a Small Business 101, you’ll be equipped with the essential tools and resources you need to succeed at planning, raising capital, and executing crucial day-to-day business operations.

I have a plastic bed lining on my truck, which also covered the back of the tailgate… I just popped the screws off, took off the plastic liner and drilled holes in the sheet of plywood to match those used by the plastic tailgate cover. Sorry if that doesn’t help you with your setup. But I’m sure you could just drill your own holes in the metal tailgate. Use the plywood cover as a guide for your screw holes…


Reactions are typically over-the-top excitement. Everywhere I go, there are people snapping pictures, taking videos, and giving me a “thumbs up.” Sometimes while on the highway, cars will go ahead of me about a mile or so and then pull over to get out and video me driving by them. Truck drivers are always getting on the CB radio asking about the truck.
I think the music comment was about speakers for playing music. I put a few 8″ in ceiling speakers in from MonoPrice.com ($60 / pair I think) and love them. A space that big would probably need at least 3 pairs. You’re not throwing a rock concert with them, but they provide very decent background music for not much cash. The speaker wire from MonoPrice is dirt cheap too. Just add a cheap receiver to drive them. Of course, you probably don’t want to spend that cash at the moment. But it’s a good starting point for the future.
Tip: Save money on specialty displays! Many manufacturers offer retailers low-cost or free specialty display fixtures designed to highlight their branded lines, like the one pictured below. These make great speed bump or outpost display units on a tight budget. Your product line reps can tell you if they’re available, plus provide merchandising and display advice.
×