You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.


Ultimate Small Shop goes beyond the ambit of Amazon, Home Depot and Lowe’s to help woodworkers start their workshop for less than $1,000. Woodworkers will find answers to questions related to the budget, planning, required tools, critical setup factors and more. The guide has been put together by Ralph Chapman, a coach with more than twenty five years of experience in woodworking. Chapman is the small shop expert and what he recommends is not speculation or best case scenarios. He has done it himself. He is now sharing his experience along with expert recommendations so you can begin your woodworking journey right at your home.
The small apparel boutique pictured above really nails these traffic flow details! A roomy entrance offers clear sight and travel lines to eye-catching power walls on the right, and an inviting seating area towards the back. These lure customers into the store with the promise of treasures and comfort within. The shop even has a left-side checkout midway back. Someone really did their customer behavior homework on this retail store layout.
I know in Missoula the garbage men do not like unbagged dust chips. They sent my friend a warning notice in the mail. Do you pull your drum out to the garbage and let the dust fly or dump it into a bag? My friend has garbage cans with 33 gallon liner which he pulls out of a sealed dust collection box beneath the cyclone… then he uses a hand truck to haul it out to the alley and then puts a fresh can in the box. It seems like a simple dust management method by not handling the dust by either scooping or dumping it out into a bag. I am always trying to think of ways to have less contact with harmful dust particles and I am curious as to how others handle the situation. Have a great weekend!
Simply get a one-inch drywall screw and drive it into the hole right beside the hook. You want to use a one inch screw because you don’t want to hit the wall behind it and you just drive the screw in until the head of it is tight against the hook, it’ll just act as a shim, and you’ll see once I get this all the way in, it lock the hook in place, and now when you take the tool on and off it won’t come off. The hook won’t pop out.

There is a profound difference between a good idea and a thriving business, but as the saying goes: “A journey of a thousand miles begins with a single step.” At a certain point, turning your dreams into reality is as basic as putting a plan in place and, step by step, making it happen. The good news is that there has never been a better time for starting and learning how to run a small business.

I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
Having a plan of action is key to learning how to start and run a successful small business. Whether you are looking for funding from a bank or angel investor, or are lucky enough to completely fund your venture on your own, an articulate and well-thought-out business plan will help you define what your business stands for and what it intends to become over time. As the age-old saying goes: “A goal without a plan is just a wish.” Don’t put your business idea in the hands of fate. Plan thoroughly, give yourself some benchmarks for success and be prepared to innovate as you go.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
By building your own workshop machines and jigs, you can create customized tools that include all of your favorite and much-needed features for less than half the cost of commercial tools (plus, get bragging rights for having the coolest woodworking shop in town). All you will need is a drill press, table saw, some common tools, and patience. Then, you can start following these step-by-step instructions to create homemade machines such as a sliding-top router table, jigsaw, downdraft dust collection table, a 24” band saw and more!
Gutting: We actually took on a pretty big project when we bought our van because it came with a preinstalled wheelchair lift that we had to remove. Unbolting all the parts took both of us working on it for a full day, and it wasn't the most glamorous job. The good part was that we were able to sell the lift and the reclining bench seat for a combined total of $260. If there's anything to remove from your van, do this first.
Overall I am very happy with the final results and I can’t wait to get back to making sawdust. The first project to be completed in the new shop is going to be a Queen Size Platform Bed for one of my favorite clients. I mentioned in a previous post that one of my goals this year was to get back into doing client work and this is me making good on that promise. I can’t wait to get started!

Power outlets are also needed for lighting, heaters, AC units, radios, televisions, CNC machines, 3D printers, and computers—all of which you’ll find in many workshops (although maybe not together, and maybe not all in your garage.) You simply can never have too many outlets and it’s much safer to have too many than not enough. Bring in an electrician to help install your outlets and setup 220v power if needed for larger shop tools.

At a time when you’re focused on getting in front of customers as quickly and as often as possible, it can be hard to think about official requirements like registering a business name or deciding on a legal structure. Still, now that you have decided to start a small business or buy an existing one, one of the first critical steps is determining the business entity that's right for you.

So what’s the downside? Well, for starters, RV conversions aren’t exactly known for quality. Most manufacturers use cheap (i.e. shitty) materials, and just don’t build their vehicles to withstand the stresses of full time living. You’re also locked into a pre-designed layout, so it will be a lot more difficult to customize how everything functions.
I don’t think you have run into this problem, but I have to deal with condensation in the cap as I live in a moist climate. I was thinking of an old van type roof vent with fan for active ventilation, or drilling holes along the side of the cap, inserting short cuts of pipe with fine screens (mozie land), and capping them. This way I could control for rain, cold, etc., but create some passive cross ventilation at roof level.
That headline struck me as discouraging. As an entry fee, $5,000 seems high enough to exclude a number of potential woodworkers, myself included. Christiana softened the blow by saying that used tools could cut the cost roughly in half. That figure seemed much closer to my experience, which involved buying a mix of new and used tools. Having said that, buying the right used tools is much more difficult than buying from a catalog or dealer who stocks everything needed to build a great shop. It requires a bit of guile and a good plan, but the payoff is worth it. Through careful choices and good fortune, I was able to outfit my shop with a blend of new and used tools for around $2,000.
One of the things that draws me to the online woodworking community is amount of passion people show are willing to share. Your shop build is a fine example of your willingness to let us in on your passion. You could have said “I’ll be back in a few months when its done” and most of us would have waited but instead you turned it in to a summer of updates and dream shop discussion. Thanks!
Enter the garage heater. These space heaters are specifically designed to warm up wide open areas and to function under much tougher circumstances than you’re likely to find in the average house. A well designed garage heater will offer at least 5,000 watts of heating power — enough to warm 750 square feet of space. A smaller heater might take off a bit of the chill, but to really warm your workshop — and keep it that way — you’ll need a heater of this size.

The subfloor provides a stable layer - basically a sheet of plywood - for your floor to sit on. You’ll see a lot of van build videos on Youtube showing a ¾” subfloor, but that thickness just isn’t necessary in a van. The thicker the subfloor, the higher the cost and weight, and the more valuable interior space it takes away. We recommend using ¼” plywood for your subfloor, which is plenty thick enough for a van.
First, decide what your budget is and start searching right away! Even if you're not able to purchase a van right now, knowing the market and how quickly things sell is helpful. Get an idea of makes and models you like, and you'll also start to understand what is a good price for a van in your area. Each country, region and city is a bit different.
According to a recent digital marketing survey conducted by Clutch, 74%of small businesses surveyed had a company website. Of the businesses that said they do not have a website, 9% said they planned to build a website in the future, while 10% said that that they are unlikely to build one. One thing is clear, small business owners are starting to join the digital revolution and are reaping the rewards in terms of increased customer loyalty, growing word-of-mouth, and most importantly, increased sales.

I have a plastic bed lining on my truck, which also covered the back of the tailgate… I just popped the screws off, took off the plastic liner and drilled holes in the sheet of plywood to match those used by the plastic tailgate cover. Sorry if that doesn’t help you with your setup. But I’m sure you could just drill your own holes in the metal tailgate. Use the plywood cover as a guide for your screw holes…
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
Now that you have your goals mapped out and you know the exact tasks that will help you accomplish them, I want you to pick a day of the week (preferably Monday or Friday) and start planning the week ahead - don’t skip this step, never skip this step. Schedule which one these tasks will happen on what day of the week. So you are literally pulling the tasks from that spreadsheet and placing them into this weekly planner. It’s important to keep in mind deadlines (the ones you set for your goals and when they should be accomplished) and the amount of time it takes you to do a task. You may also want to write down which day it’s due, and who is responsible for this task (if you work with a team).
Do you carry items that bring your customers back time and time again? Consider placing these primary and similar secondary product lines toward the back of your store. Or, if your stock is constantly changing and you don’t carry replenishing goods, place your sale items toward the back. That way, customers must pass your new items and promotional displays on their way to check out the deals in back.
Plus, taking the time to put pen to paper should benefit you as the small business owner as much as any potential new employee. Creating this kind of central resource about best operating practices will force yourself to formulate your thoughts and be clear about exactly what you want. Whether that means codifying sales procedures or deciding who can take cash from the cash drawer, you’ll have a clear and consistent company policy, something to which most employees will respond favorably.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
We're living in an age where we can order groceries, turn on the lights in our house, or get in a workout from the convenience of our phones, tablets, or other devices. Apps are a part of our everyday lives. They are increasingly giving us more free time or vying for more of our attention, depending on how we choose to use them. With that, here are some of the more important changes since we published our app cost article in 2015.
After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appro­priate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with hom­eowners and builders to make sure that the work will meet code and will endure.
Using six pipe cleaners, you can make your own skeleton. Bend one pipe cleaner into two for the backbone. Twist another around the bottom of the backbone to make into the legs. Do the same for the arms. Join two pipe cleaners and twist them around the backbone leaving some space forming a ribcage. Ultimate Small Shop Woodworking Twist the last pipe cleaner for a head and glue on some eyes. Hang with a rubber band for a bouncing effect. Your kids will love making Halloween crafts with pipe cleaners. But be careful when cutting and keep them out of their mouth. Going trick or treating? Why not make a special jug to collect candies? Cut off the top two inches of a gallon milk jug. Soak to remove any labels. Paint orange. Once dry, paint or stick on eyes nose and mouth resembling a Jack O’Lantern. Use fluorescent paint for a nice effect. The jug can be kept for future reuse. Using glue and food coloring, you can make a see-through painting. Paint a Halloween image onto a piece of plastic wrap. Before the mixture dries, put another piece of plastic wrap on. Cut it out and hang it in front of a light source for a see-through effect. You could also frame the plastic pictures using wood or cardboard if you want them to be longer lasting. Make some hand printed spiders. Ralph Chapman Ultimate Small Shop Apply black paint to your palm and 4 fingers leaving out the thumb. Place palm onto a piece of paper. Turn the paper 180 degrees and print again making sure the palm overlaps. Add some wiggly eyes using either paint or sticks. This is suitable for even 2 or 3-year-olds. Make your own blood. It is less expensive than buying ready-made blood from the Halloween shops. It’s not difficult; all you need is Karo syrup and food coloring. While you’re at it, why not make some slime using glue, water, and borax powder. This is an advanced Halloween craft, so take your time and be careful. Using apples, you can make dried, shrunken heads. Peel the apples and coat with a mixture of lemon juice and salt to prevent browning. Carve out a face of eyes, nose, and mouth. Do not worry about the finer details as they will probably be lost when the apple dries. You can use whole cloves for the eyes and rice grains for the teeth. Let the apples sit out in a warm place for about 2 weeks. If you don’t have 2 weeks, you can speed up the drying by putting them into an oven on the lowest temperature for about 45 minutes and then dry out naturally for the next 2 days or so. Ultimate Small Garage Clock Shop Once dried, they shrink and deform into weird and scary looking faces. Says Angie Maroevich, “You don’t have to spend a fortune on commercial Halloween supplies to have a great party.

The subfloor provides a stable layer - basically a sheet of plywood - for your floor to sit on. You’ll see a lot of van build videos on Youtube showing a ¾” subfloor, but that thickness just isn’t necessary in a van. The thicker the subfloor, the higher the cost and weight, and the more valuable interior space it takes away. We recommend using ¼” plywood for your subfloor, which is plenty thick enough for a van.
First, decide what your budget is and start searching right away! Even if you're not able to purchase a van right now, knowing the market and how quickly things sell is helpful. Get an idea of makes and models you like, and you'll also start to understand what is a good price for a van in your area. Each country, region and city is a bit different.

My plugs share breakers. I have them split up so there are no more than 2-3 receptacles on a single breaker. Ideally, each plug would indeed have its own breaker. But in a one-man shop where only one tool will be used at a time, I thought it would be more efficient and cost-effective to consolidate a bit. But the dust collector is on its own circuit since that will always run concurrently with other tools.
I am working hard (or hardly working) on our master bathroom vanity! I spent the whole day in the garage on Monday, but it was such a mess from all the other projects I have been working on, so I spent the day cleaning and organizing instead of building. Now I have a place to build the vanity and this coming week there is nothing going on so I will also have time. I can almost smell the progress!

If you’ve spent time at your local flea or farmers’ market over the last few years, you may have noticed the explosion that has taken place in the number of innovative small business concepts. From cool new clothing lines to ingenious fusion foods, the sheer diversity of the ideas on display really hammers home one of the key lessons when starting a small business: You need to find your key differentiator. For some this is their brand story, for others it’s the value of their service, but for many quick service restaurants and small retailers, it’s a distinctive core product line that demands the attention and interest of your customers.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.

The standard option for a shop floor is a concrete slab. You’re probably not going to go to the trouble of creating a basement beneath your shop, although it is possible. The weight of most woodworking machines suggests that a con­crete floor is the most solid and durable substrate available. It has the potential to be used as thermal mass to store heat from your heating system or from the sun, but it can be tiring and hard on your body to be standing on concrete all the time. You can add a vapour barrier, 2x4 sleepers and a wooden floor above the concrete to ease the tendency of the floor to strain your feet and back, or you can add anti-fatigue mats in key areas where you’ll be standing for longer periods.


Hey Ted! If you mean to ask whether you could sit up from one of the vertical sidebins and have enough headroom under the Leer 122, I think that would be a no. You’d have to build the sidebins to be a little shorter. At least with my truck, that would be the case. Perhaps with a full-size pickup you would have enough room thanks to the overall size increase of the canopy as well.
Another option to consider is an expensive but efficient Festool dust extractor. These dust extractors are designed to work with other Festool tools, but they also match up with most other brands' compact power tools as well. A nice thing about Festool's vacs is that the hoses dock neatly inside the units. There's almost nothing I value more for a compact shop than self-contained storage.
Chances are if you’re starting a new small business, you’re not afraid of a little risk. However, it’s also highly likely that you have invested a large amount of money in this new endeavor. It is only prudent to take sensible steps to minimize the impact of unexpected events, like the untimely death of a business partner, a lawsuit from a customer or employee, or a freak accident of nature.
The idea of not having your own bathroom nearby can be incredibly intimidating, but we’ve found that this is actually one of the easiest parts of vanlife. Public restrooms are plentiful throughout North America, and we’ve never not had a bathroom when we needed one. Gas stations, truck stops, Walmarts, McDonald’s - you name it, we’ve done some business there.

You can typically find paneling in pine and cedar. Pine is cheapest, looks fine, and will do the job. Cedar is more expensive, but it looks and smells awesome - and it’s resistant to mold and mildew. Paneling comes in different thicknesses, but we recommend using ¼” (5/16”). Thinner paneling weighs less, costs less, takes away less interior space, and will bend with your van’s contours.

Hey Ted! If you mean to ask whether you could sit up from one of the vertical sidebins and have enough headroom under the Leer 122, I think that would be a no. You’d have to build the sidebins to be a little shorter. At least with my truck, that would be the case. Perhaps with a full-size pickup you would have enough room thanks to the overall size increase of the canopy as well.
×