However, Sprinters are a lot more expensive than other options. It can be tough to find anything reasonably priced with less than 200,000 miles. For the Mercedes Sprinters, parts are more expensive and it may be difficult to find mechanics that have experience working on them (this is less of an issue with Transits and Promasters). And, since these are complex vehicles, they don’t lend quite as well to tinkering as something classic like a VW Vanagon or old Ford Econoline.
Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
Apps in this scenario would be able to fully function without any sort of network connection. Historically, examples of standalone apps might be your settings app or the camera app that comes with your device. Even today though, those apps usually have some interaction with the network. For example, you can share a photo from your camera via messaging.
The more outlets the better! I have a good mix of 220v and 110v outlets throughout the shop. I even included a few in the ceiling and the floor in hopes of avoiding power cords in the walkways. And although this contradicts my previous comments about over-committing, I picked locations that would likely work for various tool configurations. If at some point they don’t work for my setup, I just won’t use them.
Other important power tools—A good jigsaw will help get you through many tasks, particularly cutting curves, that would otherwise require a bandsaw. Look for one with blade guides that keep blade deflection to a minimum. A handheld drill is also essential. A quality corded drill is much less expensive than a cordless one, and will never leave you without a charge. Also look for a quality random-orbit sander with a provision for dust collection.
If you want to operate your business under anything other than your own personal name, you’ll need to register your chosen ‘fictitious’ name with the appropriate county or state authority, otherwise known as registering your “Doing Business As” (DBA) name. The correct filing authority varies state-to-state. The Small Business Administration (SBA) provides a helpful tool to help you find the relevant authority for your state.

Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.
Reflectix only works if there is an air gap next to it - Reflectix themselves recommend at least a ¾” gap between their material and the area to be insulated. This is the case because Reflectix is a radiant heat barrier, and when you put it right up against your van walls the foil cannot reflect back radiant heat (remember, radiant heat is only transmitted through air or a vacuum). If there is not an air gap, the insulating power of Reflectix is very low.
It all depends on what you care about most. Putting your kitchen by the side door could simplify refilling your water and propane tanks. Putting it behind the driver’s seat creates a nice, open feel in your van. Right behind the cab makes your van more private, while all the way in the back is a different twist on most van layouts out there. Some vanlifers even have kitchens that pull out of the trunk on drawers for cooking outside.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Gone are the days when you could apply for a building permit based on a sketch on the back of a cigarette pack­age. In provinces like Ontario, design work must be undertaken by an insured designer registered under the provin­cial building code or by the owner of the property. You can do the drawings as the owner if you can demonstrate effec­tively through your drawings that your structure will comply with the techni­cal requirements of the building code in a clear and concise way. You will be required to submit detailed drawings, including the following:

Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).


The standard option for a shop floor is a concrete slab. You’re probably not going to go to the trouble of creating a basement beneath your shop, although it is possible. The weight of most woodworking machines suggests that a con­crete floor is the most solid and durable substrate available. It has the potential to be used as thermal mass to store heat from your heating system or from the sun, but it can be tiring and hard on your body to be standing on concrete all the time. You can add a vapour barrier, 2x4 sleepers and a wooden floor above the concrete to ease the tendency of the floor to strain your feet and back, or you can add anti-fatigue mats in key areas where you’ll be standing for longer periods.
The enormous range and affordability of options has provided the chance for small business owners to apply technology to their accounting, marketing, and day-to-day operations. You can spend less money, save valuable time, and gather data about almost every aspect of your business. What’s more, you can enhance the way your customers experience your store in a meaningful and cost-effective way.
Wide aisles also prevent the dreaded butt brush, a term coined by top retail consultant Paco Underhill. His studies show that both women and men avoid tight or crowded aisles where they might brush bottoms with other shoppers. Really, this is a thing! Learn more about Paco’s retail research and insights in his book, Why We Buy: The Science of Shopping.
I used to coat my metal table saw and planer bed with auto wax because it makes the wood slide nicely across the metal. But then I saw an expert cabinetmaker use wax paper, and now I do the same. I keep a roll in my shop drawer and rub a sheet of it over the metal beds on my table saw, router, planer and disc sander. The wax coating doesn’t last as long as a good paste wax, but boy, is it a lot easier and quicker. — R.J. Hayes. Plus: 22 clever new uses for your tools.
This style of saw will provide more power than a contractor-type saw and have the high-quality rip fence you need to do good work. However, because they are favored by professionals and serious amateurs, cabinet saws are harder to find on the used market. Scour the classifieds and online sales (be sure to check industrial auction sites as well), and do some networking. Check the bulletin board at your hardwood supplier and ask the proprietors if they know of anyone selling a saw. Also call local cabinet shops. They sometimes have a surplus tool sitting idle that they’d be willing to sell. Take your time in this step. A careful investment will pay dividends in the long run, but a well-intentioned compromise can cause long-term frustration.
A loop floor plan, sometimes called a racetrack layout, creates the most guided shopping experience of the three. A loop store layout features a defined pathway throughout the store, which exposes customers to every item on display. Bed, Bath & Beyond stores are good examples of a loop floor plan. Loop floor plans work very well with zone merchandising tactics, too, which we discuss in detail below.

With all the time and effort you've put into properly merchandising your products, the last thing you want is for incoming customers to hurry past them — this ultimately limits the number of products they'll purchase. One way retailers combat this is through creating breaks that force them to pause. These are sometimes referred to as "speed bumps." Essentially, this can be anything that gives customers a visual break and can be achieved through signage or special/seasonal displays.
Do you want to create the next great retail dynasty? Do you want to be Abe Froman, the Sausage King of Chicago? Or are you just looking for a simple local lifestyle business? Are you hoping to create a franchise model? Or do you see your local business as a testing ground for an ecommerce business? Your end goal will clearly inform your decisions, so it’s worth considering what it is early on.
By building your own workshop machines and jigs, you can create customized tools that include all of your favorite and much-needed features for less than half the cost of commercial tools (plus, get bragging rights for having the coolest woodworking shop in town). All you will need is a drill press, table saw, some common tools, and patience. Then, you can start following these step-by-step instructions to create homemade machines such as a sliding-top router table, jigsaw, downdraft dust collection table, a 24” band saw and more!
Let's talk about a few strategies for building out your shop below retail price.  There are the obvious ones like yard sales, craigslist, estate sales, and thrift stores, however, these can be hit or miss.  First of all, not everyone lives in an area where these avenues exist.  Second, when your brand new to woodworking, it can be hard to evaluate a tool that your buying second hand.  Because of this, I'm not going to focus on these channels in this post, but I will say, if your willing to do some hunting for second hand tools, you can easily save 50% to 75% on some perfectly fine equipment.
Tight control of inventory, while not a particularly glamorous part of owning a small business, is therefore one of the most important ways you can impact profitability. The good news now is that there is an array of technology available that can make this whole process much smoother, including sophisticated forecasting tools that will help you predict your required inventory levels for each day based on past sales, weather records, and many other factors.
Find out what tools you need and how to budget for shop setup. Whether you are going to be doing furniture, cabinetry or woodturning, this workshop tools list and budgeting guide can help. Learn how to prioritize purchases of shop tools based on space, interests and cost. Check out a comparison of the workshop tools you can get for $4000 vs. $10,000 and determine how much you need to spend for the shop you want.
I framed in a 4x8 Garden Shed on the back.  I didn't want it so deep that stuff would get buried in it.  I need to take an updated picture of the back.  These pics were from early on and I have changed some things in the organization.  I used similar framing techniques and built a lean to roof attached with metal hangers.  I chose to use clear corrugated roofing to allow natural light into this shed.  You can see the 2 shopvacs that were originally part of my simple vacuum system.  I have removed them and found that I get better airflow using an electric leaf blower with the vacuum attachment hooked up to my system.  There is a large metal trashcan with a dust collection separator to collect the larger pieces of saw dust and chips.  My air compressor is on a shelf on the right now and I ran a hose through the wall and to a 25 foot reel attached to the ceiling.  I wired separate switched for both on the inside of my shop.  These systems work extremely well for a small shop.  The wall provides some insulation from the overwhelming noise they would otherwise create inside the shop.
“Every time I’m choosing a new a location, I head down there with a big flask of coffee and a clicker to count all the people that walk past. Then I walk to the nearest public transportation at rush hour and look at how people are heading home. I turned down one location because while it was right next to the subway, I noticed all the commuters were coming out of the other subway entrance. It turns out all the residences in that area were on the other side of the street.” —ShopKeep Founder and Experienced Small Business Owner
When starting your small business, the easiest way to go about choosing a business name is to approach the task the same way you approach building new relationships. Did we lose you for a second? Here’s what we mean. It takes just one-tenth of a second for us to judge someone based on a first impression. There are endless relationships that instantly blossom or never get off the ground based off of this one simple fact. Most of us, even if it is on a subconscious level, understand this. Which is why when we meet someone that we are trying to impress, we make an attempt to adjust our appearance, body language, even the way we talk, to ensure we are putting our best foot forward.
If you’re looking to setup a shop equipped mainly with stationary power tools, I’d focus the bulk of your budget on the primary big tools. It’s easier to come up with $10 for a couple of clamps as an impulse purchase, than it is $1000 for a good table saw (TS). Most shops feature the TS, and that’s where I’d focus the bulk of my research and budget, unless you’ll primarily be using a band saw (BS). The biggies for me would be a good full size stationary table saw, planer, jointer, router and router table, and maybe a modest DC (like the HF unit for $150). With those main tools, you can build just alot using dimensional lumber or sheetgoods. A BS and DP are nice, but can be added down the road…in the meantime, a modest jigsaw and handheld power drill worked fine for early on. You’ll want a reasonable work surface, whether it’s a nice bench, or an old door. I’d add a good tape measure, squares, a chisel or two, sandpaper, and some basic clamps, then would add more clamps, block plane, and other extras as you go. (Ask family members for gift cards to Rockler, Woodcraft, Amazon, Lowes, HD, etc….). $3k is doable if you’re selective….the used market can be your friend if the right deals come along.
Before you bid in an online auction, check the site’s rules of operation. At some sites, a winning bid is a binding contract, which can be a problem if you can’t inspect the tool before you purchase it. Don’t forget shipping costs. In some cases they can exceed the cost of the tool. Also, make sure the tool you’re buying will run on the power you have in your shop. Many former industrial tools run on 240v single-phase power. If your shop doesn’t have 240v service, you’ll need to factor in the cost of upgrading before deciding to buy. You don’t want to saddle yourself with a tool you can’t use, no matter how good the price.
These could mean anything from a local sponsorship of a high school sports team, an infrequent advertisement in a local paper, an unusual purchase of artwork (such as mural or window art), or anything that doesn’t necessarily fall in the categories listed above.  Your total coffee shop costs will be broken down by one-time startup costs, fixed costs, and variable costs.
For the next step up in convenience, consider adding a dedicated beverage cooler to your workshop as well. Though many people set up an old refrigerator in the garage for extra soda and beer, a dedicated mini-fridge will help you save on electricity, since new models are far more efficient than old ones. You can pack your beverage cooler with your favorite soft drinks for a pick-me-up while you work or use it to store a lunch to enjoy on a break —all without tracking dirt and or grease into your clean kitchen.
Once you’ve planned the basic layout of your workshop and have added all the tools and speciality appliances you need, take a last look at the overall design to make it aesthetically pleasing. Add overhead lighting for general illumination and task lighting over your work stations so you can see your project clearly. For maximum flexibility, you can mount clip-on work lights to nearby shelves and point them where you need them, knowing you’ll be able to move them about as required for different projects.
According to a recent digital marketing survey conducted by Clutch, 74%of small businesses surveyed had a company website. Of the businesses that said they do not have a website, 9% said they planned to build a website in the future, while 10% said that that they are unlikely to build one. One thing is clear, small business owners are starting to join the digital revolution and are reaping the rewards in terms of increased customer loyalty, growing word-of-mouth, and most importantly, increased sales.
For example, at a certain point, you will be asked to project how much cash you’ll spend in your fifth year of business. You’ll think, “Are you kidding? I haven’t even opened my doors yet and you want me to describe what my expenses and revenue will be like in five years?” Well, the quick answer is yes. Nobody ever said that starting a small business would be an easy feat.
Conduction is heat transferred across solid surfaces- think touching a hot stove. It’s also how heat gets out of your van in the winter. The heat inside your van is conducted through the solid surface of your walls and ceiling. Insulating the inside of your van will help prevent heat loss through conduction during the winter, and will also stop your van from conducting the sun’s heat inside during the summer.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
On-demand apps incorporate many of the elements seen in apps with logins and social features. Like ecommerce apps, they also include a transactional component, because users need to purchase goods and services. Unlike social and ecommerce apps, however, on-demand apps essentially require two completely unique user experiences. For example, an Uber driver needs advanced mapping and routing functionality while a rider doesn't. Similarly, the driver doesn't need to do a payment while a rider does.

By setting up a separate legal entity, you limit the financial fallout from a failed business, you shield yourself from legal risks (such as someone injuring themselves in your store), and you potentially put yourself in a more advantageous tax situation. Equally, if you are working with partners, ensuring you are set up with the appropriate partnership will give all parties reassurance about their legal standing, obligations to, and expectations from the business in question.
After looking at a number of spaces that are available to lease, you may start to wonder whether it’s better to buy or lease commercial real estate. Of course, there are occasions when it might be better to purchase commercial real estate rather than leasing it. For example, if you buy a commercial space, you’ll take advantage of equity, depreciation, cash flow, and asset appreciation.

I’ll throw this suggestion out to you too – while a warm sleeping bag would be a good start, maybe a couple sheets of plywood to put over the truck bed with a tarp over that would provide you some extra protection from rain/snow and also trap in some body heat. You wouldn’t have to make them permanent and could just slide the wood into the bed when not sleeping under it. A cheap bivy as Ryan suggested would also be a good consideration and a quality sleeping pad to provide some warm rating and comfort from the truck bed.


It almost goes without saying that everything about your shop's design should project the right answers to each of these questions. But in today’s market, you have to go one step further. In our digitally connected world consumers have seen it all. The true art of compelling store design is in telling a story about your business, while simultaneously anticipating the needs of your customers. It’s all about the surprise and the delight.
I could not consider a 12" jointer, given that the equipment had to be moved down the stairs to my basement, and the cost would blow my budget. What I wanted in an 8" jointer was true tables, a fence that is solid and easy to adjust, a cut depth gauge that is reliable, and long tables that aid in flat­tening longer bowed planks. I have found that the Taiwanese tools have come a long way in the past 20 years. I purchased the King KC-80FX 8-inch jointer, with lever adjust parallelo­gram tables. The system arrived in a good state of tune, and the well-written manual includes a full parts list and exploded parts diagrams. The tables were extremely heavy; more about getting things down the stairs later. The jointer is reasonably priced, it runs smoothly and it is well made.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Shops have value on many different levels. There is the sat­isfaction of having a place to create and work on projects that is hard to quantify, but definitely improves your quality of life. There is the value to your small business of having space in which to work wood and thereby generate income. There is the dollar value of the build itself, which will be a consider­able investment and, finally, there is the resale value of your property after you’ve added your shop. Before you go too far, though, it’s worth asking a local real-estate agent about the potential return on your investment in your area; generally shops won’t add significantly to the value of your property, so it’s worth thinking carefully about what else the space could be used for if you were to sell. The decision about whether it is worth it to build is a matter of balancing all these factors: projected sales balanced against the cost; the cost of build­ing is balanced against what it will be worth when you sell. Woodworking can be a creative outlet, can give you a sense of mastery, and even be a way to give back to your community by donating beautiful pieces to local charities for fundraising auctions, or creating pieces that future gener­ations will inherit. Ultimately, the value of a shop might come down to the emotional and social returns that it will pay you and the people around you for years to come.

Whether you end up looking at self-checkout counters, fancy lighting systems, special refrigerated cases, or any of a countless number of options, never forget that these are only tools to help accomplish your main goal. Your store needs to create an environment where customers want to be, where they feel comfortable and appreciated, and where that experience will prompt them to purchase (and hopefully encourage their friends to do the same). Equipment and technology decisions should always be made with your customers in mind.
For the large square windows near the tailgate I just used those big “magic auto shades” like these, which fit perfectly to cover up those side windows and the back window by the tailgate (I had four in the canopy) and another set up in the cab for my actual window. As for the longer side windows I just used a USPS box, haphazardly stuck up against the window. Nothing fancy.
If you’ve been to gem shows, you know how overwhelming and daunting they can be. Although it’s difficult to narrow down all those tempting options, your jewelry business profit margin will be greater if you plan ahead and focus on shopping for a particular line and color scheme of jewelry. Ultimate Small Shop Online Review You must keep the bigger picture in mind and try to keep your emotions out of the design process. Here are some tips for defining your market and researching it so that you can walk in and out of a gemstone show feeling confident in the business investments you’ve just made. Gemstone shows and fairs are marketplaces for vendors of gemstones, findings, jewelry supplies, and tools. Due to a large amount of competition between the vendors, prices tend to be competitive. I’ve found unbelievable deals on high-quality gemstones and findings at gem shows. To find gem shows near you, you can simply do a Google search for “gemstone show” or “gem fair”. Other sources of information are your local convention and visitors’ bureau and any lapidary clubs in your area. Anyone can attend most gemstone shows. Although you don’t usually need a wholesale license to get in, some vendors may ask for your resale permit before letting you buy at wholesale prices. Show admission fees tend to be in the $5 to $10 dollar range. What market are you trying to target with your jewelry? Don’t try to please everyone. Ultimate Small Shop does it really work Are you trying to appeal to individuals like yourself? What age bracket are you trying to reach? Does your jewelry line appeal to funky or traditional individuals? Next, take a trip to your local department store and take note of the colors that are being used for the upcoming season. Look at the jewelry and observe the lengths of the earrings/necklaces, the sizes of the stones, and the other various style elements for the season. While your designs should not be copies or replicas of the jewelry in the stores, you can simply incorporate the observations you make into your own original design ideas. Fashion and jewelry magazines are also a great place to find out what trends are coming into the stores. There will be an overwhelming array of gemstones and supplies at the show. Having a jewelry line style and color scheme in mind will allow you to narrow your focus. Vendors will offer gemstones in more shapes, sizes, cuts, and colors than you can imagine. Stick to the colors you’ve mapped out for yourself and walk through the entire gem show once before buying anything. Jot down and compare the prices of items that you’re interested in. Then take a break, go outside for some fresh air, and reflect on the items you saw and really liked. Then review your budget and the jewelry line you have in mind before returning into the gemstone show. Ultimate Small Shop Guide Download This will help you get the best deals on the items you’re most interested in so that you don’t blow your budget or become overwhelmed by the options. Soaring through the air, watching the clouds and the birds fly by.

We have a 5-gallon clear plastic Hedpak container that our sink drains straight down into. We really like this container because it’s clear, which means we can easily see how full it is. With 5 gallons of gray water capacity, we only need to empty it every 3-4 days. Dumping is easy - just remove the tank from under the sink and pour it out into an RV dump facility or other approved area.

×