In the summer months, your windows will be one of the primary ways that heat gets into your van. Because of its reflectivity, Reflectix works great as a window covering to reflect radiant heat away from your windows. And, if you’re concerned about height in your van, layering Reflectix under your subfloor is a good way to add a little insulation (R-1.1) without sacrificing headroom.
Before you bid in an online auction, check the site’s rules of operation. At some sites, a winning bid is a binding contract, which can be a problem if you can’t inspect the tool before you purchase it. Don’t forget shipping costs. In some cases they can exceed the cost of the tool. Also, make sure the tool you’re buying will run on the power you have in your shop. Many former industrial tools run on 240v single-phase power. If your shop doesn’t have 240v service, you’ll need to factor in the cost of upgrading before deciding to buy. You don’t want to saddle yourself with a tool you can’t use, no matter how good the price.
Alternately, a detached shop can often be located closer to your property line and offers you a bit more freedom in terms of the type of foundation you can use. It may give you a sense of welcome separation from your home and open up yard space or allow a deck on the back of your house that would otherwise be lost behind your shop. In an urban setting, if you would like to have a wood stove in your shop you may find it more challenging to find an insurance carrier that allows one in an outbuilding. Also, outbuildings can be subject to more stringent height regulations than additions.
Hello! My name is Donna Jean. I love to read books and my job is to write a daily review of all the novelties in the world of eBooks. I allow only the best of them to be published on my website. I really hope to make our world more bright, beautiful and kind. You can participate by downloading any book from my site, and you will receive health, luck, kindness, and love, which will support you during all your life. Wishing your dreams begin to come true, and every tomorrow be happy for you. Thank you! ❤❤❤
Note: Some of the links to products that we recommend on this page are affiliate links. This means that if you click through one of our links and buy something, we get a small commission at no cost to you. This helps us keep this blog going so we can continue to provide you with van build tips, tricks, and guides. We believe in honest opinions, and we never recommend anything we don't know about. Every recommended product on this page we've either used personally, have personal experience with, or have researched heavily.
To mark your cut for the bottom angle on the speaker stand legs, lay the board assembly on the plywood template again, and use the plywood edge to scribe the non-angled end of the board assembly. Be sure to consider which wood species (light or dark) you want on the inside and outside of your finished speaker stand legs, and keep that in mind when making your angle cuts.
WOW that is a nice size shop! I am looking forward to more videos on the shop projects! We have been shopping for a house for over a year & have finally found one but it has nothing for me to use as my woodshop! I currently have a basement shop that’s 24×40 & it’s really huge for me I couldn’t imagine any bigger. Anyway I will be looking at building a new woodshop for myself (yes I am a female woodworker) & you have given me lots of great ideas so far. I am an Artist & wood is my preference, everything I make is quite small (no furniture or anything that big) but I have lots of specialty tools for what I do as well! Thank you for sharing your ideas & all that you do. Keep up the great work!
This sturdy 30-in. x 6-ft.-long DIY workbench is the ultimate in simplicity. It’s made from only fifteen 8-ft.-long 2x4s and one sheet of 1/2-in. plywood. Learn how to build a workbench by following the cutting diagrams to cut the parts: Figure B to cut the plywood tops, then Figure C to cut all the framing. Use the lengths provided in the Cutting List (see Additional Information below). You can either screw the framing together with 3-in. screws or hand- or power-nail it together with 3-in. nails. Screw the plywood down with 1-5/8-in. screws.

5. Move beyond shelving. Shelving can be a very effective way to make the most of your wall space, but you can also find more creative, space-saving ways to display products. Instead of a big floor case for jewelry and other small items, Langdon recommends buying an old painting in an ornate frame and stretching the canvas in linen to create a giant corkboard to pin products on. At Poppyseeds, tea towels are displayed on an antique wrought iron headboard propped against a wall. The headboard takes up little space and adds character to the store.
Another flexible option is the portable work tables the guys are building back in our shop. This gives us a work surface that we can move wherever we may need it. Now the main workbench we’ve left a little gap between two of the cabinets for a trashcan or a stool to slip in but we did need to support the countertop where it crosses so Tim and Chris are adding some 1x4s to bridge the space. They’re also putting in a 2×4 inside one of the cabinets where the two pieces of plywood will have to be seamed. Then it’s just a matter of laying in the pieces in place and nailing them down to the cabinet. That trim strip around the edge is mostly for looks but the cedar backsplash along the back will keep us from banging up the wall or getting small items stuck between it and the counter. All in all it started to look pretty good.
I want the shop to be big! Not only do I have a lot of tools, but I tend to frequently bring tools in for testing. As you probably know by now, I also do a lot of filming. So I need a space big enough to allow for full movement around most of the tools. My tripod has a pretty good-sized footprint and having more room allows me to get the best vantage point possible. More space will also allow me to stage larger pieces of furniture, whether for the show or for jobs I take on locally.
SBA provides support and tools to aspiring small business owners and in particular to minority-owned, women-owned, disadvantaged, and veteran-owned businesses, including a government-backed financing scheme to qualified participants. Local and state authorities also have a range of programs designed to encourage the growth of your small business. Make sure to research your local authority’s website.
From building websites for other small businesses to providing technical support for certain projects, quality web development is in high demand right now. With such a technical skillset, make sure you can describe what you do and how you will do it in easy-to-understand language. Test your messaging on friends and family who don’t have a firm understanding of the work you do.
Once I had the walls completely filled in and trimmed out, I built my doors.  I clamped them in place each day until after I painted.  Then I installed the hinges and hardware.  I decided to change my original plan of building a hinged 4 foot door.  I was worried that the weight of it would cause it to sag over time.  I had also decided at this point to install a small unused AC in the back wall.  I thought that by keeping one of the doors closed, I could keep more cold air in during the hot summers.
Again, it is the inspiration I have (hopefully) given my son. To never be afraid to try, even at the risk of failure. If you don’t have all the answers, go with the knowledge you do have and trust everything else will fall into place. I am no millionaire; I have entered into a lifetime of debt because of what I’ve done with this build. And I’m going to try and keep it on the road as long as I can. I am not getting any help from Hasbro and Paramount Pictures, so I am looking for help with sponsorships.
A great supplier will provide the raw ingredients of your success — often literally. What’s more, they’ll deliver them on time, every time. And they’ll always deliver exactly what you ordered, no more, and no less. A large part of the process of inventory control is ensuring that you are paying for exactly the inventory that comes through your door, and not a penny more. Even great suppliers, however, are looking for the highest price possible for their goods, so once you find them, make sure you’re ready to negotiate!
Most businesses must obtain a variety of business licenses, permits, and registrations before opening their doors to the public. As a small business owner, it is your responsibility to ensure that you are abiding all the laws and regulations applicable in your state and to your particular industry. You also have to research and apply for all relevant permits and licenses that apply to your business type and location. Remember, it is impossible to plead ignorance as a defense. It’s up to you to educate yourself. When in doubt leave it to the professionals. CT Corporation offers custom license packages that simplify the process for business owners. Click here for an example of what that looks like.
Do you create, collect, or curate anything special? Consider starting an ecommerce store and turning your hobby into a full-time job. Whether you need somewhere to sell all that pottery you’ve been making, or an excuse to search for the sports memorabilia you love tracking down -- an ecommerce store can make it financially viable for you to pursue your passion.
Yeah, ventilation can definitely be a problem… I’ve just got one window with a screen on it if bugs are an issue–though I haven’t camped in too many areas where they are truly horrendous. Normally I just sleep with the windows/door open to let airflow. I’ve seen some more industrious folks even put in the rooftop fans on their truck camping rigs. Pretty elaborate and beyond my pay grade, but worth searching expedition portal. I like the mesh fly idea if I happen to travel to buggy areas again. Cheers!
If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.
One site that I found a year or more ago was Life Remotely. They converted their truck to accomodate 3 people traveling from Seatle to the end of South America. They camped in tents most nights and some hotels/hostels but did a lot of conversions to their truck. Plus they blogged the whole time which is pretty cool if you want to take the road trip international.
For years my wife and I had agreed that we would one day leave Oklahoma for someplace we really loved. That day finally arrived last year when we found a home in Vancouver, Washington that met our dreams. Only thing missing was someplace for a woodshop. Well, there was a place, under a deck, but not a room. So, as part of the move we had a local contractor build a room that would one day be the wood shop. Fortunately there was already a door from the house into this area, and about half of the “walls” were there, in the form of concrete retaining walls.
At some point in the process of starting a small business, it’s pretty much guaranteed that you will hear the following statistics (or variations thereof): 25% of new small businesses close their doors within the first year and 60% are gone within three years. The exact numbers here may vary, but the message is all the same: be afraid, be very afraid!
The beauty of a portable A/C unit is that you don’t have to heft it into a window and block off a valuable source of fresh air for keeping paint fumes at bay. Instead, choose a model with a low profile that you can tuck under a table or against a wall when not in use — a model with casters for maximum maneuverability is ideal. Choose a high-powered unit that will condition at least 400 square feet of space and move it where you need it for maximum comfort as you work.

With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Hey Marc. Just wanted to send a huge congrats your way for this milestone. It’s been pretty awesome to follow you on this journey since I discovered you on iTunes some 5 or 6 years ago. Mad props for what you’ve done to grow and enhance the online woodworking community as well as woodworking as a whole. I think with todays generation (as well as future generations) growing up behind a computer, the work that you and the rest of the podcasting world do will go a long way towards bringing new people into the craft. I hope that in the future you are able to start a series of videos showing how you introduce Mateao to the craft. Keep up the awesome work!
Ideally, the stands should lift the speakers to roughly ear level of a sitting person. This is important because it aligns the ​subwoofers and tweeters relative to the ear and achieves the best balance of sound. The high frequencies are often missed when speakers are placed too high or too low. Speakers placed on a shelf or table often cause the surface to vibrate, thus distorting bass. These speaker stands isolate the speaker's vibrations from the floor, allowing you to hear the bass from the speaker and not the vibrations from a shelf, table or floor. Speakers come in various sizes and shapes, so the height of your speaker stands is dependent on your unique speakers. For this project, we give you the dimensions suited for the speakers shown in the photo, but you can alter the design to fit your individual needs.
As you can imagine, this collective overflow of dare we say, lack of imagination, has resulted in a surplus of duplicate business names across the country. This wasn’t necessarily an issue until the internet came along. The introduction of the World Wide Web has left small business owners from all over the world competing for the same digital real estate: www.tonyshardware.com, facebook.com/tonyshardware, @tonyshardware and more.
It looks great. Your little guy looks like he's having fun. I just had over 50 kids come through my shop last weekend to do some woodworking for cub scouts. I am saving left over insulation to put in there soon. I restocked my plywood recently too. The pieces of pipe made it much easier to pack in a lot of heavy pieces. I also took the time to measure lengths and mark the ends of all my lumber in the hatch under my bench to find what I need a little easier. My $100 8x8 needs a little TLC soon. But the shop is still rock solid. If you plan on making a lot of dust, I would also suggest a diy air filter with a box fan and a cheap air filter. It helps a little.
A warning out of concern and love for my fellow 'ablers. A framing nailer is a VERY dangerous tool. Not something to loan out willy-nilly to just anybody. For a small project like this it's just not going to save a lot of time. Most of us are better off burning the extra calories that swinging a hammer uses anyhow. Emergency rooms are seeing a lot of visits because a lot of guys see these on TV and at your big box stores and think they look cool. They are only marginally safer than shooting at the nails with a pistol. (Hmmm...). Be careful, PLEASE.
There seems to be two things I like looking at and they are work benches & work shops. I too use my work shop for several other activities. I currently have a basement shop with a walk out entry, which is roughly 340 square feet and shaped like a flat s and has less than 8' ceiling height. In that shop I have an old Unisaw w/50"fence, 8" jointer, 15" planer, 10" sliding compound saw, 14" bandsaw and various & assorted power & hand tools. Also in the same space I have a small closet, dog grooming tub, & a space where a bathroom was roughed out. It is far from finished space and I have plans to put up a ship lapped paneled walls and fix up the closet for tool storage. I also plan on putting a cyclone in the bathroom space along with a tolet. I can work in the space as it is pretty well but the studded walls, insulation, & dust make the space somewhat uninviting.
A good portable air conditioner will also remove excess water from the air, which is critical for keeping your stockpile of wood in good shape. Lumber should be stored in dry conditions so it doesn’t warp, so look for efficiency features that allow you to run the unit overnight in the summer as needed —without worrying about blowing up your electricity bills. Other good features to consider include a thermostat and variable settings that allow you to set your workshop temperature to the perfect level for your comfort.
The small apparel boutique pictured above really nails these traffic flow details! A roomy entrance offers clear sight and travel lines to eye-catching power walls on the right, and an inviting seating area towards the back. These lure customers into the store with the promise of treasures and comfort within. The shop even has a left-side checkout midway back. Someone really did their customer behavior homework on this retail store layout.
If you’ve spent time at your local flea or farmers’ market over the last few years, you may have noticed the explosion that has taken place in the number of innovative small business concepts. From cool new clothing lines to ingenious fusion foods, the sheer diversity of the ideas on display really hammers home one of the key lessons when starting a small business: You need to find your key differentiator. For some this is their brand story, for others it’s the value of their service, but for many quick service restaurants and small retailers, it’s a distinctive core product line that demands the attention and interest of your customers.
Chris Marshall: You’re asking a question that would take many magazine articles or a whole chapter of a good shop-design book to answer adequately. If you haven’t already done so, you might also want to ask this question to the good folks that frequent our forum on woodworking.com. Every woodworker with a shop will have a slightly different answer, so here’s mine. I’ve never had a brick shop, but my last one was a metal pole barn (30 ft. x 40 ft.). I outfitted the interior with 2×6-framed walls and plenty of insulation. It stayed reasonably cool in the summer and warm in the winter, using a wall air conditioner and a 60,000 BTU furnace. Currently, I have a 24 ft. x 42 ft. garage space for my shop. It is framed conventionally with 2×6 walls and stick-built 2×10 rafters. I’ve only been in my new shop for about a year, but it is working just as well or better than my pole barn did, because the new shop has many large windows that let in lots more natural light. I’ve used 8-ft. fluorescent T8 light fixtures in both buildings with good success, and I ran both 110- and 220-volt outlets all around the room. The last shop had a plywood floor; the current one, a concrete slab. I thought I would notice a bigger difference between the two flooring types, in terms of how tired it makes my legs by the end of the day. But in all honesty, a good pair of supportive shoes seems to make the difference moot for me. Both types of buildings benefit from a dehumidifier during humid months (when I’m not running the A/C, that is) to keep the relative humidity low and my tools rust-free. If all things were equal, and money were no object, I would probably go with a conventionally framed wood building over the pole barn. It was easier to build that from scratch as opposed to retrofitting the pole barn framing with walls afterward. But, as I say, the next woodworker will probably offer you a completely different answer from mine. Good luck in your decision!
Remember the social media networks we asked you to secure in section five, Choosing a Business Name? Well, now is the perfect time to activate those channels. Use social media to build excitement about your grand opening and keep potential customers informed about special promotions and sales. People want to know what makes you special, so tell them why your store or restaurant will be different to what is currently available. From sharing pictures of that new fancy espresso machine or sneak peeks of your store’s interior, you can gain buy-in to your central message and build some anticipation before you even open your doors. Knowing how to to leverage key social channels is imperative to starting a success small business that will stand the test of time.
Of course, if you’re going to build a sweet shop, you’re going to have to outfit it with an equally sweet bench. This afternoon I stumbled upon a UK bench-maker by the name of Richard Maguire. Built of kild-dried ash, Maguire’s benches are then finished with an oil and wax combination and feature twin screw vises which, while really interesting, might not be a perfect fit for everyone. While you can use these vises to apply more accurately distribute clamping pressure on different-sized stock, I could certainly see it becoming a wee bit of a pain when clamping stock that comes in contact with the entire length of the vise’s face. Having to equally screw in each side might frustrate some woodworkers. Still, these benches are a blast to look at.
To help, I’ve pulled together 40 small business ideas for anyone who wants to run their own business. Use these as a jumping off point to spark your own unique ideas.And if all else fails, live the words of Airbnb Co-founder Brian Chesky: “If we tried to think of a good idea, we wouldn’t have been able to think of a good idea. You just have to find the solution for a problem in your own life.”
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
×