A warning out of concern and love for my fellow 'ablers. A framing nailer is a VERY dangerous tool. Not something to loan out willy-nilly to just anybody. For a small project like this it's just not going to save a lot of time. Most of us are better off burning the extra calories that swinging a hammer uses anyhow. Emergency rooms are seeing a lot of visits because a lot of guys see these on TV and at your big box stores and think they look cool. They are only marginally safer than shooting at the nails with a pistol. (Hmmm...). Be careful, PLEASE.
My wife and I have just bought a block and will be building a new house – as part of this will be the building of the “shed” – which is really a workshop as I am a very keen Woodworker (I have most of the toys!!). My question is – Leaving money aside “Is a brick or metal shed better – especially in regards to moisture, inside temperature (heating and cooling), noise etc”? Any other suggestions would also be appreciated – eg lining the structure, power needs, lighting, etc. I appreciate your expert opinion. – Ivan Banks
Ventilation is extremely important in the rain. These window deflectors allow us to leave our front windows cracked while it’s raining, so we can pull in fresh air and create airflow with our vent fan. As a bonus, it also reduces annoying wind noise while driving on the highway. The Auto Ventshade is fairly inexpensive, easy to install, and makes a great addition to any van (make sure you get the correct one for your specific vehicle).
Many small business owners start on a shoestring budget, intertwining their personal and business finances, supporting the business with their personal credit cards, accepting payments into their personal checking account, and even submitting tax returns that mix up personal and business finances. While this is common, it can create tax headaches, make bookkeeping more time consuming, and, most importantly, can also interfere with the proper evaluation of your business.
We think that insulating your van’s floor is worth the minimal extra cost it adds to your build. The best floor insulation is ½” XPS foam board due to its high r-value per inch and its compressive strength. But a layer of Reflectix will add some insulation while taking away less headspace. We used Reflectix, but if we did it again we’d go with the foam board.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
You need an out-feed table to support work exiting the table saw and band saw. By placing the tools close together, I was able to make one out-feed table that works for both tools. I put four pivoting wheels on the table, allowing me to shift the table in any direction. By placing a shelf below the table, I gained some much needed storage space for portable power tools. Finally, since this is a large work surface, the table also serves as a true, flat assembly table.
When you set out to start your small business, investing in the right technology and equipment should be considered in conjunction with your store design. They should seamlessly integrate with and improve the customer experience in your store. Everyone remembers their first trip to the Apple Store and the “wow” moment of having their sale rung up by the assistant in the middle of the store, rather than having to wait in a line. But fewer people probably notice the carefully positioned heater that creates a warm environment for them as they walk through the door. It’s all part of the same idea.
Tight control of inventory, while not a particularly glamorous part of owning a small business, is therefore one of the most important ways you can impact profitability. The good news now is that there is an array of technology available that can make this whole process much smoother, including sophisticated forecasting tools that will help you predict your required inventory levels for each day based on past sales, weather records, and many other factors.
We don't have a Dometic CFX-50 in our van, but we wish we had gotten one for our build. This is a great little fridge that many vanlifers happily own. It’s rugged and durable, and it keeps your food cold for less money than many of the other fridges out there. It also has a nifty side-open lid, which makes it a lot easier to open with a lower clearance.
Aside from mechanical repairs, a mechanic’s toolset will help you loosen and tighten bolts - which you’ll need to do during the gutting process, installing your electrical system, and at many other points during your van build. This Crescent 170-piece tool set has all the essentials, including 6-point and 12-point sockets in ¼”, ⅜” and ½” - not to mention pliers, crescent wrenches and screwdrivers.
Overall I am very happy with the final results and I can’t wait to get back to making sawdust. The first project to be completed in the new shop is going to be a Queen Size Platform Bed for one of my favorite clients. I mentioned in a previous post that one of my goals this year was to get back into doing client work and this is me making good on that promise. I can’t wait to get started!
Sadly, that’s most of my power tools and shop accessories, but it’s a growing collection. Compared to all the money I’ve wasted on small electronics and computer junk in the past, I’d say this has been, and will continue to be, a much better investment. I just wish I had come to that realization back in college, when I was probably spending $500-$1000+ a year upgrading my computer.
Check your local papers, especially the free shoppers, for information about upcoming shows Another venue for craft retailing is at the local flea markets that spring up in every community just about every weekend. Again the entrance cost is usually minimal. Ultimate Small Shop Result The only other thing you need is a little marketing savvy. With little cost and some effort, you will be well on your way to knowing whether there is a market for your craft. Once you know that, you can move on and think about other ways of selling, such as in galleries, on consignment, on eBay or from your own website. Once you spend your precious time and energy creating a scrapbook, make sure it lasts! There are a few simple things you can easily do to ensure that your scrapbooks look just as good as the day you finished them, for years to come. The first thing to avoid is paper that is not lignin-free. You’ve probably heard that before, and it is true, but what is lignin anyways? Lignin is a stiff component of a plant that quite literally holds it together. Although lignin is necessary for plants and trees, you want nothing to do with it! After a while, lignin will cause photos, fabrics and other paper that touch it to turn brown. Yes, the lignin-free paper does cost more, but it is a vital part of preserving your cherished scrapbooks. If the paper is not lignin-free, it will eventually discolor your photos and other materials touching it. So when buying paper for your scrapbooking projects, be sure to look for packages that say “lignin-free,” because if it doesn’t say it, then it most likely isn’t.The fabric is a big concern for preserving your scrapbooks, but unfortunately, it is often overlooked. Many people assume that all fabrics are acid-free, but they aren’t. Silk actually goes through an acid bath during the manufacturing process, as well as many tie-dyed fabrics. This isn’t to discourage you from using it, not all. Just try to make sure that no photos directly touch fabric, and if you need them to overlap, make sure there is a layer of paper between the two. Another consideration when using fabrics is if the color will bleed off onto your page and other things touching it. To test for this, cut a square inch off and soak it in a glass of water overnight. If there is no color bleeding from it the next day, then there isn’t any risk to your scrapbook. But if you do see color in the water, or collecting at the bottom of the glass then don’t use that fabric in your scrapbook at all. When using glitter, be sure there is a top layer of spray adhesive to lock them down, or better yet use special glitter glue where the glitter is mixed right in. If this is not done right the glitter will slowly fall off, and loose glitter means scratched photos. After you have planned the layout for your photos, be sure that you are using the right kind of mounting tape for them! Regular mounting tape is fine for buttons and bottle caps, but when it comes to mounting photos you need to use special photo mounting tape which is completely acid-free. Ultimate Small Shop Member If you don’t, your photos will slowly discolor. The tape should say “acid-free” right on the packaging.
Reflectix only works if there is an air gap next to it - Reflectix themselves recommend at least a ¾” gap between their material and the area to be insulated. This is the case because Reflectix is a radiant heat barrier, and when you put it right up against your van walls the foil cannot reflect back radiant heat (remember, radiant heat is only transmitted through air or a vacuum). If there is not an air gap, the insulating power of Reflectix is very low.
Hey Brett! Awesome to hear that your own plans are coming together. I can’t really recall seeing any dirtbags rolling around in a Pruis… I wouldn’t imagine it to be the ideal vehicle for transporting gear and living out of, but the gas savings would really add up over 6-7 months on the road. In general, I’m in favor of going with what you’ve got and finding creative ways to make it work. Maybe you can add a rooftop box? On some vehicles, people even remove the passenger seat(s) for extra storage space. The biggest problem with the Prius that I see would be finding a place to sleep while you are on the road… But I guess that’s where your gas savings and cheap hotel would come in. I know Gina Begin has been living in her little car for a long while now, check out her stuff, and maybe reach out to her. She’s a veteran at dirtbaggin’ it in a car: http://www.ginabegin.com/2013/05/the-ultimate-guide-to-living-on-road-15.html
It's true for large and small shops alike: Sawdust and chips get everywhere when you use power tools. Small home-woodworking shops are often in shared rooms and may be poorly ventilated. And airborne sawdust and particulates linger for a while before settling. It's a bad combination for human lungs, which are not fond of sawdust, let alone the types of chemicals found in plywood and other engineered materials.
Does it motivate you? This is a tricky one because sometimes we have to do the work that we don't want to do to become successful. On the other hand, if it doesn't motivate you, you just literally wasted your time writing it down because you wont complete it. Consider your skill set and desire to want to work on that goal to help you eliminate goals (because you can't do everything).
For many new small business owners, the additional expense and bureaucratic hoopla involved in obtaining the correct paperwork often leaves them dragging their heels. This attitude, however, can result in stiff financial penalties, or worse, having your permission to do business revoked. Before we jump into the why and how of obtaining your business permit or license, it’s important for you to understand the difference.
Plywood comes in several different types, the most common being pine and lauan. We used ¼” lauan plywood for the walls in our van. Lauan is cheap, it bends easily, and in our opinion its grain pattern looks nicer than pine. Hardwood plywood like birch costs more than pine or lauan, it weighs more, and it’s more difficult to bend. This type of plywood is a great option for furniture, but we think lauan is a better choice for your walls and ceiling.
There are a number of woodworking fixtures you can get by without for a long while, but a sturdy workbench isn't one of them. The trouble is, those solid-hardwood benches we all lust after can completely blow a modest woodworking budget. Here's a bench that splits the difference. You'll get a top that can stand up to significant abuse, a sturdy, heavy base that keeps the bench planted where you put it, and an end vise and T-track system for holding workpieces as well as a variety of unique jigs. It may not look quite like a European bench, but it works just as hard as one for a lot less money.
Trademarking is a lot less expensive than most people think (although enforcement is another thing entirely), but make sure to do your research! If someone else is already using your proposed name, your application will be rejected right away and you will not only lose your application fee, but the time invested would have been in vain. And as you know, time equals money.
Great website! I spent a summer living out of a ford focus hatchback while road tripping around the United States. The rear seats were replaced with a small platform to store gear and the rear windows were tinted. I enjoyed the freedom that anywhere I parked no one would see me hop from the drivers seat to my platform for some zzz’s. Also no one would guess that someone is sleeping in a 3dr ford focus.
These basics are going to set you back about $180, leaving you with $320 left to work with. We are going to be leaving behind two hand powered tools from the $250 shop and upgrading to powered alternatives. This should lead to more consistent results, more enjoyable builds, and increased efficiency. These are all goods things that only the biggest fans of The Woodwright's Shop would argue with.
My enthusiasm was kindled and I made friends with Surrey Timbers for more 'exotic' wood. My next purchases were a Drill Press and a Scroll Saw from Axminster Tools and I set to work. An excellent piece of Yew followed by some Thermal Ash has so far produced 4 cribbage boards. I then obtained a Palm Router which, after some practice, I find better for the more intricate work.
At times, while you are starting a small business, it will seem like there is a brick wall in front of you, made up of all the different problems that will occupy your time and mind: a lack of funds, permits, regulations, tax worries, inventory issues, or a lack of customers. Concepts like “free time” and “the weekend” will take on a very different meaning. While the emotional ups and downs of cash flow management and customer service, may drain your will to live.
The final size I decided on was 1800 sq. ft. Yeah, that’s big! I actually balked and second guessed myself after we received the estimate from the contractor. Sure, more space is nice, but at what cost? I then asked for a second estimate, bringing the shop down to 1500 sq feet, which is still huge. As you might expect, the savings just weren’t that substantial. By the time you get over 1000 sq. ft., the price per sq. ft. is really low, making it very difficult to justify down-sizing. So I bit the bullet and stayed with my original choice of 1800 sq. ft.
A track saw, such as those by Festool and DeWalt, makes things even easier and offers greater accuracy, but these saws are also quite a bit costlier. With a circular saw, you have to keep the shoe pressed against a guide while pushing the saw forward. Track saws, on the other hand, pop onto their tracks and need only to be pushed forward. Track saws often feature splinter guards to help reduce tearout as well for smoother and straighter edges.
The Best Prices for Tools – Ralph shows you where to get the beast deals for the tools and equipment you need. You could buy them yourself from popular outlets like Home Depot, Lowe’s, and Amazon, but the Ultimate Small Shop guide shows you where to get these tools and equipment at cheaper prices. Of course, cheaper isn’t always better. These aren’t just cheap tools that are ineffective. Just good value for money on good tools.
With all the time and effort you've put into properly merchandising your products, the last thing you want is for incoming customers to hurry past them — this ultimately limits the number of products they'll purchase. One way retailers combat this is through creating breaks that force them to pause. These are sometimes referred to as "speed bumps." Essentially, this can be anything that gives customers a visual break and can be achieved through signage or special/seasonal displays.