Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
2) I haven’t spent very many nights in full on winter conditions (that 12 degree night in Boise comes to mind!), so I can’t comment too much. It was fine for that… Mostly it was hard transitioning from the warmth of the cab to the frigid air while you are shifting things around and getting ready for bed, but then once you were inside the canopy it was fine. Lots of frosty ice on the inside windows, but in my sleeping bag all was well. It stays a little warmer in the canopy. Maybe I’m a wuss, but I didn’t want to spend an extended period of time dirtbagging it in my truck while I was ice climbing (I spent the first two months in Ouray, CO, sharing a rental), I just thought it would be too challenging/miserable to dry and manage gear in a confined space with the shorter daylight hours. I’d be perfectly content doing future weekend trips with this setup though!
I bought an energy-saving outlet strip for my TV and its components. One outlet controls several other outlets on the strip, so when I turn off my TV, the adjacent controlled outlets for my VCR, DVD player and receiver sense that no current is going to the TV anymore, and those outlets shut off. Then I decided to try it out in the shop. I use it with my router table, disc sander and orbital sanders, so when I flip one of them on, my shop vacuum also starts up to take care of dust collection. It also has two outlets that are independent for other accessories you’d like on all the time. You can buy the outlet strips at amazon.com. One choice is the Belkin Conserve Socket with Energy Saving Outlet (about $30). — D. Linley. Plus: 30 more smart tips for working in your home shop.
Of all the LED lighting options, puck lights are the most difficult to install. You’ll have to run wiring behind the ceiling/walls for each light. And you’ll need to cut a hole with a hole saw to recess the lights into the ceiling. But with some preparation and care it's not too difficult. We have full instructions for installing LED puck lights in our epic electrical post.
Thankfully, the tools we use continue to get better and more app specific. For example, Sketch lets us design more efficiently with its focus on creating user interfaces. Marvel helps us craft better prototypes with it being specifically for apps. Swift has been a revelation for the Apple ecosystem and has expanded developer interest considerably. Android Studio and now Kotlin are doing the same for Android apps. Firebase and yes, even Parse, now as Parse Server, helps developers build app-focused backends to bring apps to the market more quickly.
I’m for using what you have got as well but if what you’ve got just really isn’t up to the job it doesn’t hurt to consider switching to something else. Not sure what year your Prius is but if it is fairly new I imagine you could sell it for much more than what an older reliable 4 cylinder Tacoma would cost you. My 2wd Tacoma manual trans gets 30mpg pretty easily and I’m never tempted to get a hotel. The price difference in the two vehicles alone may well make up for the extra cost in fuel and potentially tempting lodging plus even in a 2wd pickup you will have a much easier time going off the beaten path then you will in a low hanging passenger car.

Minor variances are applications to your municipality to suspend a particular by-law to allow your project to proceed, based on common sense or precedents set by other buildings in your area. If your municipal committee of adjustment denies permission because a neighbour voices concern over the development, you would have to appeal the decision to the municipal board of your particular province. In that case, you may be better off looking for another piece of property with an existing structure that you could renovate, more relaxed zoning regula­tions, a larger lot, or more congenial neighbours. 
Low-tech tools are high on value A basic set of handplanes lets you true edges, flatten panels or wide boards, and achieve finish-ready surfaces. Start with a small cluster of handplanes—low-angle and standard block planes, a No. 4 or 4-1/2 bench plane, and a jointer plane. A set of inexpensive chisels is essential for chopping, paring, and trimming.

After a permit has been issued, the building inspector will want to be notified at various points during your build in order to do a site visit, walk around and inspect the details to make sure that they meet code requirements. These inspections are commonly at the point where excavation work is complete, when the foundation is completed but before back-filling, when framing and all structural work has been done, after the installation of the insulation and vapour barrier, and then a final inspection after everything is complete. You may need to have a separate plumbing inspector if you’re adding or changing plumbing fixtures, and electrical work will need to be inspected by the appro­priate electrical inspector (in Ontario, the Electrical Safety Authority). In my experience, inspectors appreciate good work, a clean, safe site, and are willing to work with hom­eowners and builders to make sure that the work will meet code and will endure.
Planning your store layout is no small task, but many small retail store owners do it all themselves with great success. So why not you? Take it slow, follow our seven steps, and remember to put the customer first. With the ideas in this guide and a little elbow grease, you’ll soon be on your way to mapping out a retail store that’s easy to navigate, welcoming to customers, and best of all—profitable.
Now this Super Pencil from C.H. Hanson does all of that and more. The entire pencil is made from a non toxic graphite composition so the whole thing is a writing surface with no wood around it to shave away. Super pencil marks are water and smudge resistant and because the composite is so durable it never needs sharpening even when you use it on rough materials like concrete.
Other than that, you can’t have too much light — especially north light! — and you want accommodations for all the electricity you can imagine. Ceiling fans are a must. A good dust collection system is good, too. Don’t forget to plumb in for compressed air. Do NOT use hard PVC water pipe for compressed air — ever. If/when it breaks or ruptures, it explodes into tiny sharp glass-like shards. I know firsthand. I’ll tell you about it some other time. Think balloon popping!
In an indoor or basement shop with industrial carpeting, lay down inexpensive laminate flooring to make your life a bit easier at the end of the day. Be sure to anchor the panels or place a large rubber mat beneath to keep them from sliding over the carpet. (Covering up your carpet is even more critical if you want to go beyond wood and work with a material such as aluminum in your indoor shop; metal shavings dig into any kind of carpeting and are incredibly frustrating to clean up.)
When I change blades on my band saw, I usually need to adjust the thrust bearings and guides with an Allen wrench. I was tired of hunting around for the wrench, so I decided to stick it to the steel housing with a rare earth magnet (neodymium) about the size of a jacket button. Now it’s always handy! — Bill Wells. You can also use a magnet on your ladder.
As a carpenter, I need to bring certain items with me every day. I bought a cheap plastic tote in the tool storage area at a home center and modified it for my needs. I made a small plywood deck, drilled a couple of 3-in. holes for coffee cups or glue bottles and then fastened it to the tote. Another piece of plywood has holes to keep pencils upright and organized. My tote sits nicely on my bench seat, but it could also be attached to the floor with hook-and-loop fasteners. You could easily customize these totes for plumbing, garden or painting tools, electrical supplies—what have you. — Don Simms. Check out this jumbo tote for fasteners.
If I had it to do over again, I would stick to an entry level miter saw and table saw until I had both the funds and need to upgrade to more capable saws.  Because of this, I'd stick to the two saws we looked at in the $500 build: ​The Craftsman Table Saw for ~$150 and Hitachi 10 inch Miter Saw for ~110.  These two additions bring our running total to just over $500.  
×