It does sag a little bit, but not worryingly so. As I mentioned, it often rests on top of the large plastic boxes I place underneath, and I put in a small wooden brace at the entrance. You could definitely build it slightly smaller, or put in a more substantive center brace — like a sheet of plywood that fits into the groove of the bed liner and is the exact height you want.
Store design experts agree that this area should be open, inviting, and free of overpowering displays and signage clutter, as shown in the image above. Many customer behavior studies, including those conducted by Envirosell’s Paco Underhill, support this opinion. They show that customers tend to ignore displays, signage, and even manned sales counters placed close to store entrances.
You’ve probably considered what goods and services you’ll be offering, but have you researched the cost of sourcing your raw materials? How about the cost of turning those raw materials into your finished product? Do you understand how much you’ll need to charge for your products/services in order to cover the expenses of renting a space, paying employees, leasing equipment, and paying for permits and regulations? Moreover, have you considered if the answers to these questions will provide the kind of operating margin you’ll need to pay yourself a salary?

Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
I have been working on building out the space, starting with a new welding table and small material/saw rack. I was able to dedicate a 20' x 28' area to fabrication. I need to figure out some things like angle grinder storage, fume exhaust hood and cold saw set up, but I will get there. Power is one nice thing with a 400A 208VAC 3ph supply panel. Also got the compressor in a sound dampened closet with cooling so the noise level is down significantly. Oh ya, dedicated 15 ton AC for the shop has been nice.

Ideally, the stands should lift the speakers to roughly ear level of a sitting person. This is important because it aligns the ​subwoofers and tweeters relative to the ear and achieves the best balance of sound. The high frequencies are often missed when speakers are placed too high or too low. Speakers placed on a shelf or table often cause the surface to vibrate, thus distorting bass. These speaker stands isolate the speaker's vibrations from the floor, allowing you to hear the bass from the speaker and not the vibrations from a shelf, table or floor. Speakers come in various sizes and shapes, so the height of your speaker stands is dependent on your unique speakers. For this project, we give you the dimensions suited for the speakers shown in the photo, but you can alter the design to fit your individual needs.


Like most things in life, we believe that entrepreneurship can be learned, you just have to be willing to put one foot in front of the other. Aftering reading How to Start a Small Business 101, you’ll be equipped with the essential tools and resources you need to succeed at planning, raising capital, and executing crucial day-to-day business operations.
I used your set-up as a guide in building mine. It is a little different – it’s shorter a little bit, as I have a shorter canopy cover and I didn’t make the sleeping platform flush with the walls of the truck bed – but it turned out great! I’m really happy with it. Also, one of my favorite parts about it is none of it is actually attached to the truck. So I can take everything out and it makes cleaning a little easier. I’d post photos if I knew how. If you feel like seeing it let me know and tell me how to get them to you!

Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
When starting your small business, the easiest way to go about choosing a business name is to approach the task the same way you approach building new relationships. Did we lose you for a second? Here’s what we mean. It takes just one-tenth of a second for us to judge someone based on a first impression. There are endless relationships that instantly blossom or never get off the ground based off of this one simple fact. Most of us, even if it is on a subconscious level, understand this. Which is why when we meet someone that we are trying to impress, we make an attempt to adjust our appearance, body language, even the way we talk, to ensure we are putting our best foot forward.
A great freestanding beverage cooler should come equipped with a thermostat that lets you control the temperature to your liking — the colder the better for carbonated drinks, which tend to taste best when served at a frosty 34 degrees. If you plan to store adult beverages in your cooler, look for a model with a lock to keep your drinks away from children and teens. You’ll also want a model that allows you to reverse the way the door swings when you set it up, as this will provide flexibility in your workshop layout to help maximize your space.
If you have the available time, taking your DIY campervan for a test run (or two) is a great way to identify any problems while you still have access to tools, package deliveries, and a place to work. There’s just a lot that you can’t foresee until you live in your van. Taking it out for some short trips throughout your build will help you understand how you’ll actually use your new living space, what’s necessary, and what’s not.
Use this model whether you’re looking to turn your team of one into a two-person shop or you’re hoping to build out your marketing department to a team of 10 or more.  By focusing on the skill sets your business needs to be successful — rather than on the resume of an individual candidate — you’ll ensure vital functions are covered while expanding in a sustainable way.
Calculating the size of your desired parking lot is easy. The rule of thumb is to have a parking spot for every three customers. Determining traffic is trickier and potentially more lucrative. To help, we wrote an article on how to calculate your desired foot traffic. If you want to calculate your desired vehicle traffic, you can refer to our article on how to choose a location for your restaurant.
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
I grew up in New Jersey and now live in the Pocono Mountains of Pennsylvania. Good thing, too, because we certainly need that extra property space to store the leader of the Auto­bots.Back in 2013, I founded an Internet company called AmericasFootprints.com, which gives people an opportunity to preserve their most precious memories (in private) for the current and future generations of their family. That’s because I believe everyone has a story and I also believe everyone deserves a chance for their story to live on.
Do you carry items that bring your customers back time and time again? Consider placing these primary and similar secondary product lines toward the back of your store. Or, if your stock is constantly changing and you don’t carry replenishing goods, place your sale items toward the back. That way, customers must pass your new items and promotional displays on their way to check out the deals in back. 

Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
We have a 5-gallon clear plastic Hedpak container that our sink drains straight down into. We really like this container because it’s clear, which means we can easily see how full it is. With 5 gallons of gray water capacity, we only need to empty it every 3-4 days. Dumping is easy - just remove the tank from under the sink and pour it out into an RV dump facility or other approved area.
Hey Kasey, I don’t do anything for insulation, I treat truck camping just as I would cold weather tent camping. Just bring a good sleeping bag and learn how to manage in the cold. Usually the side wall of the truck is not at a perfect 90 degree angle, so you will need to check out the angle and compensate. You can hold up a small piece of 2×4 at the back to judge the angle and make a few test cuts to ensure it sits “flat” aka level.
Becoming a small business owner is one of the most rewarding and inspiring journeys a human being can take. It provides you with a chance to be your own boss, take control of your financial destiny, and become a meaningful contributor to your local economy and community. There will always be a reason not to take the plunge. But if there is one rule of small business — and life — is that nothing will happen if you don’t make it happen.
Since there’s less wiring involved, installing LED strip lights is much simpler than puck lights. You also won’t need to cut any holes because strip lighting should come with its own adhesive. We’ve seen most vanlifers stick strip lighting down the side edges of their ceilings. However, it’s not as easy to create separate lighting zones as it is with puck lights.
The time of the travel agent might be passing, but people are still looking for those with a knack for more nontraditional travel coordination. If you always plan the perfect vacations complete with beautiful hotels, the ideal location, and a bevy of delicious restaurants lined up for every evening, consider advertising your services as a more modern approach to travel planning.
It almost goes without saying that everything about your shop's design should project the right answers to each of these questions. But in today’s market, you have to go one step further. In our digitally connected world consumers have seen it all. The true art of compelling store design is in telling a story about your business, while simultaneously anticipating the needs of your customers. It’s all about the surprise and the delight.
I wanted to have numerous outlets, and have enough elec­trical service that I did not have to worry about overloading circuits. There was already some lighting, so I simply picked off that line and added additional lights to keep things bright and cozy. I ran a 240V line for the table saw and jointer with a dedicated breaker. For wall outlets, I ran 14-3 wire, and split all the plugs, so that I can run one machine on the upper plug, and another on the lower plug of any outlet.
I’ll throw this suggestion out to you too – while a warm sleeping bag would be a good start, maybe a couple sheets of plywood to put over the truck bed with a tarp over that would provide you some extra protection from rain/snow and also trap in some body heat. You wouldn’t have to make them permanent and could just slide the wood into the bed when not sleeping under it. A cheap bivy as Ryan suggested would also be a good consideration and a quality sleeping pad to provide some warm rating and comfort from the truck bed.
The refrigeration setup in your van is an area where you really do get what you pay for, whether you’re paying in money or in time. The best options are the most expensive. The cheapest options are a pain and/or don’t work very well. And if you try to save money with a DIY refrigerator setup, you could end up spending a lot of time on installation.
Hi thanks for the info. I’ve got a 2009 tacoma and went with a simple, no screws elevated system. I’ve also got a mx series ARE shell with rack rails so I’ll probably take too much stuff now. Oh well. My question is: how did you attach the plywood to the life gate? My carpentry/construction skills are best illustrated by the “Homer Simpson spice rack”. You used the existing holes in the tail gate, but did you put the tail gate cover back on the tail gate and put the plywood over it and screw thru both or ditch the cover? Thanks
Because workshops are rough and tumble places, the right fan for the job will have an industrial-strength motor and adjustable fan speeds. Easy-to-clean metal blades and a fully encased motor housing are also important features, especially if your shop tends to fill up with sawdust, wood chips and other fine debris. That extra layer of protection will help the fan motor last for years instead of being damaged by particulates.
When you set out to start your small business, investing in the right technology and equipment should be considered in conjunction with your store design. They should seamlessly integrate with and improve the customer experience in your store. Everyone remembers their first trip to the Apple Store and the “wow” moment of having their sale rung up by the assistant in the middle of the store, rather than having to wait in a line. But fewer people probably notice the carefully positioned heater that creates a warm environment for them as they walk through the door. It’s all part of the same idea.
WOW that is a nice size shop! I am looking forward to more videos on the shop projects! We have been shopping for a house for over a year & have finally found one but it has nothing for me to use as my woodshop! I currently have a basement shop that’s 24×40 & it’s really huge for me I couldn’t imagine any bigger. Anyway I will be looking at building a new woodshop for myself (yes I am a female woodworker) & you have given me lots of great ideas so far. I am an Artist & wood is my preference, everything I make is quite small (no furniture or anything that big) but I have lots of specialty tools for what I do as well! Thank you for sharing your ideas & all that you do. Keep up the great work!
If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.
×