Nice setup Ryan. I’m looking more for the storage aspect than the sleeping in aspect. I like how you used the cap clamps to hold things in place. Do I understand right that those are the only things holding the side shelf units in place? That and maybe the ribs in the floor of your bed? So if you unclamp the cap, the whole side cabinets would just slide out?
Ultimately, I did this to inspire my son. I want him to look at what I have done as a father and be proud. But I also want him to grow up into a strong man who faces fear in the eyes and doesn’t back down because of a challenge. I want him to say to himself one day, “if my dad built Optimus Prime, then I can do anything I want to do in life.”  I want him to succeed in every possible way imaginable, even when I am no longer around to help him through those challenges.
One of the challenges in building a cabinet for hand tools, is that as soon as you define a place for each tool in your custom cabinet, you find that you need more room to store the must have tools you just bought. I decided to make a couple of open cabinets, and employ the use of inserts that can be replaced or modified as my tool collection grows. Part of the goal was to make a clean, efficient shop, while keeping to a budget. I bought paint grade maple plywood and made the cabinets. Applying a solid maple face frame to the cabinet makes a clean looking cabinet from sheet goods purchased at $50/sheet.
First, decide on wax you would like to start with, there are three different kinds to choose from Ultimate Small Shop paraffin wax, soy wax, and beeswax. Paraffin wax is most commonly used in candles, this wax is found at most candle making stores. Soy wax is all natural, made from soybeans, and cleans up easily with soap and water. Beeswax is all natural too, and making beeswax candles is often easiest because you simply wrap a sheet of beeswax tightly around a wick then seal it with your thumb, which means no melting is required. To begin, spread newspapers around the candle making area. First, you melt your paraffin or soy wax and it must be double-boiled. Usually, you place a large pot that is about half-filled with water on a burner over low-medium heat, place a melter in the water, then gradually place wax pieces into the melter. When the wax has melted, you can add coloring or fragrance as desired. To make molded candles, cut the wick two inches taller than you want the candle to be, then thread it through the hole at the bottom of the mold, then plug the outside of the hole with putty. Place a pencil or similar item over the top of the mold and tie the top of the wick to it, centering the wick. If the mold is cardboard, plastic, or glass, heat the wax to 130 degrees Fahrenheit. If the mold is metal, then heat the wax to 190 degrees. You can use a candle or candy thermometer to measure this. Ultimate Small Shop Pdf When the right temperature is reached, lift the melter by the handle and slowly pour the wax into the mold. Let cool for twelve hours then refrigerate for twelve more hours, then your candle is ready to be removed. To make votives and other small container candles, you can use pre-tabbed wicks by simply placing them in the center of the votive candle molds or containers, then pour the wax mixture over and let stand for twelve hours, refrigerating the votives. By the time your teen is in high school, you probably aren’t taking as many pictures of them as you used to. I have to keep reminding myself that I only have a couple of years left and no time to waste trying to capture fleeing teenage memories. You might be thinking that I’m really organized to be already working on scrapbooking my daughter’s high school memories. To be honest, I have a shoebox full of pictures of my daughter waiting for me to get to someday. But if I wait until “someday” to continue taking pictures because I already have so many pictures I haven’t done anything with, then my daughter’s teenage years will come and go while I try to catch up. I don’t want to chronicle every detail of my daughter’s life (nor would she want me to!), but I was trying to think of some memories that she might want to laugh about and maybe even treasure someday. Ultimate Small Shop Guide Woodworking So how do you do that without ending up with pages and pages of memories? I decided to do two large (12×12) pages (facing each other in the album) for each year of high school.
My shop ended up being 23 x 19 feet, for a total of 437 square feet. I put my wood rack in the basement, but out­side the walled in shop area. To keep the dust in the shop, a three part strategy was employed. I have a dust collection system, an air filtration system and a shop vacuum for cleaning dust out of machinery. I put up new walls, installed new electrical service, lighting, and two access doors for ease of materials move­ment. The shop includes two windows so that I can enjoy natural light, and not feel like I am squirreled away in the basement.
If you want to spend as little as possible on a vent fan, the Fan-Tastic Vent 1200 (about $130) is your best bet. This fan has three speeds and manual controls, and it has the same quiet operation and energy efficiency of Fan-Tastic’s other fans. If you find that you need to use it while it’s raining, it’s easy to add on an Ultra-Beeze Vent Cover later on.
When starting your small business, the easiest way to go about choosing a business name is to approach the task the same way you approach building new relationships. Did we lose you for a second? Here’s what we mean. It takes just one-tenth of a second for us to judge someone based on a first impression. There are endless relationships that instantly blossom or never get off the ground based off of this one simple fact. Most of us, even if it is on a subconscious level, understand this. Which is why when we meet someone that we are trying to impress, we make an attempt to adjust our appearance, body language, even the way we talk, to ensure we are putting our best foot forward.
Do you carry items that bring your customers back time and time again? Consider placing these primary and similar secondary product lines toward the back of your store. Or, if your stock is constantly changing and you don’t carry replenishing goods, place your sale items toward the back. That way, customers must pass your new items and promotional displays on their way to check out the deals in back.
As the old saying goes, the only two inevitable things in life are death and taxes. Almost all small businesses in the United States are subject to some form of corporate income or gross receipts tax on a state level — that is, unless you happen to be a lucky inhabitant of the great states of Wyoming, Nevada or South Dakota. Actually, even these states will require you to pay state workers' compensation insurance and unemployment insurance taxes. Oh, and of course every small business in the country is subject to some form of federal taxation.

If you’re a high volume QSR for example, you’re going to want clear signage that helps customers identify where they should be lining up and perhaps a product display next to the line. If you have high risk merchandise in your store, you’ll want to design your shop so that customers must pass the point of sale on their way out and use mirrors to eliminate blind spots in your business.


A great freestanding beverage cooler should come equipped with a thermostat that lets you control the temperature to your liking — the colder the better for carbonated drinks, which tend to taste best when served at a frosty 34 degrees. If you plan to store adult beverages in your cooler, look for a model with a lock to keep your drinks away from children and teens. You’ll also want a model that allows you to reverse the way the door swings when you set it up, as this will provide flexibility in your workshop layout to help maximize your space.
Do you want to create the next great retail dynasty? Do you want to be Abe Froman, the Sausage King of Chicago? Or are you just looking for a simple local lifestyle business? Are you hoping to create a franchise model? Or do you see your local business as a testing ground for an ecommerce business? Your end goal will clearly inform your decisions, so it’s worth considering what it is early on.
Conversion vans have some pretty sweet built-in amenities, including high-tops for extra headroom. Many have comfy captain chairs, leather seats, mood lighting, TV/VCR, and a rear bench seat that folds down into a bed. If you’re not picky about your living situation, this could be all you need to get started. And if you gut it and customize it yourself, the high top offers tons of great storage options that other vans just don’t have.
I got extra batteries for my cordless tools, but I could never remember which battery was newly charged and which was run down. Now I can easily tell them apart because I painted a number on each battery with my kid’s white nail polish. It dries fast and is— you got it—“tough as nails.” — Tom Baker. Plus: Learn how to double the life of your car battery.
With all the time and effort you've put into properly merchandising your products, the last thing you want is for incoming customers to hurry past them — this ultimately limits the number of products they'll purchase. One way retailers combat this is through creating breaks that force them to pause. These are sometimes referred to as "speed bumps." Essentially, this can be anything that gives customers a visual break and can be achieved through signage or special/seasonal displays.

Firstly, more and more consumers are rebelling against the generic offerings of big-box retailers and seeking out the unique, personal touch offered by small, local business. You can leverage this message by weaving yourself into the fabric of your community. Canadian yoga apparel retailer Lululemon has enjoyed explosive growth thanks to their ability to do just this. According to their website, “A Lululemon store is so much more than a place to shop. It’s an education centre, a yoga studio and a meeting place. It’s a local hub for educators, ambassadors and guests to gather to learn, sweat and connect. It’s our lifeline to our communities and the soul of our company.” Lululemon uses free events to make people feel that they have a sense of ownership over the brand, and you can too! Getting people through your door is 90% of the battle and event marketing definitely can bring in crowds.


Use this model whether you’re looking to turn your team of one into a two-person shop or you’re hoping to build out your marketing department to a team of 10 or more.  By focusing on the skill sets your business needs to be successful — rather than on the resume of an individual candidate — you’ll ensure vital functions are covered while expanding in a sustainable way.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Power outlets are also needed for lighting, heaters, AC units, radios, televisions, CNC machines, 3D printers, and computers—all of which you’ll find in many workshops (although maybe not together, and maybe not all in your garage.) You simply can never have too many outlets and it’s much safer to have too many than not enough. Bring in an electrician to help install your outlets and setup 220v power if needed for larger shop tools.
If you have the available time, taking your DIY campervan for a test run (or two) is a great way to identify any problems while you still have access to tools, package deliveries, and a place to work. There’s just a lot that you can’t foresee until you live in your van. Taking it out for some short trips throughout your build will help you understand how you’ll actually use your new living space, what’s necessary, and what’s not.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.

Ultimately, the cost of your coffee shop starts entirely with you. Your coffee shop business concept plays a huge role in what direction you'll go in and what your budget will look like. So if money is an important consideration to starting your coffee business, review what kind of coffee business makes sense to startup at this point and time. We've recently written some articles on low cost ideas for coffee shop businesses.
There are many inexpensive alternatives lying around the house or at your local store you can use to create a Halloween theme that will impress all your friends.”One of the most popular party favors is a framed picture of the party guest taken at your kid’s party. He or she could be showing off a silly hat or party costume, performing an outrageous party game stunt, or wearing a face full of frosting and ice cream. Having party guests create their own make-and-take frame to display this memorable photo makes it an even greater treasure for the memory box. Start with a plain square of cardboard with an opening the size of your picture. When the decorating is done, Ultimate Small Shop Reviews simply glue the picture to the back of the frame. Why not turn that Cooking Interest, Comic Book Collecting, or Your Retro Clothing Collection Into A Home Based Business Venture! Most people enjoy hobbies they have pursued with great enthusiasm for years. Even though they may find their leisure activities fulfilling and enjoyable they never imagined making money with a fun hobby! Are you one of these gifted individuals? These talented individuals might have a passion for sewing fabulous original wardrobes, marvelous hand knitted items, furniture making, creative paintings, photographs, jewelry art, greeting card design, doll making, original toys, baby clothing, candle making, quilting, calligraphy, fancy soap making, about anything you can imagine! Crafting is actually a great way to start a home business on a shoestring. You might want to start on a small scale by offering your creative work to friends and family. Later on, once you have enough products, you might decide to rent a booth at local flea markets or crafts shows to display your work. As you may know, the Arts And Crafts Industry Is Enjoying An Amazingly Phenomenal Popularity. People are eager to purchase hand made clothing, furniture, custom made keepsakes or jewelry. If you have the creative talent this is one business you should consider! A friend, Joyce, diverted her obsession with candle making into a thriving business. She started by selling her hand made scented candles to friends and neighbors. Word of mouth spread about her candles. Soon she was receiving enough orders to keep her very busy. Joyce throws house parties to sell her candles and also takes custom orders from ads she runs in local newspapers. Next, she plans to take her candles to the stores and malls in her area.”Today is life – the only life you are sure of. Make the most of today. Get interested in something. Shake yourself awake. Develop a hobby. Let the winds of enthusiasm sweep through you. Live today with gusto.”Our hobbies help us to relax and forget our everyday problems and troubles. We are all experts in one or more fields of our lives. Ultimate Small Shop program But I am sure that not everyone has a hobby that makes money for him/her (except, of course, if you love your job).Just imagine, wouldn’t it be great if you could have money making hobby? You could get involved even more with what you already love to do, you could treat your family and friends with the extra cash, or… even quit your current job that you probably hate.
State Parks/Developed Campgrounds. Every once in awhile, it’s kind of nice to stay at a state park or other developed campground - and a big reason why is that they have showers (and sometimes laundry, too). This is what we’ve done most often when we need a shower on the road. Many state parks also have small day use fees if you don’t want to actually camp there.
Chris Marshall: You’re asking a question that would take many magazine articles or a whole chapter of a good shop-design book to answer adequately. If you haven’t already done so, you might also want to ask this question to the good folks that frequent our forum on woodworking.com. Every woodworker with a shop will have a slightly different answer, so here’s mine. I’ve never had a brick shop, but my last one was a metal pole barn (30 ft. x 40 ft.). I outfitted the interior with 2×6-framed walls and plenty of insulation. It stayed reasonably cool in the summer and warm in the winter, using a wall air conditioner and a 60,000 BTU furnace. Currently, I have a 24 ft. x 42 ft. garage space for my shop. It is framed conventionally with 2×6 walls and stick-built 2×10 rafters. I’ve only been in my new shop for about a year, but it is working just as well or better than my pole barn did, because the new shop has many large windows that let in lots more natural light. I’ve used 8-ft. fluorescent T8 light fixtures in both buildings with good success, and I ran both 110- and 220-volt outlets all around the room. The last shop had a plywood floor; the current one, a concrete slab. I thought I would notice a bigger difference between the two flooring types, in terms of how tired it makes my legs by the end of the day. But in all honesty, a good pair of supportive shoes seems to make the difference moot for me. Both types of buildings benefit from a dehumidifier during humid months (when I’m not running the A/C, that is) to keep the relative humidity low and my tools rust-free. If all things were equal, and money were no object, I would probably go with a conventionally framed wood building over the pole barn. It was easier to build that from scratch as opposed to retrofitting the pole barn framing with walls afterward. But, as I say, the next woodworker will probably offer you a completely different answer from mine. Good luck in your decision!
When starting your small business, the type of business structure you choose will depend on three primary factors: liability, taxation, and record-keeping. Most small business owners begin their commercial life as a sole proprietor because it’s the easiest way to get started. In fact, if you’re in business and you haven’t taken any action to incorporate, you are most likely deemed a sole proprietor by default. You are entitled to all the profits of your business but also responsible for all its debts, losses, and liabilities.
When you are looking for small business funding options, be it from the local bank, an angel investor, or even a family member, the first thing you will be asked to present after your business plan will be any existing financial records. Make sure you are putting your best foot forward by keeping meticulous records, with your business finances completely separate from your personal finances.
My contention has always been that you can build a serviceable shop in your home, develop your hand skills, and make fine furniture. In the past year, I had an opportunity to build a shop from the ground up after moving to a new home. I found a house with an unfinished basement, and set to work. In this article, I will discuss everything from layout, to electrical, to equipment selection. I intend to name names with respect to equipment, so that readers will know what I chose. Everyone’s budget will be different, but I think almost everyone will be able to treat this as a starting point, and adjust accordingly, depending on their own budget.
Make sure the room or building you are planning to utilize has sufficient lighting and electrical outlets to allow you to see what you are doing, and to work without excessive extension cords. You should also remember that many tools require a fairly substantial amperage to operate, so you need to make sure the wiring is capable of handling the loads. 20 Amp circuits will work for ordinary 120V tools, but air compressors and welders may require 40 Amp, 220V circuits.
Note: Some of the links to products that we recommend on this page are affiliate links. This means that if you click through one of our links and buy something, we get a small commission at no cost to you. This helps us keep this blog going so we can continue to provide you with van build tips, tricks, and guides. We believe in honest opinions, and we never recommend anything we don't know about. Every recommended product on this page we've either used personally, have personal experience with, or have researched heavily.

Wide aisles also prevent the dreaded butt brush, a term coined by top retail consultant Paco Underhill. His studies show that both women and men avoid tight or crowded aisles where they might brush bottoms with other shoppers. Really, this is a thing! Learn more about Paco’s retail research and insights in his book, Why We Buy: The Science of Shopping.
Evan Tarver is a staff writer at Fit Small Business, specializing in Small Business Finance. He is also a fiction author and screenwriter. His past experience includes investment banking, managerial finance, and technology. When he isn't busy scheming his next business idea, you'll find Evan holed up in a coffee shop in his hometown of San Francisco working on the next great American fiction story.
Do you have 3 goals left? Great! That's the perfect number. Do you have more? That's okay as well. If you have more time to work on your business, then you may be able to accomplish more then 3. But it also depends on the type of goal you are trying to accomplish. I just recommend not trying to over achieve in fear of not accomplishing everything you set out to do. 

Many retail fixture and display companies provide store planning and design services to their customers. Though typically not free, these in-house design services can be far less expensive than hiring an independent designer. Plus, they can help streamline the process of store layout and planning, along with the purchasing and installation of displays and fixtures.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
×