However, my guess is around $250,00 t0 $300,000. So as you say you will have a good mortgage to pay for. So excuse me for being nosy. I am retired and I have started setting up my shop in my two car garage. It is not insulated just bare walls and open ceiling. I am going to start doing some projects and will keep watching your shows. I was a Computer Engineer and although I liked my job i always had that desire to get back in wood working and now I am doing just that.
In general, a table saw requires at least eight feet in front and behind to accommodate standard sheet goods and four feet side to side. A work table should provide four feet clearance on all sides, and pathways between tables, benches and storage units should be three feet wide. Proper clearance will allow you to move about with ease while you work.
I have different toolboxes for different jobs around the house. Occasionally I’d grab a tool out of one box and then put it away in another. Eventually all my flat-head screwdrivers would end up in one toolbox. To solve the problem, I now mark the handles of the tools and the corresponding toolbox with a band of colored electrical tape. Now all the tools are in the box where they belong. — Kim Litkenhaus Marino
When you design your workshop setup, climate control often gets ignored — and that’s a huge mistake! If your workshop or hobby room is in an unconditioned space like a garage or basement, you could find that it’s brutally uncomfortable to work in there during warm weather. You’ll be much happier with a solid fan — or several — to keep air moving for your comfort.
Since your business name is often the first thing potential customers will see or hear, think of it as one of your key tools for leaving a lasting impression. The right name, like a firm handshake, can play a role in your brand’s perception. So make sure it’s strong, catchy, and unique, but most importantly sends the right message about your business.
Skoolies do have significant drawbacks, however. Their size makes them a bit unwieldy to drive, and getting to some of the more out-of-the-way camping spots just won’t be an option. If something goes wrong mechanically, it can be much more expensive to fix than a normal vehicle. Also, the sheer size of these vehicles means the gas mileage is much worse than other options.
So what does all this boil down to? I favour starting with a good workbench and top quality hand tools – chisels, a couple of planes, a hammer, a few Japanese handsaws – stuff like that. You’ll be amazed at what you can accomplish when properly equipped. Build simple items at first, and then add the very best power tools you can – as you can afford to – in the order that makes the most sense for the work you’re interested in. Yes, this gets you off to a slower start, but what’s the rush? You’ll soon surpass the ‘buy-it-all-at-once’ folks who end up struggling with beginner tools that hold them back from getting better.
Chris Marshall: You’re asking a question that would take many magazine articles or a whole chapter of a good shop-design book to answer adequately. If you haven’t already done so, you might also want to ask this question to the good folks that frequent our forum on woodworking.com. Every woodworker with a shop will have a slightly different answer, so here’s mine. I’ve never had a brick shop, but my last one was a metal pole barn (30 ft. x 40 ft.). I outfitted the interior with 2×6-framed walls and plenty of insulation. It stayed reasonably cool in the summer and warm in the winter, using a wall air conditioner and a 60,000 BTU furnace. Currently, I have a 24 ft. x 42 ft. garage space for my shop. It is framed conventionally with 2×6 walls and stick-built 2×10 rafters. I’ve only been in my new shop for about a year, but it is working just as well or better than my pole barn did, because the new shop has many large windows that let in lots more natural light. I’ve used 8-ft. fluorescent T8 light fixtures in both buildings with good success, and I ran both 110- and 220-volt outlets all around the room. The last shop had a plywood floor; the current one, a concrete slab. I thought I would notice a bigger difference between the two flooring types, in terms of how tired it makes my legs by the end of the day. But in all honesty, a good pair of supportive shoes seems to make the difference moot for me. Both types of buildings benefit from a dehumidifier during humid months (when I’m not running the A/C, that is) to keep the relative humidity low and my tools rust-free. If all things were equal, and money were no object, I would probably go with a conventionally framed wood building over the pole barn. It was easier to build that from scratch as opposed to retrofitting the pole barn framing with walls afterward. But, as I say, the next woodworker will probably offer you a completely different answer from mine. Good luck in your decision!
What I have done in my man cave of a shop is to install above my finishing table a strip of track lighting where I have fixtures ranging from the typical bright white incandescent (typically around 4700k) all the way to the average halogen spot that I figure someone would use with an art piece (normally around 3700K). this allows me to point each light and view my piece and finish under varying light conditions to judge whether or not I prefer a particular finish or not. It also helps in photographing items (though filming is a whole nother story, I still have my 5400k T8 overheads for working).
Then there are material considerations, such as how to bring full-size sheets of plywood home to cut down to size (you don't). And safety and cleanup are two more concerns: Proper ventilation and dust collection, a cinch in a larger shop, can be quite a challenge (and a potential health hazard). Nevertheless, you can set up a great wood shop in a small space, and we'll show you what you need.
Nicole and I decided not to go public with the cost of the build. Although we are very open about most things, we are a little uncomfortable about making an expenditure of this magnitude public knowledge. Furthermore, unless you live in the Phoenix area and plan on building the same size shop with the same patio and with all of the same finishing touches and labor requirements, the price isn’t all that helpful to you.
Dressing rooms are a must in most apparel stores, but they do take up valuable floor space. Make the most of dressing room areas by using adjoining walls for promotional items and accessories like belts and scarves. If you provide dressing areas, be sure at least one door and changing space meets the Americans with Disabilities Act accessibility guidelines, too.
Hey Ted! If you mean to ask whether you could sit up from one of the vertical sidebins and have enough headroom under the Leer 122, I think that would be a no. You’d have to build the sidebins to be a little shorter. At least with my truck, that would be the case. Perhaps with a full-size pickup you would have enough room thanks to the overall size increase of the canopy as well.
Have a walk-through yourself and see where the visual cues guide you or get your staff, friends, or family to do the same and give you honest feedback. Don't forget to observe your customers and see what they're drawn to, what they avoid, and how they move, then match that with your intended design. If you keep resilient and keep your eyes and ears open, you'll be sure to create a retail design that's a win-win for both you and your customers.
This project may look a little overwhelming and I do consider myself pretty handy. However, I think just about anyone could complete this project. This was my first real experience building a solid floor, framing walls and sheathing/ shingling a roof. I spent a lot of time researching and educating myself on proper construction techniques. I have not come across any glaring mistakes along the way, but I welcome comments about the construction from more experienced builders.
Ultimately, your workshop should be a place that inspires you to be creative and to do your best work. When you take the time to plan the space for maximum efficiency and comfort, you’ll love spending time there — and that means you’ll get more done, whether it’s fixing up a car or building a new piece of furniture. No matter how you use your workshop, you should enjoy the time you get to work with your hands and make something brand new. So what are you waiting for? Get started designing your perfect workshop today.
Nice video Marc. I did enjoy seeing the details of the construction process. Since becoming a homeowner and a woodworker (something that happened literally at the same time) I have become fascinated with anything having to do with the process of building and finishing and all the details in between. I thought of an off the wall question while watching this video and that is do you write yourself any kind of script for any of your monologues and/or narrating or do you just have a general idea of what you want to say and wing it?
I look at these workshops and wonder if I'm the only woodworker that has other hobbies that require shop space. My one car garage serves for woodworking, motorcycle storage and maintenance and home repairs. I have a floor standing drill press, Band Saw, 10" cabinet saw, lathe, 6" jointer, 3 tier tool chest(automotive tools only) 4' workbench, mortiser on a pedistal, grinder on a 16" square storage cabinet, and a roll around 40"x22" cabinet that hold my miter saw, portable thickness planer and other storage. Luckily I have an attached shed where I can keep my dust collector and compressor and have them plumbed into the shop. Right now my snow blower also resides in the shop where otherwise my 450cc KTM off road motorcycle would. I need to step outside in order to change my mind so please stop teasing me with these to die for shops. Paul
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience.
The frost generated by Canadian winters wreak havoc on structures through their foundations. According to code conventional foundations and footings must rest below the reach of frost on undisturbed soil (in most provinces, this is safely considered to be 4 ft. below ground level or grade), bear directly on bedrock, or be frost-protected. A shallow foundation may be possible in your area in an outbuilding if you can get an engineer to design and stamp plans for insulating the area directly beside your shallow foundation wall so that frost will not form beneath the footing area and cause damage. A slab-on-grade foundation for an outbuilding is another option that will need to be designed by an engineer so that the concrete slab will structurally bear the weight of the shop structure you build above it.
The core criteria of small business site selection will always be foot traffic and ease of access. In places like New York City, this means being by the subway or on a busy street. But for most of America it’s about considering traffic flow and parking accessibility. Ever see three gas stations at the same intersection? They are all picking off different traffic flows because they know customers are looking for the shortest possible detour.
If you want to run a business operated by yourself and more than one employee, you may run into zoning issues if your location is zoned for residential use only. It’s common for municipalities to allow and encourage home-based businesses but there will likely be a maximum area that you will be permitted to add for business purposes. If you try to build a shop that will contribute noise and traffic (from employees or deliveries) to an urban neighbourhood, you run the risk of running into opposition from neighbours concerned by the impact your shop will have. Your municipality will have planners with whom you should consult as you begin to define the possibilities that your property will allow.
Many small businesses in New York and New Jersey were forced to close following Superstorm Sandy because they lacked the insurance that would have gotten them back on their feet. That part is well known. What’s less well known is that this lack of proper insurance, coupled with the lack proper legal incorporation, resulted in many entrepreneurs seeing their personal assets come under threat.