Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
Ok, the leap from $1,000 to $2,500 is a big one.  I certainly didn't make it at one time.  It took me years.  But I know folks that decided they wanted to get into woodworking and dropped at least $2,500 getting themselves outfitted.  When you do make the jump, the thought process becomes much less about making sure you can get the job done and becomes more about having quality tools to get the job done.
Above all, remember that all of these elements can form part of your negotiation. Unless you are pursuing a highly desired space in a hot rental market, there is usually a point of leverage available to you in every lease negotiation. When it comes to getting the best possible deal in these situations, you’ll want to seek quality professional advice, this will normally include a broker and real estate lawyer.
Due diligence is the process of going through the current owner’s books with a fine-tooth comb to verify inventory information, sales data, average ticket price, and every other aspect of the business. Doing all this yourself is difficult and time-consuming, so you’ll probably want to involve accountants and lawyers to ensure that you cross all the t’s and dot all the i’s. A big red flag to watch out for here is how intertwined the current owner’s personal expenses are with the business accounts — this can obscure the genuine flow of cash in and cash out of the business. The purchase price of an existing business is often calculated as three to five times the net annual revenue, so you’ll want to take that figure into account before you make an offer.

It does sag a little bit, but not worryingly so. As I mentioned, it often rests on top of the large plastic boxes I place underneath, and I put in a small wooden brace at the entrance. You could definitely build it slightly smaller, or put in a more substantive center brace — like a sheet of plywood that fits into the groove of the bed liner and is the exact height you want.
Finally, at the beginning you'll do just fine with a basic set of router bits that run ~$40.  A starter set will typically include straight bits for edge matching material, a selection of edge finishing bits, and some joinery bits.  As you work on a few projects you may find that more specialized bits are needed.   But specialized bits are expensive - so purchasing them as you have a specific need makes more sense than buying in anticipation of a need.
If you’ve spent time at your local flea or farmers’ market over the last few years, you may have noticed the explosion that has taken place in the number of innovative small business concepts. From cool new clothing lines to ingenious fusion foods, the sheer diversity of the ideas on display really hammers home one of the key lessons when starting a small business: You need to find your key differentiator. For some this is their brand story, for others it’s the value of their service, but for many quick service restaurants and small retailers, it’s a distinctive core product line that demands the attention and interest of your customers.

Do you have a business license? Do you have a permit to open a food service establishment issued by the local health department? Are you applying for a permit to modify the building you wish to occupy? Do you have a health permit from the county health department? Do you have a signage permit? How about an alarm permit from your city or county fire or police departments? These are just a few of the questions you need to ask yourself.
Congratulations on building such an awesome shop. Ultimate man cave! Glad you have a cooperating HOA. I’m currently inviolation of my CC&Rs since I occupy 1/2 of a two car garage and the rules say you can’t use the garage for anything other than your car. So far no violation letters. One thing your missing…a fridge. Looking forward to many more guild builds.
In every aspect when starting your small business you should be mindful of making careful, prudent decisions about the allocation of your potentially limited funds — tracking precisely the cost of goods sold (CoGS) against sales to ensure profitability. Every dollar spent is tracked and accounted for, either as an essential cost of doing business (rent, employees, etc.) or as a cost of inventory that will result directly in profit.

Love the design. I’ve got a 15 tacoma, which has rails that run the length of the bed and are what my shell is “clamped” into via a bed rail nut. Hence my problem with following your outline verbatim. Any suggestions for incorporating the rail as a substitute for the 2×4 you clamped into your truck? Essentially connecting the 3, 2×4 braces directly to the rail… I’m a construction novice, any suggestions greatly appreciated!
Disclaimer: We spend hours researching and writing our articles and strive to provide accurate, up-to-date content. However, our research is meant to aid your own, and we are not acting as licensed professionals. We recommend that you consult with your own lawyer, accountant, or other licensed professional for relevant business decisions. Click here to see our full disclaimer.
×