One of the best deals on portable power tools, including routers and sometimes planers, comes in the form of factory-reconditioned tools. These are primarily tools that have been repaired at the factory after failing quality inspections or being returned by customers. While they cannot be sold as new, they are identical to new tools in quality and appearance and usually feature the same warranty (be sure to check). Typical savings are anywhere from 15% to 30%, though you sometimes can find even bigger bargains. These tools can be found at Amazon.com and other online tool sellers. It is also possible to buy them through retail stores and, in some cases, directly from the manufacturer’s Web site.
We do not recommend using Reflectix to insulate your walls or ceiling. Without an air gap, the R-value of Reflectix is about R-1. Even if you have the recommended ¾” air gap next to the Reflectix, the R-value per inch is less than R-3. There are much more efficient and cost-effective insulation materials out there for these purposes - you’ll be better off filling the space with rigid foam board.
“Zone design successfully helps shoppers locate what they want while exposing them to products that enhance the ones they are buying. Increased transaction totals are a natural byproduct. Products are categorized by use into Zones, such as ‘kitchen/cooking,’ ‘entertaining/dining,’ and ‘home decor,’ with inventory range and stock levels determining the size of each Zone.
Conduction is heat transferred across solid surfaces- think touching a hot stove. It’s also how heat gets out of your van in the winter. The heat inside your van is conducted through the solid surface of your walls and ceiling. Insulating the inside of your van will help prevent heat loss through conduction during the winter, and will also stop your van from conducting the sun’s heat inside during the summer.
You can buy full solar kits that have all the components you’ll need except for the batteries and inverter. Kits come sized as small as 100 watts (one panel) and as large as 400 watts (four panels). Whatever you go with, we highly suggest getting an MPPT charge controller, which are a little more expensive but much more efficient than PWM charge controllers.
Assembling parts is easiest when you can work at a comfortable height. But the height of that working surface depends on the size of the project. These ABC boxes, so called because they’re made with sides of three different dimensions, make a variable-height assembly table base. By rotating the boxes or standing them on end, you’ll get three different working heights.
I place the band saw first in my order of purchases, because I consider it the heart of the shop. Band saws are very safe tools for ripping, re-sawing, cutting curves and more because all of the force is downward, virtually eliminating any chance of unexpected kickbacks. I wanted a saw that had a strong back, dynamically balanced cast iron wheels for smooth operation and flywheel effect, 12" depth of cut, good dust extraction design, a large table and a solid fence. After shopping around, I settled on the General International Model 90-170 14" saw. It is very smooth, comes with an Excalibur fence, and it is light enough (133kg) to move into your basement without crushing someone.
When you are looking for small business funding options, be it from the local bank, an angel investor, or even a family member, the first thing you will be asked to present after your business plan will be any existing financial records. Make sure you are putting your best foot forward by keeping meticulous records, with your business finances completely separate from your personal finances.
To get the most out of your router, you are going to want a router table.  You may find yourself asking if you really need one - if you do, check this post out.​  It's one of those purchases that you won't truly understand how valuable it is until you have one.  Given the budget of $2,500, I'd suggest looking at the Bosch RA1171 ($150).  If you want to see our favorite tables along with write-ups, check them out here.
Due diligence is the process of going through the current owner’s books with a fine-tooth comb to verify inventory information, sales data, average ticket price, and every other aspect of the business. Doing all this yourself is difficult and time-consuming, so you’ll probably want to involve accountants and lawyers to ensure that you cross all the t’s and dot all the i’s. A big red flag to watch out for here is how intertwined the current owner’s personal expenses are with the business accounts — this can obscure the genuine flow of cash in and cash out of the business. The purchase price of an existing business is often calculated as three to five times the net annual revenue, so you’ll want to take that figure into account before you make an offer.
To simplify this process, hire professionals with experience helping business owners by assessing their needs, developing their budget, and negotiating their commercial lease. Managed by Q is a company that not only assists with pre-lease planning, but also provides help with renovation project management, space planning, and even administrative support. Managed by Q offers an array of services that can help save you time and money. Click here to set up a free account and get started.
I don’t think you have run into this problem, but I have to deal with condensation in the cap as I live in a moist climate. I was thinking of an old van type roof vent with fan for active ventilation, or drilling holes along the side of the cap, inserting short cuts of pipe with fine screens (mozie land), and capping them. This way I could control for rain, cold, etc., but create some passive cross ventilation at roof level.
Hey Joe, I just hit 178k on my truck. I remember when I started out the first time around it had like 144k or so. They are known to go quite far, so we’ll see how it goes. Maintenance on the road… I just stop at those oil lube places for the most part, and do regular weekly checks under the hood for fluid levels, etc. I’m not too mechanically inclined!
So after 14 years in our previous location, my company moved to a new shop last month. My shop went from 1600sqft split into 2 bays with the kitchen in between to a contiguous 2950 sqft. Still don't know why the the office portion needed to grow by the same percentage when there were already 10 empty cubes at the old office, but thats an argument for another day. The boss got his 500 sqft office so he is happy.

The nomadic truck camping lifestyle has been incredibly freeing, not only is cheap and accessible to most anyone, but it can take you beyond places you even imagined. One book that I’d recommend to all newcomers to this lifestyle is Bob Wells’ How to Live in a Car, Van, or RV, which will help you better understand the ins and outs of this lifestyle.

The tablesaw—This tool is the backbone of nearly every shop, and for good reason. It allows unmatched precision in ripping parallel edges and crosscutting at a variety of angles. Most woodworkers find it crucial for the basic milling of stock. It is also suited to many joinery tasks, easily producing tenons, box joints, and—with a reground blade—the tails for dovetail joints.
Non-Standard Miter Slots - This one is a downer.  One of the primary advantages of having a table saw is access to jigs that expand the saws functionality.  This is a major issue if you plan on buying after market jigs.  Given that we are limiting the cost of this buildout to $500, I am guessing that after market jigs are probably low on the priority list.  Your going to want jigs once you start researching what they enable you to do, my advice is to build your own - there are plenty of plans online.  
×